Please wait a minute...
工程设计学报
工程设计学报  2017, Vol. 24 Issue (4): 412-417    DOI: 10.3785/j.issn.1006-754X.2017.04.007
建模、分析、优化和决策     
PMSM馈能系统硬件在环仿真研究
邓涛, 周豪, 李军营
重庆交通大学 机电与车辆工程学院, 重庆 400074
Hardware-in-the-loop simulation research for PMSM energy feedback system
DENG Tao, ZHOU Hao, LI Jun-ying
School of Mechatronics & Vehicle Engineering, Chongqing Jiaotong University, Chongqing 400074, China
 全文: PDF(4141 KB)   HTML
摘要：

为对电动汽车动力电机馈能效率进行研究，方便馈能效率的测量，提出一种基于滑模控制算法的PMSM（permanent magnet synchronous motor）馈能研究方法，即通过控制电动机的输入电压与电流来驱动相同性能的电动机发电。首先以馈能理论为基础，建立包含滑模变结构控制、空间矢量、PMSM等模块的PMSM馈能系统仿真模型，并进行离线仿真分析。结果表明：采用所提出的馈能方法可达到70%左右的馈能效率，具有一定的可行性。同时，建立PMSM馈能系统dSPACE硬件在环试验平台，对其进行硬件在环试验验证。试验结果表明：电动机馈能效率在60%~80%的范围内，与离线仿真所得结果较为接近。这不仅验证了所建立的馈能仿真模型的正确性，且进一步证明了纯电动汽车动力电机自身馈能在节能方面的可行性。所提出的馈能方法能够为目前现有馈能方式提供更多选择，硬件在环试验研究也能够为后续的PMSM台架和实车试验研究提供一些技术支持。
关键词： PMSM;  馈能;  滑模控制;  仿真;  硬件在环    
Abstract:

In order to study the feedback efficiency of driving motor for electric vehicle and test the feedback efficiency expediently,the PMSM (permanent magnet synchronous motor) energy feed-back system based on sliding mode control algorithm is proposed.It can control the input voltage and current to drive another motor with the same features to generate.Based on the theory of en-ergy feedback,the energy feedback simulation model for PMSM driving system was established, which consisted of the sliding mode and variable structure control block,the space vector block and the PMSM numerical simulation model.And then,the energy feedback simulation model for PMSM system was simulated and analyzed.The simulation results showed that the proposed en-ergy feedback method could obtain about 70% feedback efficiency.That's meant that the pro-posed energy feedback method was feasible.Then,the hardware-in-the-loop (HIL) test system with dSPACE controller for PMSM energy feedback was built.The proposed energy feedback method was verified by the hardware-in-the-loop (HIL) test system.The test results showed that the obtained feedback efficiency was 60% 80%.The test value was very close to the offline simu-lation value.Obviously, the test results not only verify the accuracy of energy feedback simulation model for PMSM,but also prove the feasibility of the energy feedback for the driving motor of electric vehicle.In addition,the proposed energy feedback method can provide more choices for current energy feedback mode.And,the hardware-in-the-loop test system also can provide some technology support for PMSM platform test and real-vehicle test research.
Key words: PMSM    energy feedback    sliding mode control    simulation    hardware-in-the-loop
收稿日期: 2017-01-16 出版日期: 2017-08-28
CLC:  U462.2  
基金资助:

国家自然科学基金资助项目（51305473）；中国博士后科学基金资助项目（2014M552317）；重庆市博士后研究人员科研项目（xm2014032）；重庆市基础与前沿研究计划项目（cstc2014jcyjA60006）
作者简介: 邓涛(1982-),男,江西新干人,教授,博士,从事新能源车辆理论及应用研究,E-mail:d82t722@cqjtu.edu.cn,http://orcid.org/0000-0001-6881-9854
服务　　
把本文推荐给朋友
加入引用管理器
E-mail Alert
RSS
作者相关文章　　
邓涛
周豪
李军营

引用本文:

邓涛, 周豪, 李军营. PMSM馈能系统硬件在环仿真研究[J]. 工程设计学报, 2017, 24(4): 412-417.

DENG Tao, ZHOU Hao, LI Jun-ying. Hardware-in-the-loop simulation research for PMSM energy feedback system[J]. Chinese Journal of Engineering Design, 2017, 24(4): 412-417.

链接本文:

https://www.zjujournals.com/gcsjxb/CN/10.3785/j.issn.1006-754X.2017.04.007    或    https://www.zjujournals.com/gcsjxb/CN/Y2017/V24/I4/412

[1] 黄昆,张勇超,喻凡,等. 电动式主动馈能悬架综合性能的协调性优化[J].上海交通大学学报,2009,43(2):226-230. HUANG Kun, ZHANG Yong-chao, YU Fan, et al. Coordinate optimization for synthetical performance of electrical energy-regenerative active suspension[J].Jour-nal of Shanghai Jiaotong University, 2009, 43(2):226-230.
[2] 于长淼,王伟华,王庆年.电磁馈能式悬架方案设计与节能分析[J].汽车技术,2010(2):21-25. YU Chang-miao,WANG Wei-hua,WANG Qing-nian.De-sign of electromagnetic energy regenerative suspension system and analysis of energy conservation[J].Automobile Technology,2010(2):21-25.
[3] 王科星.汽车馈能式悬架技术研究[J]. 轻型汽车技术, 2010(11/12):7-10. WANG Ke-xing.Study on the technology of automobile energy feed suspension[J].Light Vehicles,2010(11/12):7-10.
[4] 刘松山,王庆年,王伟华.电磁馈能悬架非线性阻尼特性仿真分析[J].汽车工程,2014,36(12):1528-1533. LIU Song-shan,WANG Qing-nian,WANG Wei-hua.A simulation analysis on the nonlinear damping character-istics of electromagnetic regenerative suspension[J]. Automotive Engineering,2014,36(12):1528-1533.
[5] 陈士安,何仁,陆森林.馈能型悬架的仿真与性能评价研究[J].汽车工程,2008,28(2):167-171. CHEN Shi-an, HE Ren,LU Sen-lin.A study on the simulation of energy reclaiming suspension and perform -ance evaluation[J].Automotive Engineering,2008,28(2):167-171.
[6] 王伟华,李志成,于长淼.一种新型汽车馈能减振器的结构设计与特性分析[J].汽车技术,2010(3):44-50. WANG Wei-hua,LI Zhi-cheng,YU Chang-miao.Struc-ture design and characteristics analysis of a new type of automotive regenerative shock[J].Automobile Technol-ogy,2010(3):44-50.
[7] ŠIMÁNEK J,NOVÁK J,DOLE ? EK R.Control algo-rithms for permanent magnet synchronous traction motor[C]//The International Computer Conference, Eurocon:IEEE Computer Society Press, 2007:1839-1844.
[8] 刘军.基于滑模观测器的PMSM无位置传感器矢量控制的研究[D].杭州:浙江大学电气工程学院,2014:20-36. LIU Jun. Research of sensorless vector control for PMSM based on sliding mode observer[D].Hangzhou:Zhejiang University,College of Electrical Engineering, 2014:20-36.
[9] PAPONEN K,KONGHIRUN M.An improved sliding mode observer for speed sensorless vector control drive of PMSM[C]//CES/IEEE 5th International Power E-lectronics and Motion Control Conference, Shanghai, Aug.14-16,2006.
[10] LIU Jia-xi,YANG Gui-jie,YAN Peng-fei.Rotor posi-tion estimation for PMSM based on sliding mode ob-server[C]//The International Conference on Mecha-tronics and Automation,Harbin,Aug.5-8,2007.
[11] 严萍,刘国平,李建武.基于dSPACE平台梯形速度的PID控制模型建立及实验[J].机械设计与制造,2010(9):185-186. YAN Ping,LIU Guo-ping,LI Jian-wu.The PID model for trapezoid speed curves design and experiment with dSPACE controller[J].Machinery Design & Manufac-ture,2010(9):185-186.
[12] WEI D Q,LUO X S,WANG B H,et al.Robust a-daptive dynamic surface control of chaos in permanent magnet synchronous motor[J].Physics Letters A, 2007,363(1/2):71-77.
[13] 周志敏.开关电源实用技术:设计与应用[M].2版.北京:人民邮电出版社,2007:2-300. ZHOU Zhi-min.Design and application of switching power supply technology[M].2th ed.Beijing:People's Posts and Telecommunications Press,2007:2-300.
[14] DARREN Ashby.电子电气工程师必知必会[M].2版. 尹华杰,译.北京:人民邮电出版社,2010:40-212. DARREN Ashby.Electrical and electronic engineers must know[M].2th ed.Translated by YIN Hua-jie. Beijing:People's Posts and Telecommunications Press,2010:40-212.
[15] 陈南虎,李建刚.基于dSPACE的运动控制仿真平台设计[J].微计算机信息,2008,24(11):258-260. CHEN Nan-hu, LI Jian-gang.Design of a motion control simulation platform configured with dSPACE controller[J].Microcomputer Information,2008,24(11):258-260.
[16] KAWAMOTO Y, SUDA Y, INOUE H, et al. Modeling of electromagnetic damper for automobile suspension[J].Journal of System Design and Dynamics,2007,1(3):524-535.
[1] 赵迪,陈果,陈小利,王熊锦. 轮式搜救机器人地形自适应机构设计及越障性能分析[J]. 工程设计学报, 2023, 30(5): 579-589.
[2] 余乐,侯勇俊,赵永强,汪玉琪. 双异步电机驱动双质体振动系统同步滑模控制[J]. 工程设计学报, 2023, 30(5): 608-616.
[3] 王柏村,朱凯凌,鲍劲松,王峰,谢海波,杨华勇. 基于数字底座的涂装车身缓存区智能设计与调度优化[J]. 工程设计学报, 2023, 30(4): 399-408.
[4] 谢章伟,张兴波,徐哲,张羽,张丰云,王茜,王萍萍,孙树峰,王海涛,刘纪新,孙维丽,曹爱霞. 基于数字孪生的激光加工零件表面温度监控系统的构建[J]. 工程设计学报, 2023, 30(4): 409-418.
[5] 谢博伟,金莫辉,杨洲,段洁利,屈明宇,李锦辉. 3D打印TPU材料的力学性能及模型参数研究[J]. 工程设计学报, 2023, 30(4): 419-428.
[6] 何育民,韩莹,周晶. 基于改进果蝇优化算法的塔机自适应滑模控制研究[J]. 工程设计学报, 2023, 30(3): 271-280.
[7] 张栋,杨培,黄哲轩,孙凌宇,张明路. 爬壁机器人悬摆式磁吸附机构的设计与优化[J]. 工程设计学报, 2023, 30(3): 334-341.
[8] 李洋波,蔡改贫,阮辽. 对辊破碎机对钨矿石的层压破碎特性研究[J]. 工程设计学报, 2023, 30(2): 212-225.
[9] 徐诗洋,吴炳晖,纪冬梅,戴新宇. 电力隧道自动巡检机器人设计与运动仿真[J]. 工程设计学报, 2023, 30(1): 32-38.
[10] 李毅,陈国华,夏铭,李波. 电主轴冷却系统设计与仿真优化[J]. 工程设计学报, 2023, 30(1): 39-47.
[11] 芮宏斌,李路路,王天赐,段凯文. 两栖仿海龟机器人动力学建模与运动控制研究[J]. 工程设计学报, 2023, 30(1): 73-81.
[12] 涂文兵,袁晓文,杨锦雯,杨本梦. 不同元件故障状态下滚动轴承的动态特性研究[J]. 工程设计学报, 2023, 30(1): 82-92.
[13] 张旭,赖磊捷,朱利民. 超精密大行程麦克斯韦磁阻驱动器磁场建模与推力分析[J]. 工程设计学报, 2022, 29(6): 748-756.
[14] 李科军,陈淼林,王江银,姚学军,邓旻涯,高龙. 湿喷机液压制动系统制动阀性能研究[J]. 工程设计学报, 2022, 29(5): 579-586.
[15] 唐绍禹,吴杰,张辉,邓兵兵,黄禹铭,黄浩. 多极式磁流变离合器温度场仿真与实验研究[J]. 工程设计学报, 2022, 29(4): 484-492.