Please wait a minute...
Chinese Journal of Engineering Design  2014, Vol. 21 Issue (2): 172-179    DOI: 10.3785/j.issn. 1006-754X.2014.02.012
    
Study on RC beams shear behavior strengthened with HPFL
ZENG Ling-hong, JIN Dong-liang
College of Civil Engineering, Hunan University, Changsha 410082, China
Download: HTML     PDF(2053KB)
Export: BibTeX | EndNote (RIS)      

Abstract  Combined with an engineering example and experiment data, theoretical formula of the reinforced concrete (RC) beams shear capacity with highperformance ferrocement laminate (HPFL) after fire was deduced and verified. Considering the impacts on the strength of concrete and steel, the calculation model was put forward on the basis of domestic and international scholars research on the changes of concretes and steels strength after fire. It was assumed that there was no relative slipping between steel and concrete and the tensile strength of concrete was ignored. Combined with the limit equilibrium principle, the softening of concrete compressive strength under the condition of the tensile strain was considered. Regardless of the coupling action of temperaturestress, the equivalent section method was adopted on the basis of trussarch model. The results show that this method of reinforcement significantly improves the shear capacity of the reinforced beam. The calculation results are in good agreement with the experimental ones. The results can be referenced for beams strengthened with highperformance ferrocement.

Key wordshighperformance ferrocement laminate      fire      shear      strengthening     
Published: 28 April 2014
Cite this article:

ZENG Ling-hong, JIN Dong-liang. Study on RC beams shear behavior strengthened with HPFL. Chinese Journal of Engineering Design, 2014, 21(2): 172-179.

URL:

https://www.zjujournals.com/gcsjxb/10.3785/j.issn. 1006-754X.2014.02.012     OR     https://www.zjujournals.com/gcsjxb/Y2014/V21/I2/172


HPFL加固受火RC梁抗剪性能研究

对高性能复合砂浆钢筋混凝土加固受火RC梁的抗剪承载力进行理论推导,并结合实验数据和工程实例验证理论公式的合理性.结合国内外对火灾后钢筋混凝土结构中混凝土和钢筋强度变化的研究,考虑火灾和火灾后冷却条件对混凝土和钢筋强度及性能的影响,提出计算模型.假定钢筋和混凝土之间无相对滑移,忽略混凝土的抗拉强度,不考虑温度—应力的耦合作用,采用等效截面法得到等效截面为T形截面,以桁架拱模型和软化桁架理论为基础,结合极限平衡原理,考虑拉应变存在条件下混凝土抗压强度的软化.分析结果表明,推导所得的计算公式与试验数据比较吻合,高性能复合砂浆钢筋网加固方法能使梁的抗剪承载力得到显著提高,能满足实际工程的应用.

关键词: 高性能复合砂浆钢筋网,  火灾,  抗剪,  加固 
[1] LI Yang, NIE Yu-fei. Design and analysis of heat insulation sealing door of sodium combustion test plant[J]. Chinese Journal of Engineering Design, 2022, 29(1): 115-122.
[2] BAI Yang-xi, CHEN Hong-yue, CHEN Hong-yan, WANG Xin, LI Jian-gang. Vibration analysis and experimental verification of shearer sliding shoes based on drum load[J]. Chinese Journal of Engineering Design, 2021, 28(3): 358-366.
[3] Lü Jun, LIU Guo-hua, WANG Yu. Research on structural safety degree of old stone masonry arch dam[J]. Chinese Journal of Engineering Design, 2021, 28(1): 56-62.
[4] BAI Yang-xi, CHEN Hong-yue, CHEN Hong-yan, WANG Xin. Analysis and test verification of transverse vibration of shearer rocker arm under multiple constraints[J]. Chinese Journal of Engineering Design, 2020, 27(6): 707-712.
[5] KONG Chui-wang, CHEN Wei-lin, LU Qing-hua, LUO Lu-feng, ZHANG Yun-zhi. Nonlinear modeling and optimization of single-stage compliant orthogonal displacement amplification mechanism[J]. Chinese Journal of Engineering Design, 2020, 27(1): 76-86.
[6] QIAO Chun-guang, WANG Xue-wen, XIE Jia-cheng, YANG Zhao-jian. Vertical plane shape calculation method of scraper conveyor based on running track of shearer[J]. Chinese Journal of Engineering Design, 2018, 25(5): 495-502.
[7] CHEN Hong-yue, LI Yong-hong, DENG Wen-hao, YUAN Zhi, LI En-dong. Tension analysis of the drum shearer hydraulic pull rod[J]. Chinese Journal of Engineering Design, 2018, 25(1): 118-122.
[8] ZHANG Qiang, WU Ze-guang, CHU Viet Dung, WU Ze-yang, LI Li-ying. Research on mechanical detecting system of hydraulic rod on shearer[J]. Chinese Journal of Engineering Design, 2017, 24(5): 595-600.
[9] ZHANG Qiang, WANG Hai-jian, WU Ze-guang, LIU Zhi-heng, MAO Jun. Research of coal-rock cutting mechanical characteristic and test system for drum shearer[J]. Chinese Journal of Engineering Design, 2017, 24(4): 459-464,479.
[10] JIANG Li-chun, WANG Guo-wei, WU Ai-xiang. Research on the method of similar layer shearing model for dynamic respones of goaf group[J]. Chinese Journal of Engineering Design, 2017, 24(3): 256-263.
[11] CHEN Xue-jun, YANG Yong-ming. Jet trajectory model and positioning compensation method for fire water cannon[J]. Chinese Journal of Engineering Design, 2016, 23(6): 558-563,611.
[12] LI Qiang, MAO Jun, ZHANG Ming-yu, XIE Miao. Three-axis force testing scheme design and experimental study of shearer cutter[J]. Chinese Journal of Engineering Design, 2016, 23(5): 506-512.
[13] CHEN Hong-yue, LIU Lie-bei, MAO Jun, SONG Qiu-shuang, YUAN Zhi. The analysis of the shearer dynamic feature in the coupling relation between the the motivation and the drum vibration[J]. Chinese Journal of Engineering Design, 2016, 23(3): 228-234.
[14] MAO Jun, PAN De-wen, LI Qiang, XIE Miao, YOU Xu-ping. Analysis of mechanical properties of shearer drum in the process of oblique feed[J]. Chinese Journal of Engineering Design, 2015, 22(6): 613-618.
[15] LIU Chun-sheng, TIAN Cao. The mechanical properties and design of shearer hydraulic adjustable posture traction mechanism[J]. Chinese Journal of Engineering Design, 2015, 22(3): 243-249.