Please wait a minute...
工程设计学报  2016, Vol. 23 Issue (1): 49-53,73    DOI: 10.3785/j.issn.1006-754X.2016.01.008
建模、分析、优化和决策     
精密离心机热变形多物理场耦合数值计算
卢燕1, 王珏2, 凌明祥2, 杜平安1
1. 电子科技大学 机械电子工程学院, 四川 成都 611731;
2. 中国工程物理研究院 总体工程研究所, 四川 绵阳 621900
Numerical simulation of multi-physics coupling for the thermal deformation of precision centrifuge
LU Yan1, WANG Jue2, LING Ming-xiang2, DU Ping-an1
1. School of Mechatronics Engineering, University of Electronic Science and Technology of China, Chengdu 611731, China;
2. Institute of Systems Engineering, China Academy of Engineering Physics, Mianyang 621900, China
 全文: PDF(1802 KB)   HTML
摘要: 离心机是惯性导航系统加速度计的标定设备,转盘变形将严重影响标定精度.综合考虑离心机机室内空气流动、流动传热以及机箱和转盘的导热,结合CFD和FEM方法,对精密离心机的热变形进行流-热-固多场耦合计算.分析了多物理场耦合计算原理,采用流固耦合换热整场求解法计算离心机温度场,采用顺序耦合法计算转盘热变形.计算结果表明:在300 r/min转速下,转盘最大温升为1.23 ℃;越远离转盘中心,温升越大;加速度计安装位置的温度计算值与实测值一致,验证了本方法的正确性;转盘安装加速度计位置的径向热变形为7.89 μm,热变形是变形累积的结果且随着转盘转速增加而增大.
关键词: 精密离心机多物理场耦合流固耦合换热温度场热变形    
Abstract: Centrifuge is a calibrating device of accelerometer in inertial navigation system,and deformation of the rotator could seriously affect the calibrating accuracy.The centrifuge indoor air flow,heat transfer and heat conduction of cabinet and rotator were considered when the thermal deformation was analyzed through a multi-field coupling simulation,which combined the methods of CFD and FEM.The multi-physics coupling calculation principles were analyzed.Temperature field was calculated by using conjugate heat transfer method,and thermal deformation was obtained by the sequential coupling method.The results showed that at speed of 300 r/min,the maximum temperature rise was 1.23 ℃,and the farther away from the rotator center,the bigger temperature rise.The calculated temperature at the location for mounting accelerometer was consistent with the measured value.The radial deformation of the accelerometer location was 7.89 μm.Thermal deformation is a result of accumulated deformation,and increases with the rotating speed.
Key words: precision centrifuge    multi-physics coupling    fluid solid conjugate heat transfer    temperature field    thermal deformation
收稿日期: 2015-06-30 出版日期: 2016-02-28
CLC:  TH89  
基金资助:

国家重大科学仪器设备开发专项(2011YQ130047).

通讯作者: 王珏(1982-),男,四川绵阳人,工程师,硕士,从事多学科建模与仿真技术研究,E-mail:witchover@163.com.     E-mail: witchover@163.com
作者简介: 卢燕(1990-),女,贵州福泉人,硕士生,从事流-热-固多物理场耦合数值计算研究,E-mail:luyan2161@163.com.
服务  
把本文推荐给朋友
加入引用管理器
E-mail Alert
RSS
作者相关文章  

引用本文:

卢燕, 王珏, 凌明祥, 杜平安. 精密离心机热变形多物理场耦合数值计算[J]. 工程设计学报, 2016, 23(1): 49-53,73.

LU Yan, WANG Jue, LING Ming-xiang, DU Ping-an. Numerical simulation of multi-physics coupling for the thermal deformation of precision centrifuge. Chinese Journal of Engineering Design, 2016, 23(1): 49-53,73.

链接本文:

https://www.zjujournals.com/gcsjxb/CN/10.3785/j.issn.1006-754X.2016.01.008        https://www.zjujournals.com/gcsjxb/CN/Y2016/V23/I1/49

[1] YAZDI N,AYAZI F,NAJAFI K.Micro-machined inertial sensors[J].Proceedings of the IEEE,1998,86(8):1640-1655.

[2] 何铁春,周世勤.惯性导航加速度计[M].北京:国防工业出版社,1983:352-353. HE Tie-chun,ZHOU Shi-qin.Inertial navigation accelerometer [M].Beijing:National Defence Industry Press,1983:352-353.

[3] YANG Y,HUO X.Measuring and balancing dynamic unbalance of precision centrifuge[J].International Symposium on Instrumentation Science and Technology,2008:11-16.

[4] 尹小恰.精密离心机工作半径的测试方法与误差分析[D].哈尔滨:哈尔滨工业大学航天学院,2013:2-12. YIN Xiao-qia.The measurement method and error analysis for the working radius of precision centrifuge[D].Harbin:Harbin Institute of Technology,School of Astronautics,2013:2-12.

[5] 宋少云.多场耦合问题的协同求解方法研究与应用[D].武汉:华中科技大学机械科学与工程学院,2007:2-3. SONG Shao-yun.Research and application of collaborative solution method for multiphysics problems[D].Wuhan:Huazhonhg University of Science and Technology,School of Mechanical Science and Engineering,2007:2-3.

[6] FELIPPA C A,PARK K C,FARHAT C.Partitioned analysis of coupled mechanical systems[J].Computer Methods in Applied Mechanics and Engineering,2001,190(24/25):3247-3270.

[7] 黄唐,毛国良,姜贵庆,等.二维流场、热、结构一体化数值模拟[J].空气动力学报,2000,18(1):115-119. HUANG Tang,MAO Guo-liang,JIANG Gui-qing,et al.Two dimensional coupled flow-thermal-structural numerical simulation[J].Acta Aerodynamica Sinica,2000,18(1):115-119.

[8] 钱若军.流固耦合理论研究进展[J].空间结构,2008,14(1):3-14. QIAN Ruo-jun.Advances in research on fluid-structure interaction theory[J].Spatial Structures,2008,14(1):3-14.

[9] MALATIP A,WANSOPHARK N,DECHAUMPHAI P.Fractional four-step finite element method for analysis of thermally coupled fluid-solid interaction problems[J].Applied Mathematics and Mechanics,2012,33(1):99-116.

[10] 徐太栋.精密离心机空气流场的数值模拟[D].成都:电子科技大学机械电子工程学院,2014:22-30. XU Tai-dong.Numerical simulation of airflow field for the precision centrifuge[D].Chengdu:University of Electronic Science and Technology of China,School of Mechatronics Engineering,2014:22-30.
[1] 唐绍禹,吴杰,张辉,邓兵兵,黄禹铭,黄浩. 多极式磁流变离合器温度场仿真与实验研究[J]. 工程设计学报, 2022, 29(4): 484-492.
[2] 武聪魁, 何柏岩, 袁鹏飞. 计及金属铰链的环形可展天线热-结构分析[J]. 工程设计学报, 2020, 27(3): 349-356.
[3] 高卫国, 王伟松, 张大卫, 刘腾, 李金和, 翁凌韬, 齐向阳. 考虑结构热变形的机床进给系统热误差研究[J]. 工程设计学报, 2019, 26(1): 29-38.
[4] 聂明争, 范勤, 王雄, 李知存. FDM技术中加热底板样式对翘曲变形的影响研究[J]. 工程设计学报, 2018, 25(4): 420-425,440.
[5] 胡俊峰,郝亚洲,徐贵阳,杨 健. 考虑温度效应的微操作平台的建模与性能分析[J]. 工程设计学报, 2015, 22(2): 143-154.
[6] 徐太栋,杜平安,王 炼,黄 鹏,冯加权,张映梅. 基于CFD的精密离心机风阻优化[J]. 工程设计学报, 2014, 21(6): 572-577.
[7] 赵丽娟,李明昊. 基于多场耦合的采煤机摇臂壳体分析[J]. 工程设计学报, 2014, 21(3): 235-239.
[8] 陈志华, 关富玲. 星载抛物面天线热变形敏感性分析[J]. 工程设计学报, 2010, 17(4): 263-267.
[9] 苏荣华, 刘伟军, 龙日升. 不同基板预热温度对激光金属沉积成形过程温度场的影响[J]. 工程设计学报, 2009, 16(1): 44-49.
[10] 李金国,刘 红. 橡胶注射机模具加热系统温度场模拟仿真[J]. 工程设计学报, 2008, 15(4): 300-302.
[11] 林谢昭, 高诚辉, 黄健萌. 制动工况参数对制动盘摩擦温度场分布的影响[J]. 工程设计学报, 2006, 13(1): 45-48.