Please wait a minute...
工程设计学报
工程设计学报  2016, Vol. 23 Issue (1): 54-59,81    DOI: 10.3785/j.issn.1006-754X.2016.01.009
建模、分析、优化和决策     
智能立体停车位框架的模态分析
毛君, 董先瑞, 谢苗, 闫江龙, 李翠
辽宁工程技术大学 机械工程学院, 辽宁 阜新 123000
Modal analysis of frame on intelligent stereo parking space
MAO Jun, DONG Xian-rui, XIE Miao, YAN Jiang-long, LI Cui
College of Mechanical Engineering, Liaoning Technical University, Fuxin 123000, China
 全文: PDF(2239 KB)   HTML
摘要： 随着经济的发展,家庭轿车保有量急剧上升,停车难的问题日益突出.提出了一种单边驱动立体框架智能停车位,介绍了智能立体停车位的结构和工作原理.利用拉格朗日方法建立了智能立体停车位框架多自由度振动系统的动力学模型并得到了自由振动频率方程.利用有限元分析软件ANSYS-workbench分析了无载和有载工况下立体停车位框架的固有频率和振型,指出了立体停车位框架的薄弱位置;进行了无载和有载工况下智能立体停车位框架锤击模态试验,验证智能立体停车位模态分析建模及仿真结果的正确性.研究表明,建立立体停车位框架多自由度振动系统的动力学模型和仿真模型是有效的.研究结果为停车位框架系统的进一步优化设计提供依据.
关键词： 立体停车位;  框架;  动力学模型;  模态分析    
Abstract: Along with the development of the economy, a sharp rise in the family car ownership, parking problem is becoming more and more prominent. A unilateral drive stereo frame intelligent parking was proposed, the structure and working principle of intelligent stereo parking space was introduced. The dynamics model of multi-degree freedom vibration system of intelligent stereo parking space framework was establish to obtain free vibration frequency equation by using Lagrange method. Through finite element analysis software ANSYS workbench, the inherent frequency and vibration model of stereo parking space with or without load and the weak position of stereo parking space framework were analyzed. For no-load and load conditions of intelligence stereo parking space frame, hammer modal test had been done, the correctness of modal analysis of the modeling and simulation results had been verified. Studies had shown that setting up dynamic model and simulation model of stereo parking space framework with multi-degree of freedom vibration system was effective. Research results provide the basis for parking space frame system of further optimization design.
Key words: stereo parking space    frame    dynamic model    modal analysis
收稿日期: 2015-05-06 出版日期: 2016-02-28
CLC:  TH113.1  
基金资助:

辽宁省教育厅科学研究一般项目(L2012118);辽宁省教育厅创新团队资助项目(LT2013009).
通讯作者: 董先瑞(1989-),硕士,从事机械动态设计及仿真研究,E-mail:dongxianrui2009@163.com.     E-mail: dongxianrui2009@163.com
作者简介: 毛君(1960-),男,满族,辽宁鞍山人,博士,教授,博士生导师,从事机械动态设计及仿真、机电一体化产品等研究,E-mail:lngcjsdxmaojun@163.com.
服务　　
把本文推荐给朋友
加入引用管理器
E-mail Alert
RSS
作者相关文章　　

引用本文:

毛君, 董先瑞, 谢苗, 闫江龙, 李翠. 智能立体停车位框架的模态分析[J]. 工程设计学报, 2016, 23(1): 54-59,81.

MAO Jun, DONG Xian-rui, XIE Miao, YAN Jiang-long, LI Cui. Modal analysis of frame on intelligent stereo parking space. Chinese Journal of Engineering Design, 2016, 23(1): 54-59,81.

链接本文:

https://www.zjujournals.com/gcsjxb/CN/10.3785/j.issn.1006-754X.2016.01.009    或    https://www.zjujournals.com/gcsjxb/CN/Y2016/V23/I1/54

[1] 杨杨.新型智能立体车库控制系统设计[D].太原:中北大学机械工程学院,2014:1-4. YANG Yang.The design of control system of intelligent stereo garage [D].Taiyuan:North University of China,College of Mechanical Engineering,2014:1-4.

[2] 刘剑,王鑫,冯海涛,等.基于三菱PLC控制塔式立体车库系统设计[J].控制工程,2009,16(S4):99-102,111. LIU Jian,WANG Xin,FENG Hai-tao,et al.Tower garage control system design based on the Mitsubishi PLC[J].Control Engineering of China,2009,16(S4):99-102,111.

[3] 毛君,谢苗,陈红月,等.框架平移回转式智能泊车装备:201110256469.8[P].2012-03-21. MAO Jun,XIE Miao,CHEN Hong-yue,et al.Intelligent parking equipment rotated and translated by frame:201110256469.8[P].2012-03-21.

[4] 毛君,谢苗,陈红月,等.载车板回转立体停车位装备:201220183739.7[P].2012-11-21. MAO Jun,XIE Miao,CHEN Hong-yue,et al.Rotating stereoscopic parking equipment worked with a plate:201220183739.7[P].2012-11-21.

[5] 毛君,谢苗,陈红月,等.单边液压驱动式立体框架停车位:201210553685.3[P].2013-04-24. MAO Jun,XIE Miao,CHEN Hong-yue,et al.Unilateral stereoscopic framework parking space driven by hydraulic power:201210553685.3[P].2013-04-24.

[6] 毛君,谢苗,陈红月,等.单边液压驱动式立体框架停车位:201220705206.0[P].2013-06-05. MAO Jun,XIE Miao,CHEN Hong-yue,et al.Unilateral stereoscopic framework parking space driven by hydraulic power:201220705206.0[P].2013-06-05.

[7] 毛君,谢苗,陈红月,等.单边电动式立体框架停车位:201220705248.4[P].2013-06-12. MAO Jun,XIE Miao,CHEN Hong-yue,et al.Unilateral stereoscopic framework parking equipment driven by electronic power:201220705248.4[P].2013-06-12.

[8] 彭斌.升降横移式立体停车库的结构设计与控制[D].兰州:兰州理工大学机械工程学院,2003:1-4. PENG Bin.Structure design and control of lifting and cross sliding type stereo parking garage[D].Lanzhou:Lanzhou University of Technology,College of Mechanical Engineering,2003:1-4.

[9] 龚海峰.升降横移式立体停车库及控制系统的研究[D].兰州:兰州理工大学石油化工学院,2003:5-28. GONG Hai-feng.Study of lifting and cross sliding type stereo parking garage and its control system[D].Lanzhou:Lanzhou University of Technology,College of Petrochemical Engineering,2003:5-28.

[10] 周智慧.立体停车库刚架结构CAE分析及其优化设计[D].苏州:苏州大学机械工程学院,2005:1-6. ZHOU Zhi-hui.The CAE analysis and optimum design of three-dimensional car parking lot rigid-framed structure[D].Suzhou:Soochow University,College of Mechanical Engineering,2005:1-6.

[11] 廖庆.垂直升降式机械立体停车系统的研究[D].武汉:武汉理工大学机械工程学院,2005:15-20. LIAO Qing.A study on vertical lifting mechanical parking system[D].Wuhan:Wuhan University of Technology,College of Mechanical Engineering,2005:15-20.

[12] 汤伟.升降横移式立体车库结构优化[D].合肥:合肥工业大学机械与汽车工程学院,2008:1-4. TANG Wei.Structural optimization of up-down and translation stereo garage and analysis of its control strategies[D].Hefei: Hefei University of Technology,School of Mechanical and Automotive Engineering,2008:1-4.

[13] 杨承超.基于立体停车的隔层桁架式抗侧力钢构架的性能研究[D].长沙:湖南大学土木工程学院,2011:1-5. YANG Cheng-chao.The research on performance of interlayer truss lateral resisting steel skeleton based on three-dimensional parking[D].Changsha:Hunan University,Civil Engineering College,2011:1-5.

[14] 刘爽.PJSC型立体停车设备研究[D].阜新:辽宁工程技术大学机械工程学院,2012:7-21. LIU Shuang.Study on PJSC type stereo parking equinpment[D].Fuxin:Liaoning Technical University,College of Mechanical Engineering,2012:7-21.

[15] 毛君,佟阳,谢苗,等.智能立体车位防坠落系统动力学特性仿真[J].计算机系统应用,2012,21(11):80-83. MAO Jun,TONG Yang,XIE Miao,et al.Dynamic characteristics simulation of intelligent three-dimensional parking spaces falling protection system[J]. Computer Systems & Applications,2012,21(11):80-83.

[16] 毛君,路朝留,谢苗,等.立体车位提升系统动力学仿真及分析[J].现代制造工程,2013(10):64-66,133. MAO Jun,LU Chao-liu,XIE Miao,et al.Stereo parking lifting system dynamics simulation and analysis[J].Modern Manufacturing Engineering,2013(10):64-66,133.

[17] 刘小华.带环箍层钢框架立体停车结构静力及动力性能研究[D].长沙:湖南大学土木工程学院,2013:1-9. LIU Xiao-hua.Research on static and dynamic performance of steel-framed tridimensional parking structures with hoop-storeys[D].Changsha:Hunan University,Civil Engineering College,2013:1-9.

[18] 陈婷婷.机械式立体停车库的设计研究[D].兰州:兰州大学土木工程与力学学院,2013:1-11. CHEN Ting-ting.The study of design for mechanical stereo garage[D].Lanzhou:Lanzhou University,College of Civil Engineering and Mechanics,2013:1-11.

[19] 卢进南,毛君,谢苗,等.巷道超前支架全支撑态动力学模型[J].煤炭学报,2015,40(1):50-57. LU Jin-nan,MAO Jun,XIE Miao,et al.Dynamics model of advanced powered support in heading under full support situation[J].Journal of China Coal Society,2015,40(1):50-57.

[20] 于天彪,王学智,关鹏,等.超高速磨削机床主轴系统模态分析[J].机械工程学报,2012,48(17):183-188. YU Tian-biao,WANG Xue-zhi,GUAN Peng,et al.Modal analysis of spindle system on ultra-high speed grinder[J].Chinese Journal of Mechanical Engineering,2012,48(17):183-188.

[21] 张春林.高等机构学[M].北京:北京理工大学出版社,2005:36-63. ZHANG Chun-lin.Advanced mechanism[M].Beijing:Beijing University of Technology Press,2005:36-63.

[22] 陈艳霞,陈磊.ANSYS Workbench工程应用案例精通[M].北京:电子工业出版社,2012:30-89. CHEN Yan-xia,CHEN Lei.Proficient in ANSYS Workbench engineering application cases [M].Beijing:Publishing House of Electronics Industry,2012:30-89.
[1] 谢苗, 张保国, 王鹏飞, 李政. 基于相似理论的掘进机主动激振截割性能研究[J]. 工程设计学报, 2021, 28(5): 576-584.
[2] 曹恩国, 王刚, 王琨, 高阳. 基于弹性装置驱动的外骨骼助行效能评价[J]. 工程设计学报, 2021, 28(4): 480-488.
[3] 刘晓瑜, 田颖, 张明路. 水下机械手动力学研究综述[J]. 工程设计学报, 2021, 28(4): 389-398.
[4] 李响, 王阳, 童冠, 陈波文, 何彬. 四边简支新型类方形蜂窝夹层结构振动特性研究[J]. 工程设计学报, 2018, 25(6): 725-734.
[5] 魏春雨, 蔡月, 刘明贺, 张琦, 贾乾忠. 新型车载医疗救护隔振平台设计及仿真[J]. 工程设计学报, 2018, 25(5): 532-538.
[6] 黄志强, 李刚, 陶知非, 郝磊. 可控震源振动器有限元模态分析与试验验证[J]. 工程设计学报, 2017, 24(5): 530-535.
[7] 谢苗, 闫江龙, 毛君, 李翠, 刘一柱. 智能立体停车位液压控制系统分析[J]. 工程设计学报, 2017, 24(3): 337-342.
[8] 谢苗, 刘治翔, 毛君. 立体停车位液压系统控制策略及节能控制技术研究[J]. 工程设计学报, 2017, 24(1): 115-120.
[9] 王杰, 钱利勤, 陈新龙, 孙巧雷, 邓自强, 冯定. 自动猫道起升系统动力学模型与分析[J]. 工程设计学报, 2016, 23(5): 437-443,460.
[10] 陈健伟, 朱大昌, 张荣兴, 朱城伟. 3-RPRR类平面全柔性并联机构拓扑优化设计[J]. 工程设计学报, 2016, 23(3): 251-255,270.
[11] 谢 苗，白雅静，毛 君，董先瑞，卢进南. 不同工况下超前支护装备的模态分析[J]. 工程设计学报, 2015, 22(3): 236-242.
[12] 黄尚兵, 金光, 安源. 凸轮机构两质量动力学模型的运动误差及接触力分析[J]. 工程设计学报, 2013, 20(3): 250-253.
[13] 冉光斌, 余绍蓉, 刘小刚, 洪建忠, 胡杰. 土工二维振动离心机转臂的设计研究[J]. 工程设计学报, 2013, 20(1): 70-74.
[14] 张青雷,沈海鸥,王少波,陈冰. 高速动平衡机摆架振动特性分析与改进[J]. 工程设计学报, 2012, 19(2): 91-95.
[15] 郭宁平, 周海波, 王文祝, 郑 蕾. 磁悬浮直线运动平台的模态分析[J]. 工程设计学报, 2011, 18(3): 183-190.