Please wait a minute...
J4  2013, Vol. 47 Issue (5): 895-900    DOI: 10.3785/j.issn.1008-973X.2013.05.023
能源工程     
四缸柴油机机体NVH性能改进
张焕宇,郝志勇,郑旭
浙江大学 能源工程学系, 浙江 杭州 310027    
Study of NVH performance improvement for a four-cylinder diesel engine body 
ZHANG Huan-yu, HAO Zhi-yong, ZHENG Xu
Department of Energy Engineering, Zhejiang University, Hangzhou, Zhejiang 310027, China
 全文: PDF  HTML
摘要:

为降低发动机辐射噪声,采用数值计算方法对某四缸柴油机机体的振动声学性能进行分析与改进设计.以有限元理论为指导,划分发动机有限元模型,建立整机的多体动力学模型以及声学模型.通过多体动力学和流体力学计算发动机动力学载荷,通过结构动力学计算机体的振动响应,通过声学计算预测机体的表面辐射噪声,并实验验证计算结果.根据计算得到的机体振动与声学特性,确定影响机体(NVH)性能的关键频率,有针对性的对机体进行低噪声优化设计.在改进模型的基础上重新建立发动机多体动力学模型,计算改进后机体的振动与声学性能.结果表明,通过优化设计,机体的辐射声功率级降低0.9 dBA.

Abstract:

Numerical methods were used to improve a four-cylinder engine body vibro-acoustic performance. Based on finite element theory, the engine body finite element model, multi-body dynamics model and acoustic model were established. Multi-body dynamics and fluid mechanics were used to calculate the engine dynamic load. Structural dynamics was used to calculate the engine body dynamic response. Acoustic method was used to calculate the engine body acoustic performance. All the calculated results were validated by experiments. Based on those results, the critical frequency of engine body was found. Hence, the engine body was redesigned to avoid resonance. After improvement, the NVH performance of engine body was recalculated. The results showed that, the radiated sound power level was reduced 0.9 dBA through optimized design.

出版日期: 2013-05-01
:  TK 422  
通讯作者: 郝志勇,男,教授,博导.     E-mail: haozy@zju.edu.cn
作者简介: 张焕宇(1985-)男,博士生,从事发动机虚拟设计与发动机振动噪声控制方面研究工作.E-mail:yyhuanyu@163.com
服务  
把本文推荐给朋友
加入引用管理器
E-mail Alert
RSS
作者相关文章  

引用本文:

张焕宇,郝志勇,郑旭. 四缸柴油机机体NVH性能改进[J]. J4, 2013, 47(5): 895-900.

ZHANG Huan-yu, HAO Zhi-yong, ZHENG Xu. Study of NVH performance improvement for a four-cylinder diesel engine body . J4, 2013, 47(5): 895-900.

链接本文:

http://www.zjujournals.com/eng/CN/10.3785/j.issn.1008-973X.2013.05.023        http://www.zjujournals.com/eng/CN/Y2013/V47/I5/895

[1] GERARD F, TOUMOUR M, MASRI N E, et a1. Numerical modeling of engine noise radiation through the use of acoustic transfer vectors- a case study [J]. SAE Paper, 2001,01:11514.
[2] LUA M H, JEN M U. Source identification and reduction of engine noise [J]. Noise Control Engineering Journal, 2010, 58(3): 251-258.
[3] SCHNEIDER M, LAHEY H P, STEDDENS C, et al. CAE process to eliminate powertrain noise and vibration [J]. SAE Paper, 2002,01:10459.
[4] 贾维新,郝志勇,杨金才. 基于形貌优化的低噪声油底壳研究[J].浙江大学学报:工学版,2007,41(5):770-773.
JIA Wei-xin, HAO Zhi-yong, YANG Jin-cai. Low noise design of oil pan based on topography optimization [J]. Chinese Mechanical Engineering,2007, 41(5):770-773.
[5] 张保成,左正兴.内燃机结构辐射噪声分析技术研究[J].车用发动机,2006,165(5):51-54.
ZHANG Bao-cheng, ZUO Zheng-xing. Research on the analytical techniques of radiant noise of ICE structure[J]. Vehicle Engine, 2006, 165(5):51-54.
[6] 杨陈.低噪声轻量化单缸柴油机的虚拟设计技术研究[D].杭州:浙江大学,2009:154-166.
YANG Chen. Research on light-weight and low-noise design for single cylinder diesel engine with virtual design technology [D]. Hangzhou: Zhejiang University,2009: 154166.
[7] RICCI S, RONCOSSI M, RIVOLA A. Model reduction of the flexible rotating crankshaft of a motorcycle engine cranktrain [J]. International Journal of Rotating Machinery, 2011, 143523: 19.
[8] 盛宏玉.结构动力学[M].合肥:合肥工业大学出版社,2005:161167.
[9] 孙军.内燃机曲轴-轴承系统摩擦学、刚度和强度的耦合分析[M]. 合肥,合肥工业大学出版社,2008: 1742.
[10] SUN Jun. Effect of lubrication status of bearing on crankshaft strenth[J]. Journal of Tribology, 2007, 129: 887-894.
[11] 郭磊,郝志勇,林琼.柴油机曲轴与气缸体系统动力学仿真研究[J]. 浙江大学学报:工学版,2007,41(5):780-784.
GUO Lei, HAO Zhi-yong, LIN Qiong. Dynamic simulation research on diesel engines cranktrain and block[J]. Journal of Zhejiang University, Engineering Science Edition,2007,41(5):780-784.
[12] 刘月辉. 基于虚拟技术的发动机噪声控制研究[D]. 天津:天津大学,2004: 8295.
LIU Yue-hui. Study on engine noise control based on virtual design[D]. Tianjin: Tianjin University, 2004:82-95.
[13] 贾维新,郝志勇,杨金才.虚拟预测方法在柴油机低噪声设计中的应用[J].浙江大学学报:工学版,2007,41(3):489-493.
JIA Wei-xin, HAO Zhi-yong, YANG Jin-cai. Application of virtual prediction method to low-noise diesel engine design[J]. Journal of Zhejiang University, Engineering Science Edition,2007, 41(3): 489-493.
[14] 李民,舒歌群,卫海桥.基于拓扑优化和形状优化的低噪声齿轮室罩盖设计[J].内燃机工程,2008,29(6):55-59.
LI Min, SHU Ge-qun, WEI Hai-qiao. Design of a low noise engine gear cover based on topology and shape optimization [J]. Chinese Internal Combustion Engine Engineering, 2008, 29(6): 55-59.
[15] 万欣,林大渊.内燃机设计[M].天津:天津大学出版社,1988:230-237.

[1] 张焕宇, 郝志勇. 飞轮壳结构刚度对机体NVH性能的影响[J]. J4, 2013, 47(2): 261-266.