Please wait a minute...
浙江大学学报(工学版)
J4  2013, Vol. 47 Issue (2): 193-200    DOI: 10.3785/j.issn.1008-973X.2013.02.001
机械工程     
先导式电液配流系统的动态特性
朱旭, 魏建华, 方锦辉
浙江大学 流体动力及机电系统国家重点实验室, 浙江 杭州 310027
Dynamic characteristics of pilot-operated electro-hydraulic
flow distribution system
ZHU Xu, WEI Jian-hua, FANG Jin-hui
State Key Laboratory of Fluid Power Transmission and Control, Zhejiang University, Hangzhou 310027, China
 全文: PDF  HTML
摘要：

为了实现往复式压缩机排气量的无级调节,满足气量调节对配流过程响应快速性和平稳性的要求,提出一种基于双阀结构的先导式电液配流系统.建立压缩机吸气和回流过程中的配流气阀动力学模型,通过联合仿真研究主要设计参数对电液配流系统动态特性的影响.研究结果表明：电液执行机构的压力飞升和卸压速率是影响气阀动作快慢的关键因素；所设计的配流系统中气阀开启和关闭滞后时间均小于10 ms,气阀响应速度显著提高；供油压力10 MPa、阀片行程2 mm条件下阀片与阀座和行程限制器的撞击速度分别为0.214和1.35 m/s,充分满足可靠性许用要求；气阀动作试验曲线与仿真结果拟合程度高,所述联合仿真模型可以作为电液配流系统性能分析的研究平台.
Abstract:

A novel pilot-operated electro-hydraulic flow distribution system based on a double-valve structure was proposed for the stepless capacity control of reciprocating compressors, satisfying the requirements of response speed and stability for flow distribution in capacity control. A dynamic mathematical model of distributing valve for the compressor suction and backflow process was established. The influence of main design parameters on the dynamic characteristics of flow distribution system was investigated by co-simulation. The results indicate that the rates of actuator pressure rise and discharge are most important for the response speed of distributing valve. Under normal conditions of proposed electro-hydraulic flow distribution system, the response speed of suction valve increases significantly with opening time and closing time that are both less than 10 ms. The impact velocities of distributing valve plate between valve seat and valve guard are 0.214 and 1.35 m/s respectively with 10 MPa oil pressure and 2 mm valve stroke, which can fully meet the requirements for reliable operation. The motion curves of suction valve accord well with the simulation, suggesting that the co-simulation model is quite suitable for the performance analysis of electro-hydraulic flow distribution system.
出版日期: 2013-02-01
:  TH 137  
基金资助:

国家自然科学基金资助项目(50575201).
通讯作者: 魏建华,男,教授,博导.     E-mail: jhwei@zju.edu.cn
作者简介: 朱旭(1984－),男,博士生,从事电液比例/伺服控制方面的研究.E-mail: zhuxu.17@163.com
服务　　
把本文推荐给朋友
加入引用管理器
E-mail Alert
RSS
作者相关文章　　

引用本文:

朱旭, 魏建华, 方锦辉. 先导式电液配流系统的动态特性[J]. J4, 2013, 47(2): 193-200.

ZHU Xu, WEI Jian-hua, FANG Jin-hui. Dynamic characteristics of pilot-operated electro-hydraulic
flow distribution system. J4, 2013, 47(2): 193-200.

链接本文:

http://www.zjujournals.com/eng/CN/10.3785/j.issn.1008-973X.2013.02.001    或    http://www.zjujournals.com/eng/CN/Y2013/V47/I2/193

［1］ STEINRUCK P, OTTITSCH P, OBERHUBER A. Better reciprocating compressor capacity control ［J］. Hydrocarbon Processing, 1997, 76(2): 79-83.
［2］ DANNY M D, ANTHONY J S, KLAUS B, et al. Advanced reciprocating compression technology ［R］. No.18. 11052, San Antonio: Southwest Research Institute Report, 2005.
［3］ 洪伟荣,吴荣仁,金江明.一种基于时间控制顶开活塞压缩机进气阀的装置:中国,200610155395.8［P］. 20070627.
HONG Wei-rong, WU Rong-ren, JIN Jiangming. Equipment based on time controlled depressed suction valve of reciprocating compressors: China, 200610155395.8［P］. 20070627.
［4］ JIN Jiang-ming, HONG Wei-rong, TANG Lin-bo. Improved stepless capacity regulation for reciprocating compressors ［J］. Hydrocarbon Processing, 2009, 8: 43-47.
［5］ 唐斌,李连生,王乐.往复式压缩机气量无级调节过程中进气阀的动态研究［J］.机械工程学报,2011, 47(4): 136-141.
TANG Bin, LI Lian-sheng, WANG Le. Dynamic analysis of valve with stepless capacity control for reciprocating compressor ［J］. Journal of Mechanical Engineering, 2011, 47(4): 136-141.
［6］ GU Zhao-Lin, HOU Xiong-Po, WANG Zan-she, et al. Methods for large reciprocating compressor capacity control: A review based on pulse signal concept ［J］. Chinese Science Bulletin, 2011, 56(19): 1967-1974.
［7］ 唐崇茂.高速开关阀控制的插装阀及其在冲床油路系统中的应用研究［D］.长沙:中南大学,2009.
TANG Chongmao. Research of high speed on/off valve controlled logic valve and application in hydraulic punch system ［D］. Changsha: Zhongnan University, 2009.
［8］ 石延平,刘成文,张永忠.一种大流量高速开关阀的研究与设计［J］.机械工程学报,2004, 40(4): 195-198.
SHI Yan-ping, LIU Cheng-wen, ZHANG Yong-zhong. Design and study of a new kind of larger flow rate high-speed on-off valve ［J］. Chinese Journal of Mechanical Engineering, 2004, 40(4): 195-198.
［9］ 金江明.活塞式压缩机排气量无级调节系统关键技术的研究［D］.杭州: 浙江大学, 2010.
JIN Jiangming. Key technology research on stepless capacity regulation system for reciprocating compressor ［D］. Hangzhou: Zhejiang University, 2010.
［10］ 吴业正.往复式压缩机数学模型及应用［M］.西安:西安交通大学出版社,1989: 29-33.
［11］ 林梅,吴业正.压缩机自动阀［M］.西安:西安交通大学出版社,1991:94-95.
[1] 丁川,丁凡,周星,满在朋,杨灿军. 新型耐压湿式比例电磁铁的研制与对比试验研究[J]. J4, 2014, 48(3): 451-455.
[2] 宋月超, 徐兵, 杨华勇, 张军辉. 改进的柱塞泵流量脉动“实用近似”测试法[J]. J4, 2014, 48(2): 200-205.
[3] 满在朋,丁凡,丁川,刘硕,黄挺峰. 液压软管脉冲试验的发展与研究综述[J]. J4, 2014, 48(1): 21-28.
[4] 施虎, 杨华勇, 龚国芳, 侯典清. 盾构推进液压系统载荷顺应性指标和评价方法[J]. J4, 2013, 47(8): 1444-1449.
[5] 侯典清,龚国芳,施虎,王林涛. 基于顺应特性的新型盾构推进系统设计[J]. J4, 2013, 47(7): 1287-1292.
[6] 施虎,杨华勇,龚国芳,王林涛. 盾构掘进机关键技术及模拟试验台现状与展望[J]. J4, 2013, 47(5): 741-749.
[7] 魏建华,国凯,熊义. 大型装备多轴电液执行器同步控制[J]. J4, 2013, 47(5): 755-760.
[8] 侯典清, 龚国芳, 施虎, 王林涛. 盾构推进系统突变载荷顺应特性研究[J]. J4, 2013, 47(3): 522-527.
[9] 张彦廷, 渠迎锋, 刘振东, 马江涛. 天车升沉补偿系统摇摆装置的设计[J]. J4, 2012, 46(12): 2268-2273.
[10] 方锦辉, 魏建华, 孔晓武. 并联伺服阀的同步控制策略[J]. J4, 2012, 46(6): 1054-1059.
[11] 杜恒, 魏建华, 冯瑞琳. 压力跟踪阀建模、仿真与试验研究[J]. J4, 2012, 46(6): 1034-1040.
[12] 满军, 丁凡, 李其朋, 笪靖, 邵森寅. 永磁屏蔽式耐高压高速开关电磁铁[J]. J4, 2012, 46(2): 309-314.
[13] 管成,徐晓,林潇,王守洪. 液压挖掘机回转制动能量回收系统[J]. J4, 2012, 46(1): 142-149.
[14] 黄家海,邱敏秀,方文敏. 液黏调速离合器中摩擦副间隙内流体传热分析[J]. J4, 2011, 45(11): 1934-1940.
[15] 黄家海,魏建华,邱敏秀. 液黏调速离合器传动特性分析[J]. J4, 2011, 45(11): 1927-1933.