Please wait a minute...
浙江大学学报(工学版)
J4  2013, Vol. 47 Issue (6): 1043-1050    DOI: 10.3785/j.issn.1008-973X.2013.06.016
    
Optimization of swash-plate cross angle noise-reduction structure for swash-plate-type axial piston pump
XU Bing1, SONG Yue-chao1,2, YANG Hua-yong1
1. State Key Laboratory of Fluid Power and Mechatronic System, Zhejiang University, Hangzhou 310027, China| 2. Department of Science and Technology Development, Guangzhou Institute of Measurement and Testing Technology, Guangzhou 510000, China
Download:   PDF(0KB) HTML
Export: BibTeX | EndNote (RIS)      

Abstract  


In order to reduce the fluid-born noise of swash-plate-type axial piston pump in a large scale of operating conditions,the optimization of a novel noise-reduction structure, i.e., the swash-plate cross angle, was investigated. The swash-plate cross angle is attained by rotating the swash plate around the axis, which is simultaneously perpendicular to the axis of the driving shaft and the axis for the swash plate angle. With different cross angle, the pre-compression of the piston is different and thereby the flow rate and the fluid-born noise of the pump are changed. The working principle of the swash-plate cross angle noise-reduction structure was analyzed firstly, and then the corresponding simulation model was built and solved. Simulation shows that the flow ripple peak values decrease when the cross angle is more than 1°, while the values increase when the cross angle is less than -1 °. The flow ripple is decreased in all scale of pump delivery pressure when introducing the swash-plate cross angle with 1°. The flow ripple is the minimum when the swash-plate cross angle is 1°, especially the flow ripple can be decreased significantly when the pump speed is less than 1 000 r/min. The simulation model is validated by the test results obtained from the secondary source method.

Published: 22 November 2013
CLC:  TH 137.5  
Service
E-mail this article
Add to my bookshelf
Add to citation manager
E-mail Alert
RSS
Articles by authors
Cite this article:

XU Bing, SONG Yue-chao, YANG Hua-yong. Optimization of swash-plate cross angle noise-reduction structure for swash-plate-type axial piston pump. J4, 2013, 47(6): 1043-1050.

URL:

http://www.zjujournals.com/eng/10.3785/j.issn.1008-973X.2013.06.016     OR     http://www.zjujournals.com/eng/Y2013/V47/I6/1043


柱塞泵斜盘交错角降噪结构优化

为了使斜盘式轴向柱塞泵的流体噪声在各种工况下都能够得到降低,研究并优化了一种柱塞泵斜盘交错角新型降噪结构.柱塞泵斜盘交错角是斜盘绕与斜盘倾角轴和主轴同时垂直的轴旋转形成的角度.交错角不同,柱塞在配流盘过渡区压缩量就不同,从而影响柱塞泵出口流量脉动和流体噪声.基于斜盘交错角降噪原理,建立带斜盘交错角的柱塞泵流量脉动模型,仿真分析了不同斜盘旋转角度对柱塞泵流量脉动的影响,结果表明：交错角旋转角度大于1°,柱塞泵流量脉动上、下峰值降低|旋转角度小于-1°,柱塞泵流量脉动上、下峰值升高|交错角旋转1°可以得到较好的降噪效果,并能在全压力范围内降低柱塞泵流量脉动,转速小于1 000 r/min时可以明显降低柱塞泵流量脉动.仿真模型的有效性通过“二次源法”得到了证实.

［1］ 马吉恩.轴向柱塞泵流量脉动及配流盘优化设计研究［D］.杭州：浙江大学, 2005.

MA Ji-en. Study on flow ripple and valve plate optimization of axial piston pump ［D］. Hangzhou: ZheJiang University, 2005.

［2］ JOHANSSON A, LVANDER J, PALMBERG J-O. Experimental verification of cross angle for noise reduction in hydraulic piston pumps ［J］. Proceedings of the institution of mechanical engineers Part I: Journal Systems and Control Engineering,2007,221: 321-330.

［3］ ERICSON L. Measurement system for hydrostatic pump flow pulsations ［D］. Linkping: Linkping University, 2005.

［4］ MANRING Noah D, DONG Zhilin. The impact of using a secondary swash-plate angle within an axial piston pump［J］. Journal of Dynamic Systems, Measurement and Control,2004, 126: 65-74.

［5］ EDGE K A, DARLING J. The pumping dynamics of swash plate piston pumps ［J］. Journal of Dynamic System Measurement and Control – Transactions of the ASME, 1986,111(2)： 307-312.

［6］ EDGE K A, DARLING J. A theoretical model of axial piston pump flow ripple ［C］∥ Design modelling and control of pumps/First Bath International Fluid Power WSorkshop. ［S.l.］:［s.n.］,1988: 113-136.

［7］ EDGE K A, JOHNSTON D N. The secondary source method for the measurement of pump pressure ripple characteristics 1. Description of method ［J］. Proceedings of the Institution of Mechanical Engineers Part A—Journal of Power and Energy, 1990, 204 (1): 33-40.

［8］ EDGE K A, JOHNSTON D N. The secondary source method for the measurement of pump pressure ripple characteristics 2. Experimental results ［J］. Proceedings of the Institution of Mechanical Engineers Part A—Journal of Power and Energy, 1990, 204 (1): 41-46.


［9］ The International Organization for Standardization. ISO 10767-1-1996 Hydraulic Fluid Power-Determination of Pressure Ripple Levels Generated in System and Components Part 1: Precision method for pumps ［M］. London: British Standards Institution, 1996.

［10］ JOHNSTON D N. Measurement of positive displacement pump flow ripple and impedance ［J］. Journal of System and Control Engineering, 1996, 210（1): 61-74.
[1] XU Bing, ZHANG Jun-hui, YANG Hua-yong, YE Shao-gan. Simulation on noise reduction of tandem axial piston pump
utilizing indexing angle[J]. J4, 2013, 47(1): 94-101.
[2] LIU Wei, XU Bing, YANG Hua-yong, ZHU Xiao-jun. The characteristics of electrohydraulic flow matching control
systems for excavators based on LUDV multi-way valve[J]. J4, 2012, 46(8): 1360-1368.
[3] XU Bing, LIU Wei, YANG Hua-yong, ZHANG Sheng-feng. Experiment study on flow compensation of electro-hydraulic flow
matching control system in hydraulic excavator[J]. J4, 2012, 46(8): 1382-1389.
[4] ZHANG Bin, XU Bing, YANG Hua-Yong, et al. Study on control performance of digital piston pump based on virtual prototype technology[J]. J4, 2010, 44(1): 1-7.
[5] WANG Hang-Zhou, QIN Hua-Wei, YANG Can-Jun, et al. Fatigue life of PEEK poppet for deep-sea hydrothermal fluid sampling valve[J]. J4, 2010, 44(1): 14-18.