Please wait a minute...
工程设计学报
工程设计学报  2016, Vol. 23 Issue (3): 228-234    DOI: 10.3785/j.issn. 1006-754X.2016.03.006
建模、分析、优化和决策     
激励与滚筒振动耦合下采煤机动力学特性分析
陈洪月1, 刘烈北1, 毛君1, 宋秋爽2, 袁智2
1. 辽宁工程技术大学 机械工程学院, 辽宁 阜新 123000;
2. 中国煤矿装备有限责任公司, 北京 100011
The analysis of the shearer dynamic feature in the coupling relation between the the motivation and the drum vibration
CHEN Hong-yue1, LIU Lie-bei1, MAO Jun1, SONG Qiu-shuang2, YUAN Zhi2
1. College of Mechanical Engineering, Liaoning Technical University, Fuxin 123000, China;
2. China National Coal Mining Equipment Co., Ltd., Beijing 100011, China
 全文: PDF(2737 KB)   HTML
摘要：

为了研究采煤机截割过程中的动力学特性及其对截割载荷的影响,采用含滚筒振动量的锋利截齿截割阻力模型描述滚筒截割载荷,采用含间隙齿轮啮合模型描述行走轮驱动载荷,采用库伦摩擦模型描述平滑靴摩擦载荷,建立了采煤机整机五自由度动力学模型,利用ode45对模型求解.结果表明:当煤岩硬度f=3,行走速度为3 m/min时,采煤机右摇臂振动幅值约为0.8×10-4rad,左摇臂振动幅值约为0.4×10-5rad;机身振动速度在-1.4~+1.4 mm/s间波动,右、左摇臂的振动角速度分别在-1×10-3~+1×10-3 rad/s和-4.5×10-4~+4.5×10-4 rad/s间波动;通过对比考虑滚筒振动和未考虑滚筒振动时的截割载荷,表明滚筒的振动有利于对煤岩的截割;对右侧摇臂的振动量进行了实验测量,其大小及波动范围与仿真值较为接近,说明采煤机的动力学模型具有一定的准确性.
关键词： 采煤机;  动态特性;  截割性能;  非线性;  实验研究    
Abstract:

In order to study the dynamic feature of shearer in the process of cutting and its influence on cutting load, the drum cutting loading was described by the sharp-pick cutting resistance model. The drive load of walking wheel was described by gear mesh model with clearance. The friction load of the smooth shoe was described by Coulomb friction model. The five degree freedom dynamics model of the shearer was established, which was solved by the method of ode45. The result showed that when the hardness of coal rock f=3 and the walking speed was 3 m/min, the vibration amplitude of the shearer's right arm was about 0.8×10-4 rad , the vibration amplitude of the left arm was about 0.4×10-5 rad; the vibration amplitude of the body was -1.4~+1.4 mm/s; the angular velocity of the right and left rocker arm was -1×10-3~+1×10-3 and -4.5×10-4~+4.5×10-4 rad/s. By comparing weather the drum vibration was considered, the result showed that the drum vibration was beneficial to the coal cutting. Through the experimental measurement of the right rocker arm vibration, it was found that the real value and the fluctuation range was basically the same. The result shows that the dynamic model of the shearer has certain accuracy.
Key words: shearer    dynamic feature    cutting performance    nonlinear    experimental research
收稿日期: 2015-06-05 出版日期: 2016-06-28
CLC:  TP421.5  
基金资助:

国家能源研发(实验)中心重大项目(2015_215).
作者简介: 陈洪月(1982-),男,辽宁海城人,副教授,博士,从事机械系统动力学分析与控制研究,E-mail:chyxiaobao@126.com.http://orcid.org//0000-0002-8458-3199
服务　　
把本文推荐给朋友
加入引用管理器
E-mail Alert
RSS
作者相关文章　　
陈洪月
刘烈北
毛君
宋秋爽
袁智

引用本文:

陈洪月, 刘烈北, 毛君, 宋秋爽, 袁智. 激励与滚筒振动耦合下采煤机动力学特性分析[J]. 工程设计学报, 2016, 23(3): 228-234.

CHEN Hong-yue, LIU Lie-bei, MAO Jun, SONG Qiu-shuang, YUAN Zhi. The analysis of the shearer dynamic feature in the coupling relation between the the motivation and the drum vibration. Chinese Journal of Engineering Design, 2016, 23(3): 228-234.

链接本文:

https://www.zjujournals.com/gcsjxb/CN/10.3785/j.issn. 1006-754X.2016.03.006    或    https://www.zjujournals.com/gcsjxb/CN/Y2016/V23/I3/228

[1] 张世洪.我国综采采煤机技术的创新研究[J].煤炭学报,2010,35(11):1988-1994. ZHANG Shi-hong.Study on the innovation of fully mechanized coal shearer technology in China[J].Journal of China Coal Society,2010,35(11):1988-1994.

[2] 赵丽娟,王乘云.采煤机截割部建模与动力学仿真研究[J].工程设计学报,2010,17(2):119-124. ZHAO Li-juan,WANG Cheng-yun.Modeling and dynamic simulation of shearer cutting unit [J].Chinese Journal of Engineering Design,2010,17(2):119-124.

[3] 赵丽娟,宋朋,谢波.新型薄煤层采煤机截割部振动特性研究[J].广西大学学报(自然科学版),2014,39(2):265-274. ZHAO Li-juan,SONG Peng,XIE Bo.Vibration performance research of a new shearer cutting unit in shin coal seam[J].Journal of Guangxi University (Natural Science Edition),2014,39(2):265-274.

[4] 廉自生,刘楷安.采煤机摇臂虚拟样机及其动力学分析[J].煤炭学报,2005,30(6):801-804. LIAN Zi-sheng,LIU Kai-an.Virtual proto type of shearer ranging arm and its dynamics analysis[J].Journal of China Coal Society,2005,30(6):801-804.

[5] 刘春生,李德根,戴淑芝.随机载荷对双滚筒采煤机整机力学特性的影响[J].煤矿机电,2012(6):45-49. LIU Chun-sheng,LI De-gen,DAI Shu-zhi.Fluency of random load on mechanical properties of double-drum shearer[J].Coal Mine Electromechanical,2012(6):45-49.

[6] 刘春生.滚筒式采煤机理论设计基础[M].徐州:中国矿业大学出版社,2003:85-90. LIU Chun-sheng.Design basis of drum shearer design theory[M].Xuzhou:China University of Mining and Technology Press,2003:85-90.

[7] 李晓豁,李萍,刘春生.采煤机在行走方向上的动力学行为研究[J].黑龙江科技学院学报,2002,12(4):1-4. Ll Xiao-huo,Ll Ping,LIU Chun-sheng.Study of shearer dynamic behaviors along the traction[J].Journal of Heilongjiang Institute of Science & Technology,2002,12(4):1-4.

[8] LIU Song-yong.Model test of the cutting properties of a shearer drum [J].Mining Science and Technology,2009,19(1):74-78.

[9] LIU Song-yong,LUO Chen-xu.Vibration experiment of shearer walking unit[J].Applied Mechanics & Materials,2012,268:1257-1261.

[10] 周甲伟,刘瑜,刘送永,等.采煤机行走机构动态啮合特性分析[J].工程设计学报,2013,20(3):230-237. ZHOU Jia-wei,LIU Yu,LIU Song-yong,et al.Characteristic analysis of dynamic meshing for shearer walking mechanism[J].Chinese Journal of Engineering Design,2013,20(3):230-237.

[11] LI Jian-ping, GUO Hui-zhen.Vibration characteristics of shearer cutting unit based on multibody dynamics[J].Electronic Journal of Geotechnical Engineering,2014,19(4):3195-3208.

[12] SEYED Hadi Hoseinie,MOHAMMAD Ataei,REZA Khalokakaie, et al.Reliability analysis of drum shearer machine at mechanized longwall mines[J].Journal of Quality in Maintenance Engineering,2012,18(1):98-119.

[13] TIRYAKI B.In situ studies on service life and pick consumption characteristics of shearer drums[J].Journal of the South African Institute of Mining and Metallurgy,2004,104(2):107-121.

[14] 单祖辉.材料力学[M].北京:高等教育出版社,2010:152-159. SHANG Zu-hui.Mechanics of materials[M].Beijing:Higher Education Press,2010:152-159.

[15] 盛冬平,朱如鹏,靳广虎,等.考虑摩擦的多间隙直齿弯扭振动建模和分岔特性[J].航空动力学报,2015,30(2):498-506. SHENG Dong-ping,ZHU Ru-peng,JIN Guang-hu,et al.Bifurcation characteristic and modeling of transverse-torsional spur gear vibration considering friction and multiple clearances[J].Journal of Aerospace Power,2015,30(2):498-506.

[16] 黄冠华,周宁,张卫华,等.动态激励下高速列车齿轮传动系统振动特性分析[J].铁道学报,2012,36(12):20-27. HUAN Guan-hua,ZHOU Ning,ZHANG Wei-hua,et al.Vibration characteristics of gear transmission system of high speed train under dynamic excitation[J].Journal of the China Railway Society,2012,36(12):20-27.
[1] 田助新,郭明慧,曹海印. 环形油腔液体静压推力轴承动态特性的影响因素研究[J]. 工程设计学报, 2022, 29(4): 456-464.
[2] 王学军,普江华,陈明方. 自动化生产线用同步带传动升降机的动态特性分析[J]. 工程设计学报, 2022, 29(2): 212-219.
[3] 胡坤, 蒋庆楠, 季晨光, 杨健, 李飞. 基于改进ESO的磁悬浮系统模型参考滑模控制[J]. 工程设计学报, 2022, 29(1): 82-91.
[4] 谢苗, 张保国, 王鹏飞, 李政. 基于相似理论的掘进机主动激振截割性能研究[J]. 工程设计学报, 2021, 28(5): 576-584.
[5] 白杨溪, 陈洪月, 陈洪岩, 王鑫, 李建刚. 基于滚筒载荷的采煤机滑靴振动分析及实验验证[J]. 工程设计学报, 2021, 28(3): 358-366.
[6] 黄龙艺, 王华, 嵇栩. 考虑紧固螺栓的三排滚柱式转盘轴承载荷分布计算[J]. 工程设计学报, 2021, 28(3): 350-357.
[7] 黄维, 刘惟伊, 刘志恩, 卢炽华. 基于多目标遗传算法的实验目标车底盘结构优化[J]. 工程设计学报, 2021, 28(1): 80-88.
[8] 王昕煜, 平雪良. 基于多传感器融合信息的移动机器人速度控制方法[J]. 工程设计学报, 2021, 28(1): 63-71.
[9] 张超, 韩晓明, 李强, 李池. 冲击载荷下永磁式电涡流减振器设计及动态特性分析[J]. 工程设计学报, 2020, 27(6): 786-794.
[10] 白杨溪, 陈洪月, 陈洪岩, 王鑫. 多约束条件下采煤机摇臂横向振动分析及试验验证[J]. 工程设计学报, 2020, 27(6): 707-712.
[11] 宋智斌, 胡秀棋. 基于给定非线性刚度的柔顺驱动器设计及性能评估[J]. 工程设计学报, 2020, 27(4): 416-424.
[12] 张卫东, 秦剑, 陈迪, 李其莹, 乔良, 孙国磊. 工作索耦合作用下多档多载荷货运索道的分析与计算方法[J]. 工程设计学报, 2020, 27(3): 293-300.
[13] 姜晓飞, 张冠伟, 胡永秀, 张大卫. 数控机床整机动态特性评价方法[J]. 工程设计学报, 2020, 27(2): 135-145.
[14] 张帅, 韩军, 涂群章, 杨小强, 杨旋. 基于GA-NLP的剪刀式折叠桥梁展桥机构多目标优化设计[J]. 工程设计学报, 2020, 27(1): 67-75.
[15] 孔垂旺, 陈为林, 卢清华, 罗陆锋, 张云志. 单级柔顺正交位移放大机构非线性建模与优化[J]. 工程设计学报, 2020, 27(1): 76-86.