Please wait a minute...
浙江大学学报(工学版)
J4  2012, Vol. 46 Issue (11): 1953-1959    DOI: 10.3785/j.issn.1008-973X.2012.11.003
机械工程     
新型气动比例压力阀的建模研究与特性分析
班伟1 , 陶国良1 , 路波2,孟德远1 , 袁月峰3
1.浙江大学 流体传动及控制国家重点实验室, 浙江 杭州 310027; 2.国家气动产品质量监督检验中心, 浙江 宁波 315500;
3.中国计量学院 质量与安全工程学院, 浙江 杭州 310018
Modeling and characteristics investigation on a new pneumatic
proportional pressure valve
BAN Wei1, TAO Guo-liang1, LU Bo2, MENG De-yuan1, YUAN Yue-feng3
1. State Key Laboratory of Fluid Power Transmission and Control,Zhejiang University,Hangzhou 310027,China;
2. National Quality Supervision and Inspection Center of Pneumatic Products, Ningbo 315500, China;
3. College of Quality & Safety Engineering, China Jiliang University, Hangzhou 310018, China
 全文: PDF  HTML
摘要：

为满足电-气比例/伺服系统的应用需要,设计一种由比例电磁铁、活塞式阀芯及两位三通的阀体构成的直动式气动比例压力阀,并建立该比例阀的非线性数学模型.对于比例电磁铁,采用集总参数模型来描述电磁特性,模型参数由FEM分析得到.结合机械及气路的物理特性,分别对上、下阀芯的运动特性、阀体内的气体流动及热力学过程进行建模分析,保证了上、下阀芯的运动独立性.通过仿真对下阀芯的黏性摩擦系数、反馈通道的直径以及气源压力等影响比例压力阀的压力响应特性的因素进行分析,并设计一种比例压力阀的性能测试系统以验证模型的正确性.仿真与实验结果呈现良好的一致性,模型能够预测不同阶跃输入信号下该比例阀的压力响应过程.
Abstract:

A direct drive type three-port pneumatic pressure valve, consisting of a proportional solenoid and a poppet assembly, was developed to fulfill the application requirement of electro-pneumatic servo system. A nonlinear lumped parameter model of the proportional solenoid, whose parameters were obtained by FEM analysis, was created to describe the complex magnetic characteristics. The movements of poppet assembly, pneumatic and thermodynamic properties in the valve were analyzed by taking account of physical effects of mechanical and pneumatic subsystem separately, and independence of the movements between poppet assemblies is allowed. The influence of poppet viscous friction coefficient, feedback pass diameter and air supply pressure was studied. A special test system was designed to verify the proposed model. Good comparison results between experiment and simulation are obtained, and the model can be used to predict valve's transient pressure response under different step input signals．
出版日期: 2012-12-11
:  TH 138.523  
基金资助:

浙江省宁波市自然科学基金资助项目(2010A610130) .
通讯作者: 陶国良,男,教授,博导.     E-mail: gltao@zju.edu.cn
作者简介: 班伟(1984-), 男, 博士, 主要从事气动电子技术研究. E-mail: realbw@zju.edu.cn．
服务　　
把本文推荐给朋友
加入引用管理器
E-mail Alert
RSS
作者相关文章　　

引用本文:

班伟 , 陶国良 , 路波,孟德远 , 袁月峰. 新型气动比例压力阀的建模研究与特性分析[J]. J4, 2012, 46(11): 1953-1959.

BAN Wei, TAO Guo-liang, LU Bo, MENG De-yuan, YUAN Yue-feng. Modeling and characteristics investigation on a new pneumatic
proportional pressure valve. J4, 2012, 46(11): 1953-1959.

链接本文:

http://www.zjujournals.com/eng/CN/10.3785/j.issn.1008-973X.2012.11.003    或    http://www.zjujournals.com/eng/CN/Y2012/V46/I11/1953

［1］ ARAKI K, CHEN N. Pressure versus characteristics of a diaphragm type pneumatic pressure control proportional valve ［C］∥ Proceedings of the 4th JHPS Int. Symp. Tokyo, Japan:\
[s.n.\], 1999, 413-418．
［2］ MIYAJIMA T, FUJIATA T, SAKAKI K, et al. Development of a digital control system for highperformance pneumatic servo valve ［J］. Precision Engineering, 2007, 31(2):156-161．
［3］ CHO S H, FIEDLER M, RUDIGER F, et al. Virtualdesignmodelbased pressuretracking control of high dynamic pneumatic valves using a sliding mode controller combined with a proportionalintegralderivation scheme ［J］. Proceedings of the Institution of Mechanical Engineers, Part I: Journal of Systems and Control Engineering, 2006, 220(5):353-364．
［4］ WANG Xuesong, CHENG Yuhu, PENG Guangzheng. Modeling and selftuning pressure regulator design for pneumatic pressure load systems ［J］. Control Engineering Practice, 2007, 15(9):1161-1168．
［5］ CHEN Yize, WANG Xuanyin, XU Zhipeng, et al. Pilot leakages influences on the performances of extra high pressure proportional pneumatic valve ［J］. Chinese Journal of Mechanical Engineering, 2005, 18(2):208-211．
［6］ 路波,陶国良,袁月峰,等. 高精度气动比例压力阀的设计及特性研究［J］. 农业机械学报, 2009, 40(10):181-187．
LU Bo, TAO Guoliang, YUAN Yuefeng, et al. Design and characteristics investigation of a high precision pneumatic proportional pressure valve ［J］. Transactions of the Chinese Society for Agricultural Machinery, 2009, 40(10):181-187．
［7］ SORLI M, FIGLIOLINI G, ALMONDO A. Mechatronic model and experimental validation of a pneumatic servosolenoid valve ［J］. Journal of Dynamic Systems, Measurement, and Control, 2010, 132(5):054503.1-054503.10．
［8］ GADYUCHKO A, BUSSINGER F, KALLENBACH E. Control concept for hysteresis free behavior of proportional solenoid ［C］∥ 7th International Fluid Power Conference. Aachen: ［s. n.］, 2010, 1-14．
［9］ XIANG Zhong, LIU Hao, TAO Guoliang, et al. Development of an εtype actuator for enhancing highspeed electropneumatic ejector valve performance ［J］. Journal of Zhejiang University Science A, 2008, 9(11):1552-1559．
［10］SORLI M, FIGLIOLINI G, PASTORELLI S. Dynamic model and experimental investigation of a pneumatic proportional pressure valve ［J］. IEEE/Asme Transactions on Mechatronics, 2004, 9(1):78-86．
［11］ NABI A, WACHOLDER E, DAYAN J. Dynamic model for a domeLoaded pressure regulator ［J］. Journal of Dynamic Systems, Measurement, and Control, 2000, 122(2):290-297．
［12］ KUKULKA D J, BENZONI A, MOLLENDORF J C. Digital simulation of a pneumatic pressure regulator ［J］. Simulation, 1994, 63(4):252-266．
［13］ MATLAB. Variable area pneumatic orifice ［EB/OL］.［2010/03/12］. http://www.mathworks.com/help/toolbox/physmod/simscsim/ref/variableareapneumaticorifice.html．
［14］ BEATER P. Pneumatic Driver: system design, modeling and control ［M］. New York: Springer, 2007,41-48．
[1] 刘琼,陶国良,钟伟,班伟. 内外爆气动开关阀[J]. J4, 2013, 47(5): 790-795.