Please wait a minute...
工程设计学报  2017, Vol. 24 Issue (2): 168-173,195    DOI: 10.3785/j.issn.1006-754X.2017.02.007
设计理论与方法学     
电连接器接触件插拔特性仿真与试验研究
骆燕燕1, 杨静宇1, 任永隆2, 张元磊3, 李文君4
1. 河北工业大学 电气工程学院, 天津 300130;
2. 93721部队, 山西 大同 037000;
3. 中国汽车技术研究中心, 天津 300300;
4. 河南省新闻出版广电局 设备处, 河南 郑州 450018
Simulation and experimental study on plug and pull characteristic of electrical connector contact
LUO Yan-yan1, YANG Jing-yu1, REN Yong-long2, ZHANG Yuan-lei3, LI Wen-jun4
1. School of Electrical Engineering, Hebei University of Technology, Tianjin 300130, China;
2. Unit 93721 of the PLA, Datong 037000, China;
3. China Automotive Technology and Research Center, Tianjin 300300, China;
4. Equipment Office, Administration of Press, Publication, Radio, Film and Television of Henan Province, Zhengzhou 450018, China
 全文: PDF(2032 KB)   HTML
摘要:

为探究电连接器接触件插拔过程中各监测量变化情况,并分析接触件不同结构参数对电连接器插拔特性的影响,利用ANSYS对接触件插拔过程进行仿真,得到了插拔过程中插孔簧片变形、应力分布以及插拔力和接触压力的变化情况,分析了接触件不同结构尺寸时接触压力等参量的变化规律。分析得知缩口量变化对各监测量影响最大,其次是插孔簧片长度和厚度,开槽宽度对接触件的影响很小。结果表明,有限元法能较好地模拟接触件插拔过程中各监测量的变化情况。该方法能为电连接器接触件的设计和可靠性测试提供依据。

关键词: 电连接器接触件插拔特性有限元法仿真    
Abstract:

In order to find the changes of each monitoring measurement in the process of plug and pull of electrical connector contacts, concerning the influence of different structure parameters on plug and pull characteristic of electric connectors,the process of plug and pull was simulated by ANSYS. The changes of jack strip deformation, stress distribution, plug and pull force and contact force were surveyed, and the change law of contact force and other parameters was analysed with different structure size of the contact.The analysis showed that the variation of the shrinkage had the noticeable influence on each monitoring measurement followed by the jack strip length and thickness, and slot width had a little effect on the contact. The results showed that the finite element method could simulate the changes of the monitoring measurement in the process of plug and pull of contact preferably. The method can provide basis for the design and reliability test of electrical connector contact.

Key words: electrical connector    contact    plug and pull characteristic    finite element method    simulation
收稿日期: 2016-07-01 出版日期: 2017-04-28
CLC:  TM503.5  
基金资助:

国家自然科学基金资助项目(51107028);河北省高等学校创新团队领军人才培育计划资助项目(LJRC003)

作者简介: 骆燕燕(1971-),女,天津人,教授,博士生导师,从事电器可靠性研究,E-mail:luoyy@hebut.edu.cn,http://orcid.org//0000-0002-0847-2139
服务  
把本文推荐给朋友
加入引用管理器
E-mail Alert
RSS
作者相关文章  
骆燕燕
杨静宇
任永隆
张元磊
李文君

引用本文:

骆燕燕, 杨静宇, 任永隆, 张元磊, 李文君. 电连接器接触件插拔特性仿真与试验研究[J]. 工程设计学报, 2017, 24(2): 168-173,195.

LUO Yan-yan, YANG Jing-yu, REN Yong-long, ZHANG Yuan-lei, LI Wen-jun. Simulation and experimental study on plug and pull characteristic of electrical connector contact[J]. Chinese Journal of Engineering Design, 2017, 24(2): 168-173,195.

链接本文:

https://www.zjujournals.com/gcsjxb/CN/10.3785/j.issn.1006-754X.2017.02.007        https://www.zjujournals.com/gcsjxb/CN/Y2017/V24/I2/168

[1] 杨奋为.军用电连接器的应用及发展[J].机电元件,2007,27(3):42-49. YANG Fen-wei.Application and development of military electrical connectors[J]. Electromechanical Components, 2007, 27(3): 42-49.
[2] 林思达,潘骏,陈文华,等.电连接器可靠性研究述评[J].机电元件,2009,29(4):52-56. LIN Si-da, PAN Jun, CHEN Wen-hua, et al. An introductory review on reliability research of electrical connectors[J]. Electromechanical Components, 2009, 29(4): 52-56.
[3] 陈文华,李红石,连文志,等.航天电连接器环境综合应力加速寿命试验与统计分析[J].浙江大学学报(工学版),2006,40(2): 348-351. CHEN Wen-hua, LI Hong-shi, LIAN Wen-zhi, et al. Accelerated life test and statistical analysis of aerospace electrical connectors under multiple environmental stresses[J]. Journal of Zhejiang University (Engineering Science), 2006, 40(2): 348-351.
[4] 潘骏,靳方建,陈文华,等. 电连接器接触件结构分析与插拔试验[J]. 中国机械工程,2013,24(12):1636-1641. PAN Jun, JIN Fang-jian, CHEN Wen-hua, et al. Structural analysis of electrical connector contacts and insertion-extraction test[J]. China Mechanical Engineering, 2013, 24(12):1636-1641.
[5] 靳方建.电连接器接触件可靠性分析与高温插拔试验[D].杭州:浙江理工大学机械与自动控制学院,2013:33-45. JIN Fang-jian. Reliability analysis of electrical connector contacts and insertion-extraction test under high temperature[D]. Hangzhou:Zhejiang Sci-Tech University, School of Mechanical Engineering and Automation, 2013: 33-45.
[6] 许成彬,潘骏,陈文华,等.高温电连接器有限元热分析与接触件插拔试验[J].工程设计学报,2015,22(3):250-255. XU Cheng-bin, PAN Jun, CHEN Wen-hua, et al. Finite element thermal analysis and plugging test of the high temperature electrical connector[J]. Chinese Journal of Engineering Design, 2015, 22(3): 250-255.
[7] 樊薇薇,翟国富.航天电磁继电器簧片结构应力特性分析[J].机电元件,2007,27(2):7-12. FAN Wei-wei, ZHAI Guo-fu. Structural stress characteristics of the space electromagnetic relay spring[J]. Electromechanical Components, 2007, 27(2): 7-12.
[8] HORN J, EGENOLF B. Shape optimization of connector contacts for reduced wear and reduced insertion force[J].AMP Journal of Technology, 1992, 2: 42-46.
[9] SAWCHYN I, SPROLES E J. Optimizing force and geometry parameters in design of reduced insertion force connectors[J]. IEEE Transactions on Components, Hybrids, and Manufacturing Technology, 1992,15(6):1025-1033.
[10] JENNIFER L B. Structural design of an innovative electrical connector for satellite test of the equivalence Principle[D]. Sheffield: The University of Sheffield, Department of Mechanical Engineering, 2008: 45-55.
[11] Lü Bin, ZHOU Sheng-jun, ZHAO Lan-yan, et al. Technical research on optimization design of contacts of electrical connector[J].Journal of Zhejiang University (SCIENCE A), 2007, 8(3): 506-510.
[12] BELOUFA A. Numerical and experimental optimization of mechanical stress, contact temperature and electrical contact resistance of power automotive connector[J]. International Journal of Mechanics, 2010, 4(4): 94-104.
[13] SANTOSH V A, EBERETT W W, JACKSON R L, et al. A multi-physics finite element model of an electrical connector considering rough surface contact. Electrical Contacts[C]//Proceedings of the 54th IEEE Holm Conference on Electrical Contacts. Orlando, Oct.27-29, 2008.
[14] SANTOSH V A, ROBERT L J, SONG-yul Choe, et al. A multiphysics finite element model of a 35A automotive connector including multiscale rough surface contact[J]. Journal of Electronic Defense, 2012, 33(3):55-56.
[15] 刘鸿文. 材料力学[M]. 北京:高等教育出版社,2004:102-115. LIU Hong-wen.Material mechanics [M].Beijing: Higher Education Press, 2004: 102-115.
[16] 秦大同,谢里阳. 现代机械设计手册[M]. 北京:化学工业出版社,2011:103-115. QIN Da-tong,XIE Li-yang.Modern mechanical design handbook[M].Beijing: Chemical Industry Press, 2011: 103-115.
[17] 刘笑天. ANSYS Workbench 结构工程高级应用[M].北京:中国水利水电出版社,2015:43-61. LIU Xiao-tian.ANSYS workbench structural engineering advanced applications [M].Beijing: China Water & Power Press, 2015: 43-61.
[18] 刘永刚,申学良. 电连接器常用接触件设计概要[J]. 机电元件,2016,36(1):52-57. LIU Yong-gang,SHEN Xue-liang.Design overview of common electrical connector contacts[J].Electromechanical Components, 2016, 36(1): 52-57.
[1] 赵迪,陈果,陈小利,王熊锦. 轮式搜救机器人地形自适应机构设计及越障性能分析[J]. 工程设计学报, 2023, 30(5): 579-589.
[2] 王柏村,朱凯凌,鲍劲松,王峰,谢海波,杨华勇. 基于数字底座的涂装车身缓存区智能设计与调度优化[J]. 工程设计学报, 2023, 30(4): 399-408.
[3] 谢章伟,张兴波,徐哲,张羽,张丰云,王茜,王萍萍,孙树峰,王海涛,刘纪新,孙维丽,曹爱霞. 基于数字孪生的激光加工零件表面温度监控系统的构建[J]. 工程设计学报, 2023, 30(4): 409-418.
[4] 谢博伟,金莫辉,杨洲,段洁利,屈明宇,李锦辉. 3D打印TPU材料的力学性能及模型参数研究[J]. 工程设计学报, 2023, 30(4): 419-428.
[5] 张栋,杨培,黄哲轩,孙凌宇,张明路. 爬壁机器人悬摆式磁吸附机构的设计与优化[J]. 工程设计学报, 2023, 30(3): 334-341.
[6] 郭鸿杰,梁淑雅,陈文华,钟立强,陈哲文,颜佳辉. 线簧丝倾角对线簧孔式电连接器贮存寿命的影响研究[J]. 工程设计学报, 2023, 30(3): 390-398.
[7] 李洋波,蔡改贫,阮辽. 对辊破碎机对钨矿石的层压破碎特性研究[J]. 工程设计学报, 2023, 30(2): 212-225.
[8] 徐诗洋,吴炳晖,纪冬梅,戴新宇. 电力隧道自动巡检机器人设计与运动仿真[J]. 工程设计学报, 2023, 30(1): 32-38.
[9] 李毅,陈国华,夏铭,李波. 电主轴冷却系统设计与仿真优化[J]. 工程设计学报, 2023, 30(1): 39-47.
[10] 芮宏斌,李路路,王天赐,段凯文. 两栖仿海龟机器人动力学建模与运动控制研究[J]. 工程设计学报, 2023, 30(1): 73-81.
[11] 涂文兵,袁晓文,杨锦雯,杨本梦. 不同元件故障状态下滚动轴承的动态特性研究[J]. 工程设计学报, 2023, 30(1): 82-92.
[12] 张旭,赖磊捷,朱利民. 超精密大行程麦克斯韦磁阻驱动器磁场建模与推力分析[J]. 工程设计学报, 2022, 29(6): 748-756.
[13] 李科军,陈淼林,王江银,姚学军,邓旻涯,高龙. 湿喷机液压制动系统制动阀性能研究[J]. 工程设计学报, 2022, 29(5): 579-586.
[14] 唐绍禹,吴杰,张辉,邓兵兵,黄禹铭,黄浩. 多极式磁流变离合器温度场仿真与实验研究[J]. 工程设计学报, 2022, 29(4): 484-492.
[15] 李科军,邓旻涯,黄文静,张宇,曾家旺,陈淼林. 混凝土湿喷机摆动系统工作特性研究[J]. 工程设计学报, 2022, 29(4): 519-526.