Please wait a minute...
工程设计学报  2010, Vol. 17 Issue (3): 190-195    
工程设计理论、方法与技术     
基于有限元分析的高精密柔性夹具优化方案设计
 刘东红1, 赵建才2, 张翊翔2
1.台州广播电视大学 工程技术系, 浙江 台州 318000;2.上海交通大学 机械与动力学院, 上海 200240
The optimum design of highprecision flexible fixture based on finite element analysis
 LIU  Dong-Hong1, ZHAO  Jian-Cai2, ZHANG  Yi-Xiang2
1. College of Engineering and Technology, Taizhou Radio and TV University, Taizhou 318000, China;
2. School of Mechanical Engineering, Shanghai Jiaotong University, Shanghai 200240, China
 全文: PDF(1424 KB)   HTML
摘要: 针对高精密加工过程中柔性夹具的变形问题进行理论计算和实验分析.首先应用CAE软件对现有柔性夹具进行有限元分析,分析夹具变形问题.然后通过CAD软件改变该夹具模型的结构参数和尺寸参数,优化夹具构造,以减少定位过程的夹具变形,并再次通过CAE软件进行分析,验证优化效果.通过增加夹具体主平面刚度、增加夹具体肋板刚度和改变夹具定位点位置等方法,实现夹具体的最大变形量满足加工精度的要求.实验分析以定位点变形为研究对象,测量得到4个定位点在夹具装夹过程中的变形量.实验结果基本符合理论计算结果,得到最终优化方案的4个定位点变形量均小于001 mm,满足了该高精密加工中对夹具体的精度要求.优化方案在实际生产中得到实施,效果良好.
关键词: 高精密加工柔性夹具数字化设计有限元分析夹具变形    
Abstract: The theoretical calculation and experimental analysis have been done to solve the deformation problem of flexible fixture in the process of high-precision machining. First of all, the deformation of the existing flexible fixture had been analyzed using the CAE software. And then, the structure of fixture had been optimized by changing the parameters of the structure and dimension of fixture using the CAD software to reduce the deformation of the fixture in the process of positioning. To verify the effect of optimization, the deformation of the optimized fixture had been analyzed using the CAE software once again. The calculation results showed that, in order to ensure the maximum deformation to satisfy the machining accuracy requirements, many measures could be taken, such as increasing the stiffness of the principal plane, increasing the stiffness of the ribbed slab and changing the locating points of the fixture, and so on. Finally, the deformations of the locating points of the fixture were analyzed by experiments. The deformation of four points in the clamping process are less than 001 mm, which meets the accuracy requirement in the high-precision machining. The experimental results are basically in line with theoretical results. The optimized scheme has a good effect in producing process.
Key words:  high-precision machining    flexible fixture    digital design    finite element analysis (FEA)    fixture deformation
出版日期: 2010-06-28
:  TG 333  
服务  
把本文推荐给朋友
加入引用管理器
E-mail Alert
RSS
作者相关文章  
刘东红
赵建才
张翊翔

引用本文:

刘东红, 赵建才, 张翊翔. 基于有限元分析的高精密柔性夹具优化方案设计[J]. 工程设计学报, 2010, 17(3): 190-195.

LIU Dong-Hong, ZHAO Jian-Cai, ZHANG Yi-Xiang. The optimum design of highprecision flexible fixture based on finite element analysis[J]. Chinese Journal of Engineering Design, 2010, 17(3): 190-195.

链接本文:

https://www.zjujournals.com/gcsjxb/CN/        https://www.zjujournals.com/gcsjxb/CN/Y2010/V17/I3/190

[1] 谢超,陈云壮,石光楠,赖磊捷. 正交簧片型大行程柔性球铰设计及柔度分析[J]. 工程设计学报, 2023, 30(5): 626-633.
[2] 张涛,王开松,唐威,秦可成,刘阳,石雨豪,邹俊. 电流体泵驱动的柔性弯曲执行器的设计及分析[J]. 工程设计学报, 2023, 30(4): 467-475.
[3] 李琴,闫瑞,黄志强,李刚. 电驱可控震源驱动电机匹配设计与优化研究[J]. 工程设计学报, 2023, 30(2): 172-181.
[4] 李三平,孙腾佳,袁龙强,吴立国. 气动软体采摘机械手设计及实验研究[J]. 工程设计学报, 2022, 29(6): 684-694.
[5] 赵致勃,顾大强,李立新,张靖. 基于接触应力优化的摆线轮修形设计[J]. 工程设计学报, 2022, 29(6): 713-719.
[6] 张正峰,宋小雨,袁晓磊,陈文娟,张伟东. Al/CFRP混合薄壁结构耐撞性能可靠性优化设计[J]. 工程设计学报, 2022, 29(6): 720-730.
[7] 孙光明,王奕苗,万仟,弓堃,汪文津,赵坚. 考虑装配变形的精密机床床身优化设计[J]. 工程设计学报, 2022, 29(3): 318-326.
[8] 丰飞,傅雨晨,范伟,马举. 三角混合两级杠杆微位移放大机构的设计及性能分析[J]. 工程设计学报, 2022, 29(2): 161-167.
[9] 陈洪月, 张站立, 吕掌权. 线性压缩机圆柱臂盘簧的设计及性能研究[J]. 工程设计学报, 2021, 28(4): 504-510.
[10] 王成军, 李帅. 三关节式软体驱动器的设计及其弯曲性能分析[J]. 工程设计学报, 2021, 28(2): 227-234.
[11] 黄伟, 徐建, 陆新征, 胡明祎, 廖文杰. 动力装备和建筑楼盖的动力吸振研究[J]. 工程设计学报, 2021, 28(1): 25-32.
[12] 周超, 秦瑞江, 芮晓明. 风载荷作用下V形绝缘子串的力学特性分析[J]. 工程设计学报, 2021, 28(1): 95-104.
[13] 周超, 王阳, 芮晓明. 500 kV输电线路跳线风偏有限元分析与试验研究[J]. 工程设计学报, 2020, 27(6): 713-719.
[14] 李成兵, 雷鹏. 5 000 m3立式拱顶储罐应力分析与弱顶性能评价[J]. 工程设计学报, 2020, 27(2): 182-190.
[15] 刘召, 由宏新, 孙亮, 杨玉玲, 刘华清. 大型球罐悬吊式液压传动回转检测平台设计[J]. 工程设计学报, 2019, 26(3): 267-273.