Please wait a minute...
工程设计学报  2020, Vol. 27 Issue (3): 326-331    DOI: 10.3785/j.issn.1006-754X.2020.00.036
创新设计     
压电式提花经编机自升压节能控制电路设计
任雯1,2, 赖森财1,2
1.三明学院 装备智能控制福建省高校重点实验室, 福建 三明 365004
2.三明学院 机电工程学院, 福建 三明 365004
Design of self-boosting energy-saving control circuit for piezoelectric jacquard warp knitting machine
REN Wen1,2, LAI Sen-cai1,2
1.Key Laboratory of Fujian Colleges and Universities for Intelligent Control of Equipment, Sanming University, Sanming 365004, China
2.College of Mechanical and Electrical Engineering, Sanming University, Sanming 365004, China
 全文: PDF(931 KB)   HTML
摘要: 针对提花经编机压电贾卡针(piezo jacquard needle,PJN)的驱动电路存在功耗高、需要额外的高压电源等问题,设计了一种将自升压电路和工作电路集成为具有能量回收功能的新型PJN驱动电路。基于压电陶瓷晶片的压电方程和PJN结构,介绍了PJN的工作原理,详细分析了所提出的PJN驱动电路的工作模态,给出了电路模态转换的脉冲宽度调制(pulse width modulation,PWM)控制策略。新型PJN驱动电路采用储能电感器代替传统驱动电路的限流电阻器,不仅能够限制PJN的正向充电电流,减少能量损耗,而且可以利用从低压电源吸收的能量将PJN的低压供电电源自适应升压至工作状态所需的高压。为了验证电路的自升压过程,进行了仿真分析。仿真结果表明,该新型PJN驱动电路具有自升压功能,无须外接高压工作电源,仅需低压供电电源即可以高压驱动PJN,能有效降低功耗,实现节能环保,具有广阔的工程应用前景。
Abstract: In view of the problems of high power consumption and extra high-voltage power supply in the piezoelectric jacquard needle (PJN) drive circuit for jacquard warp knitting machine, a novel PJN driver circuit with energy recovery function which integrates the self-boost circuit and working circuit was proposed. Based on the piezoelectric equation of piezoelectric chip and PJN structure, the working principle of PJN was introduced, the working mode of the proposed PJN drive circuit was analyzed in detail, and the pulse width modulation (PWM) control strategy of circuit mode conversion was given. The new PJN drive circuit adopted the energy storage inductor to replace the current-limiting resistor of the traditional drive circuit, which could not only limit PJN's positive charging current and reduce energy loss, but also used the energy absorbed from the low-voltage power supply to boost the low-voltage power supply of PJN to the high voltage required by the working state adaptively. In order to verify the self-boosting process of the circuit, the simulation analysis was carried out. The simulation results showed that the novel PJN drive circuit had a self-boosting function, and no external high-voltage working power supply was needed. Low-voltage power supply is only needed to drive PJN with high voltage, which can effectively reduce power consumption and realize energy-saving, and has a broad prospect of engineering application.
收稿日期: 2019-07-17 出版日期: 2020-06-28
CLC:  TP 273  
基金资助: 国家自然科学基金资助项目(51576114);福建省工业引导性重点项目(2019H0034)
作者简介: 任雯(1979—),男,河南周口人,副教授,博士,从事分布式网络化控制系统和电路系统等研究,E-mail:auwren@foxmail.com,http://orcid.org/0000-0002-3605-7274。
服务  
把本文推荐给朋友
加入引用管理器
E-mail Alert
RSS
作者相关文章  

引用本文:

任雯, 赖森财. 压电式提花经编机自升压节能控制电路设计[J]. 工程设计学报, 2020, 27(3): 326-331.

REN Wen, LAI Sen-cai. Design of self-boosting energy-saving control circuit for piezoelectric jacquard warp knitting machine. Chinese Journal of Engineering Design, 2020, 27(3): 326-331.

链接本文:

https://www.zjujournals.com/gcsjxb/CN/10.3785/j.issn.1006-754X.2020.00.036        https://www.zjujournals.com/gcsjxb/CN/Y2020/V27/I3/326

[1] 胡坤, 蒋庆楠, 季晨光, 杨健, 李飞. 基于改进ESO的磁悬浮系统模型参考滑模控制[J]. 工程设计学报, 2022, 29(1): 82-91.
[2] 殷戎飞, 徐海黎, 田为广, 徐勋倩, 沈标. 框架式3D建筑打印机控制系统设计[J]. 工程设计学报, 2022, 29(1): 107-114.
[3] 郑雨辰, 鞠锋, 王旦, 孙敬滨, 王亚明, 陈柏. 航空发动机叶片检测机器人的设计与控制研究[J]. 工程设计学报, 2021, 28(5): 625-632.
[4] 王奔, 朱龙彪, 沈祖军, 陈小林. LYP1050轮转胶印机控制系统设计[J]. 工程设计学报, 2021, 28(1): 112-120.
[5] 王超, 孙文旭, 马晓静, 陈纪旸, 栾义忠, 马思乐. 基于模糊控制的HVPE生长设备温度控制系统[J]. 工程设计学报, 2020, 27(6): 765-770.
[6] 闻霞, 任雯, 赖森财, 曾显杰. 基于有限状态机模型的全自动烫印机控制系统设计[J]. 工程设计学报, 2020, 27(6): 771-780.
[7] 王颜, 刘净瑜, 李光, 张加波, 刘星, 周欣欣. 基于IGPS和麦克纳姆轮的AGV导航控制系统设计[J]. 工程设计学报, 2020, 27(5): 662-670.
[8] 陈继文, 王磊, 李鑫, 巩玉滨, 常国雷, 李凯凯. 基于RGV的环形横移式循环电梯创新设计[J]. 工程设计学报, 2020, 27(3): 317-325.
[9] 刘羽嘉, 潘滨, 李东泽, 李凤迪, 张迁, 孙丰刚, 兰鹏. 民宿无人值守智能管理系统设计与实现[J]. 工程设计学报, 2020, 27(3): 389-397.
[10] 秦永峰, 龚国芳, 王飞, 孙辰晨. 基于RBF神经网络的液黏调速离合器活塞位移控制器设计[J]. 工程设计学报, 2019, 26(5): 603-610.
[11] 郑华林, 杨舜波, 潘盛湖, 王超. 百叶片定长切料-自动排片控制系统研究[J]. 工程设计学报, 2019, 26(4): 461-468.
[12] 周结华, 代冀阳, 周继强, 张孝勇. 面向大型机场草坪的割草机器人路径规划及轨迹跟踪控制研究[J]. 工程设计学报, 2019, 26(2): 146-152.
[13] 段志强, 郭彦青, 王龙. 大惯量专用转台高精度控制研究[J]. 工程设计学报, 2019, 26(2): 162-169.