Please wait a minute...
工程设计学报  2004, Vol. 11 Issue (3): 119-122    
工程设计理论、方法与技术     
微小卫星特征结构模块的振动模态测试与计算补偿
 曾攀, 杨濯, 雷丽萍, 李路明
清华大学 机械工程系,北京 100084
Vibration test and compensation computing for structural
pattern of small satellite
 ZENG  Pan, YANG  Zhuo, LEI  Li-Ping, LI  Lu-Ming
Department of Mechanical Engineering, Qinghua University, Beijing 100084, China
 全文: PDF(411 KB)   HTML
摘要: 对微小卫星的特征结构模块的振动力学特性进行试验测试,同时对该结构模块的设计进行计算建模,分别给出了基于C1型壳梁单元的简化模型和精细模型,并将计算模型用于试验测试数据的计算补偿,以消除测试过程中由传感器的附加质量给结构系统带来的附加影响,最后获得结构系统的真实模态信息,为微小卫星框架的优化设计提供重要参考。
关键词: 小卫星框架 模态分析有限元建模 计算补偿    
Abstract: The vibration performance of structural pattern of the small satellite is tested. The numerical models are built using the C1-type shell-beam element. Since there exists an obvious influence of additional mass of sensor during testing, the numerical analysis could be used to get the true results after compensation treating, which can get rid of the additional influence of sensor. A set of results both in test and computing are presented to demonstrate the whole treating process.
Key words: small satellite    modal analysis    FEM modeling    compensation
出版日期: 2004-06-28
基金资助:

国家自然科学基金资助项目(50175060)

服务  
把本文推荐给朋友
加入引用管理器
E-mail Alert
RSS
作者相关文章  
曾攀
杨濯
雷丽萍
李路明

引用本文:

曾攀, 杨濯, 雷丽萍, 李路明. 微小卫星特征结构模块的振动模态测试与计算补偿[J]. 工程设计学报, 2004, 11(3): 119-122.

ZENG Pan, YANG Zhuo, LEI Li-Ping, LI Lu-Ming. Vibration test and compensation computing for structural
pattern of small satellite[J]. Chinese Journal of Engineering Design, 2004, 11(3): 119-122.

链接本文:

https://www.zjujournals.com/gcsjxb/CN/        https://www.zjujournals.com/gcsjxb/CN/Y2004/V11/I3/119

[1] 谢苗, 张保国, 王鹏飞, 李政. 基于相似理论的掘进机主动激振截割性能研究[J]. 工程设计学报, 2021, 28(5): 576-584.
[2] 李响, 王阳, 童冠, 陈波文, 何彬. 四边简支新型类方形蜂窝夹层结构振动特性研究[J]. 工程设计学报, 2018, 25(6): 725-734.
[3] 黄志强, 李刚, 陶知非, 郝磊. 可控震源振动器有限元模态分析与试验验证[J]. 工程设计学报, 2017, 24(5): 530-535.
[4] 陈健伟, 朱大昌, 张荣兴, 朱城伟. 3-RPRR类平面全柔性并联机构拓扑优化设计[J]. 工程设计学报, 2016, 23(3): 251-255,270.
[5] 毛君, 董先瑞, 谢苗, 闫江龙, 李翠. 智能立体停车位框架的模态分析[J]. 工程设计学报, 2016, 23(1): 54-59,81.
[6] 谢 苗,白雅静,毛 君,董先瑞,卢进南. 不同工况下超前支护装备的模态分析[J]. 工程设计学报, 2015, 22(3): 236-242.
[7] 张青雷,沈海鸥,王少波,陈冰. 高速动平衡机摆架振动特性分析与改进[J]. 工程设计学报, 2012, 19(2): 91-95.
[8] 郭宁平, 周海波, 王文祝, 郑 蕾. 磁悬浮直线运动平台的模态分析[J]. 工程设计学报, 2011, 18(3): 183-190.
[9] 谭启檐, 高云国, 王小庆, 薛向尧. 激光转台芯部结构动态特性研究与优化[J]. 工程设计学报, 2010, 17(3): 186-189.
[10] 张磊磊, 张秋菊. 纱线张力传感器弹性体有限元分析及优化设计[J]. 工程设计学报, 2007, 14(5): 392-394.
[11] 应富强, 李敏, 吕原君. 车用电涡流缓速器试验台组合飞轮系设计及优化[J]. 工程设计学报, 2006, 13(4): 249-254.
[12] 沈润杰, 何闻. 离心机动力学特性分析及设计技术[J]. 工程设计学报, 2006, 13(3): 150-153.
[13] 李小雷, 童水光. 高速切削刀具系统固有特性和动态响应分析[J]. 工程设计学报, 2004, 11(5): 268-272.