Please wait a minute...
工程设计学报  2011, Vol. 18 Issue (4): 265-269    
工程设计理论、方法与技术     
基于CFD的车辆进气系统流场仿真与分析
 王治林1, 成 凯1, 林 源2
1.吉林大学 机械科学与工程学院,吉林 长春 130025; 2.长春职业技术学院,吉林 长春130025
Fluid simulation and analysis for automotive air intake systems based on CFD
 WANG  Zhi-Lin1, CHENG  Kai1, LIN  Yuan2
1. College of Mechanical Science and Engineering, Jilin University, Changchun 130025, China;
2. Changchun Vocational Institute of Technology, Changchun 130025, China
 全文: PDF(2148 KB)   HTML
摘要: 针对传统发动机辅助系统中进气系统的设计多采用经验公式,结果不够准确这一问题,提出了基于计算流体动力学(computational fluid dynamics,CFD)的设计方法.通过建立进气系统的三维模型并进行网格划分,选择RNG(renormalization-group)湍流模型建立气相的数学模型,定义适当的边界条件,利用Fluent软件对进气系统气相流动规律进行数值模拟.在充分考虑空气滤清器滤网的影响,将滤网结构设为多孔介质区域的基础上,对比分析3种设计方案内部流场的速度矢量分布和压力分布,以进气阻力为评判准则,确定进气阻力最小的方案2为最佳设计方案.这种方法对进气系统的设计提供了实用的参考.
关键词: 进气系统CFD多孔介质优化设计    
Abstract: Generally, the empirical equations are frequently used in the traditional design method of air intake system of engine auxiliary system, which leads to the results inaccuracy, sometimes big deviation exists between the empirical data and calculated data. Aiming at this difficult problem, a design method based on CFD (computational fluid dynamics) was proposed. After establishing the threedimensional model and meshing the intake system, RNG(renormalization-group) turbulence model was chosen to establish mathematical model of gas phase. Under some defined appropriate boundary conditions, the gas flow-field in air intake system was simulated by Fluent code. Additionally, in order to take the influence of air filter gauze, the structure of air filter was assumed to porous zone and the distribution of speed and pressures corresponding to the three methods were compared. And the air resistance was chosen as the testing criterion to evaluate the quality of this method. Results show that the second program, whose inlet resistance was least to be the best program. The method provides technological reference for the design of intake system.
Key words: air intake system    CFD    porous zone    optimized design
出版日期: 2011-08-28
:  TP 391.9  
服务  
把本文推荐给朋友
加入引用管理器
E-mail Alert
RSS
作者相关文章  
王治林
成凯
林源

引用本文:

王治林, 成凯, 林源. 基于CFD的车辆进气系统流场仿真与分析[J]. 工程设计学报, 2011, 18(4): 265-269.

WANG Zhi-Lin, CHENG Kai, LIN Yuan. Fluid simulation and analysis for automotive air intake systems based on CFD[J]. Chinese Journal of Engineering Design, 2011, 18(4): 265-269.

链接本文:

https://www.zjujournals.com/gcsjxb/CN/        https://www.zjujournals.com/gcsjxb/CN/Y2011/V18/I4/265

[1] 戚其松,李成刚,董青,陈钰浩,徐航. 起重机生命周期载荷谱预测及基于疲劳寿命的结构优化设计[J]. 工程设计学报, 2023, 30(3): 380-389.
[2] 张正峰,宋小雨,袁晓磊,陈文娟,张伟东. Al/CFRP混合薄壁结构耐撞性能可靠性优化设计[J]. 工程设计学报, 2022, 29(6): 720-730.
[3] 孙光明,王奕苗,万仟,弓堃,汪文津,赵坚. 考虑装配变形的精密机床床身优化设计[J]. 工程设计学报, 2022, 29(3): 318-326.
[4] 樊霄岳, 刘启, 官威, 朱云, 陈苏琳, 沈彬. 电磁微锻机构热效应模拟与实验研究[J]. 工程设计学报, 2022, 29(1): 66-73.
[5] 陈振, 李涛, 薛晓伟, 周阳, 敬爽, 陈言. 基于模糊综合评价法的可控震源振动器平板疲劳可靠性分析与优化[J]. 工程设计学报, 2021, 28(4): 415-425.
[6] 张锦, 刘佩珊, 殷玉枫. Y形旋转超声波马达的设计与动态特性分析[J]. 工程设计学报, 2021, 28(2): 248-254.
[7] 刘永江, 彭宣霖, 唐雄辉, 李华, 齐紫梅. 轴流散热风机共振失效分析与优化设计[J]. 工程设计学报, 2021, 28(2): 203-209.
[8] 魏巍, 林载盛. 基于RIR-MOO的定制产品优化设计方法研究[J]. 工程设计学报, 2020, 27(5): 592-599.
[9] 罗金武, 况雨春, 张锐, 陈花, 廖文玲, 李刚俊. 基于CFD-DEM耦合的水平井PDC钻头水力结构研究[J]. 工程设计学报, 2020, 27(5): 636-644.
[10] 孙月海, 唐二星. 弧齿锥齿轮基本参数优化设计[J]. 工程设计学报, 2020, 27(5): 616-624.
[11] 孙世峰, 高常青, 杨波, 徐征和. 基于试验设计与有限元仿真的辐射井水平钻机承载部件优化设计[J]. 工程设计学报, 2019, 26(6): 683-690.
[12] 钟功祥, 邹迪, 张兴. 基于CFD与ADAMS的三角转子气动机设计与仿真[J]. 工程设计学报, 2019, 26(3): 305-314.
[13] 杨迎新, 周坚, 黄奎林, 任海涛, 陈炼. 定向随钻扩孔PDC钻头优化设计及应用[J]. 工程设计学报, 2018, 25(6): 668-674.
[14] 万建成, 江明, 杨磊, 刘晨. 大截面碳纤维导线卡线器夹嘴优化设计[J]. 工程设计学报, 2018, 25(6): 675-682.
[15] 卢清华, 黄铭贤, 陈为林. 平面阻尼型欠驱动夹持器的多模式参数优化设计[J]. 工程设计学报, 2018, 25(6): 690-696.