机械工程 |
|
|
|
|
新型气动比例压力阀的建模研究与特性分析 |
班伟1 , 陶国良1 , 路波2,孟德远1 , 袁月峰3 |
1.浙江大学 流体传动及控制国家重点实验室, 浙江 杭州 310027; 2.国家气动产品质量监督检验中心, 浙江 宁波 315500;
3.中国计量学院 质量与安全工程学院, 浙江 杭州 310018 |
|
Modeling and characteristics investigation on a new pneumatic
proportional pressure valve |
BAN Wei1, TAO Guo-liang1, LU Bo2, MENG De-yuan1, YUAN Yue-feng3 |
1. State Key Laboratory of Fluid Power Transmission and Control,Zhejiang University,Hangzhou 310027,China;
2. National Quality Supervision and Inspection Center of Pneumatic Products, Ningbo 315500, China;
3. College of Quality & Safety Engineering, China Jiliang University, Hangzhou 310018, China |
引用本文:
班伟 , 陶国良 , 路波,孟德远 , 袁月峰. 新型气动比例压力阀的建模研究与特性分析[J]. J4, 2012, 46(11): 1953-1959.
BAN Wei, TAO Guo-liang, LU Bo, MENG De-yuan, YUAN Yue-feng. Modeling and characteristics investigation on a new pneumatic
proportional pressure valve. J4, 2012, 46(11): 1953-1959.
链接本文:
http://www.zjujournals.com/eng/CN/10.3785/j.issn.1008-973X.2012.11.003
或
http://www.zjujournals.com/eng/CN/Y2012/V46/I11/1953
|
[1] ARAKI K, CHEN N. Pressure versus characteristics of a diaphragm type pneumatic pressure control proportional valve [C]∥ Proceedings of the 4th JHPS Int. Symp. Tokyo, Japan:\ [s.n.\], 1999, 413-418.
[2] MIYAJIMA T, FUJIATA T, SAKAKI K, et al. Development of a digital control system for highperformance pneumatic servo valve [J]. Precision Engineering, 2007, 31(2):156-161.
[3] CHO S H, FIEDLER M, RUDIGER F, et al. Virtualdesignmodelbased pressuretracking control of high dynamic pneumatic valves using a sliding mode controller combined with a proportionalintegralderivation scheme [J]. Proceedings of the Institution of Mechanical Engineers, Part I: Journal of Systems and Control Engineering, 2006, 220(5):353-364.
[4] WANG Xuesong, CHENG Yuhu, PENG Guangzheng. Modeling and selftuning pressure regulator design for pneumatic pressure load systems [J]. Control Engineering Practice, 2007, 15(9):1161-1168.
[5] CHEN Yize, WANG Xuanyin, XU Zhipeng, et al. Pilot leakages influences on the performances of extra high pressure proportional pneumatic valve [J]. Chinese Journal of Mechanical Engineering, 2005, 18(2):208-211.
[6] 路波,陶国良,袁月峰,等. 高精度气动比例压力阀的设计及特性研究[J]. 农业机械学报, 2009, 40(10):181-187.
LU Bo, TAO Guoliang, YUAN Yuefeng, et al. Design and characteristics investigation of a high precision pneumatic proportional pressure valve [J]. Transactions of the Chinese Society for Agricultural Machinery, 2009, 40(10):181-187.
[7] SORLI M, FIGLIOLINI G, ALMONDO A. Mechatronic model and experimental validation of a pneumatic servosolenoid valve [J]. Journal of Dynamic Systems, Measurement, and Control, 2010, 132(5):054503.1-054503.10.
[8] GADYUCHKO A, BUSSINGER F, KALLENBACH E. Control concept for hysteresis free behavior of proportional solenoid [C]∥ 7th International Fluid Power Conference. Aachen: [s. n.], 2010, 1-14.
[9] XIANG Zhong, LIU Hao, TAO Guoliang, et al. Development of an εtype actuator for enhancing highspeed electropneumatic ejector valve performance [J]. Journal of Zhejiang University Science A, 2008, 9(11):1552-1559.
[10]SORLI M, FIGLIOLINI G, PASTORELLI S. Dynamic model and experimental investigation of a pneumatic proportional pressure valve [J]. IEEE/Asme Transactions on Mechatronics, 2004, 9(1):78-86.
[11] NABI A, WACHOLDER E, DAYAN J. Dynamic model for a domeLoaded pressure regulator [J]. Journal of Dynamic Systems, Measurement, and Control, 2000, 122(2):290-297.
[12] KUKULKA D J, BENZONI A, MOLLENDORF J C. Digital simulation of a pneumatic pressure regulator [J]. Simulation, 1994, 63(4):252-266.
[13] MATLAB. Variable area pneumatic orifice [EB/OL].[2010/03/12]. http://www.mathworks.com/help/toolbox/physmod/simscsim/ref/variableareapneumaticorifice.html.
[14] BEATER P. Pneumatic Driver: system design, modeling and control [M]. New York: Springer, 2007,41-48. |
|
Viewed |
|
|
|
Full text
|
|
|
|
|
Abstract
|
|
|
|
|
Cited |
|
|
|
|
|
Shared |
|
|
|
|
|
Discussed |
|
|
|
|