Please wait a minute...
浙江大学学报(工学版)
机械与能源工程     
TBM支撑-推进-换步机构的拓扑结构及运动特性分析
王凯, 杨玉虎, 黄田, 牛文文, 贺飞
1. 天津大学 机构理论与装备设计教育部重点实验室,天津 300350; 2. 中铁隧道装备制造有限公司, 河南 郑州 450016
Topological structure and kinematic characteristic analysis of TBM gripping-thrusting-regripping mechanism
WANG Kai, YANG Yu-hu, HUANG Tian, NIU Wen-wen, HE Fei
1. Key Laboratory of Mechanism Theory and Equipment Design of Ministry of Education, Tianjin University, Tianjin 300350, China; 2. China Railway Tunnelling Equipment Co. Ltd, Zhengzhou 450016, China)
 全文: PDF(2568 KB)   HTML
摘要:

简要介绍机构的拓扑结构与工作原理,分析机构的拓扑结构在不同工况下对整机性能的影响,建立机构拓扑结构设计应遵循的基本准则.针对机构的结构特征,建立机构在线调向工况下的运动方程.以某开敞式硬岩掘进装备(TBM)(刀盘直径为8 m)支撑-推进-换步机构样机为例,结合TBM在线调向作业的运动仿真,建立机构的推进油缸、调向油缸及作业参数间的运动方程,为深入开展支撑-推进-换步机构的创新设计以及精准在线调向提供有效的计算方法.

Abstract: The topology configuration and working principle of the mechanism were briefly introduced. On this foundation, the influences of the mechanism topology configuration upon engine performance system were systematically analyzed under different conditions. The design criteria of the mechanism topology configuration were established. According to the structural characteristics of the mechanism, the motion equation of the mechanism was established in online steering. Finally, taking the gripping-thrusting-regripping mechanism of open TBM (cutterhead diameter of 8 m) as an example, the motion equations of mechanism between propel cylinders, steering cylinders and operating parameters were established by the motion simulation of TBM online steering. The research content provides an effective calculation method for the gripping-thrusting-regripping mechanism innovative design and precision online steering.
出版日期: 2017-06-11
CLC:  TH 11  
基金资助:

国家“973”重点基础研究规划资助项目(2013CB035403);国家“863”高技术研究发展计划资助项目(2012AA04).

通讯作者: 杨玉虎,男,教授. ORCID:0000-0002-3915-0212.     E-mail: yangyuhu@tju.edu.cn
作者简介: 王凯(1989—),男,硕士生,从事机构学研究. ORCID:0000-0002-6946-6605. E-mail:wangkaigx@163.com
服务  
把本文推荐给朋友
加入引用管理器
E-mail Alert
作者相关文章  

引用本文:

王凯, 杨玉虎, 黄田, 牛文文, 贺飞. TBM支撑-推进-换步机构的拓扑结构及运动特性分析[J]. 浙江大学学报(工学版), 10.3785/j.issn.1008-973X.2017.06.011.

WANG Kai, YANG Yu-hu, HUANG Tian, NIU Wen-wen, HE Fei. Topological structure and kinematic characteristic analysis of TBM gripping-thrusting-regripping mechanism. JOURNAL OF ZHEJIANG UNIVERSITY (ENGINEERING SCIENCE), 10.3785/j.issn.1008-973X.2017.06.011.

参考文献(References):
[1] 陆燕荪.中国制造任重道远装备中国责无旁贷中国装备制造业现状与发展战略[J].机械工程学报,2007,43(1): 2-6.
LU Yan-sun. Current situation and development strategy of Chinese equipment manufacturing industry [J]. Chinese Journal of Mechanical Engineering,2007,43(1): 2-6.
[2] 张镜剑.隧道掘进机在我国应用的进展[J].岩石力学与工程学报,2007,26(2):226-238.
ZHANG Jing-jian. Advances in tunnel boring machine application in China [J]. Chinese Journal of Rock Mechanics and Engineering,2007,26(2): 226-238.
[3] YANG H Y, SHI H, GONG G F. Electro-hydraulic proportional control of thrust system for shield tunneling machine [J]. Automation in Construction,2009,18(7): 950-956.
[4] YANG H Y, SHI H, GONG G F. Motion control of thrust system for shield tunneling machine [J]. Journal of Central South University of Technology,2010,17(3):537-543.
[5] SHI H, YANG H Y, GONG G F, et al. Determination of the cutterhead torque for EPB shield tunneling machine [J]. Automation in Construction,2011,20(8):1087-1095.
[6] ZHAO Y, WANG H, YU H D, et al. A stiffness matching based evaluation approach for compliance of mechanical systems in shield tunneling machines [J]. Science China Technological Sciences, 2012, 55(10):2926-2935.
[7] DAVID T C, SEATTLE, WASH. Earth boring machine and method: 3861748 [P]. 1975-01-21.
[8] 杜彦良,杜立杰著.全断面隧道掘进机系统原理与集成设计[M].武汉:华中科技大学出版社,2011.
[9] BERNHARD M,et al. Hard rock tunnel boring machines [M]. Beilin: Ernst and Sohn,2008.
[10] 王梦恕.开敞式TBM在铁路长隧道特硬岩、软岩地层的施工技术[J].土木工程学报,2005,38(5): 54-58.
WANG Meng-shu. Construction technique open TBM for long railway tunnels in very hard or soft rock strata [J]. China Civil Engineering Journal,2005,38(5):54-58.
[11] The Robbins Company. Service manual MB 332-335&336 preliminary issue [M]. Solon: the Robbins Company,2009.
[12] 周建军,杨振兴.深埋长隧道TBM施工关键问题探讨[J].岩土力学,2014,35(增2): 299-305.
ZHOU Jian-jun,YANG Zheng-xing. Discussion on key issues of TBM construction for long and deep tunnels [J]. Rock and Soil Mechanics,2014,35(Suppl.2):299-305.
[13] WANG K,YANG Y H,SHEN Z G,et al. Research on the experimental test system of TBM gripping-thrusting-regripping mechanism [C] ∥ 2016 MESA International Conference of IEEE. Auckland: IEEE,2016:1-5.
[14] GAO X X,YANG Y H. Finite element modeling of gripping-thrusting-regripping mechanism of TBM based on SAMCEF [C] ∥ 8th International Conference on Intelligent Robotics and Applications. Portsmouth: ICIRA,2015: 481-488.
[15] 牛文文.TBM支撑推进机构掘进性能分析[D].天津:天津大学,2014.
NIU Wen-wen. Analysis on excavating performance of gripper and thrust mechanism of TBM [D]. Tianjin: Tianjin University,2014.
[16] HUANG T,WANG X L,LIU H T,et al. Force analysis of a TBM gripping-thrusting-regripping mechanism[J]. Mechanism and Machine Theory,2016,98: 101-113.
[17] 余发国,高峰,史巧硕.基于GF集的锻造操作机构型方法[J].机械工程学报,2008,44(11): 152-159.
YU Fa-guo, GAO Feng, SHI Qiao-shuo. Type synthesis for forging manipulators based on GF set [J]. Chinese Journal of Mechanical Engineering,2008,44(11):152-159.
[18] GE H,GAO F. Type design for heavy-payload forging manipulators [J]. Chinese Journal of Mechanical Engineering,2012,25(2): 197-205.
[19] TASI L W,JOSHI S. Kinematic analysis of 3-DOF position mechanisms for use in hybrid kinematic machines [J]. Journal of Mechanical Design,2002,124(2):245-253.
[20] YAN C Y,GAO F,ZHANG Y. Kinematic modeling of a serial-parallel forging manipulator with application to heavy-duty manipulations [J]. Mechanics Based Design of Structures and Machines,2010,38(1): 105-129.
[21] HUANG T,LIU H T,CHETWYND D G. Generalized jacobian analysis of lower mobility manipulators [J]. Mechanism and Machine Theory,2011,46(6):831-844.
[22] 黄真,赵永生,赵铁石.高等空间机构学[M].北京:高等教育出版社,2006: 116-127.

[1] 李伟达,王柱,张虹淼,李娟,顾洪. 床式步态康复训练系统机构设计[J]. 浙江大学学报(工学版), 2021, 55(5): 823-830.
[2] 陈英龙,宋甫俊,张军豪,宋伟,弓永军. 基于临场感的遥操作机器人共享控制研究综述[J]. 浙江大学学报(工学版), 2021, 55(5): 831-842.
[3] 李伟达,李娟,李想,张虹淼,顾洪,史逸鹏,张浩杰,孙立宁. 欠驱动异构式下肢康复机器人动力学分析及参数优化[J]. 浙江大学学报(工学版), 2021, 55(2): 222-228.
[4] 李研彪,徐涛涛,郑航,王泽胜. 含球面副间隙的空间并联机构动态特性[J]. 浙江大学学报(工学版), 2020, 54(2): 348-356.
[5] 谭芳芳,朱俊江,严天宏,高志强,何岭松. 基于GA-WPT-ELM的6061铝合金表面粗糙度预测[J]. 浙江大学学报(工学版), 2020, 54(1): 40-47.
[6] 黄智,贾臻杰,邓涛,刘永超,杜丽. 基于支持向量机的静压转台热误差补偿[J]. 浙江大学学报(工学版), 2019, 53(8): 1594-1601.
[7] 高阳,方成刚,蒋贤辉. 水泥3D打印喷头中浆体的流动分析[J]. 浙江大学学报(工学版), 2019, 53(3): 420-426.
[8] 周瑾,高天宇,陈怡,席鸿皓. 采用动力测试的双转子卧螺离心机模型修正[J]. 浙江大学学报(工学版), 2019, 53(2): 241-249.
[9] 张铭奎, 程文明, 刘放. 助力外骨骼负载特征与驱动特征耦合效应[J]. 浙江大学学报(工学版), 2017, 51(4): 807-816.
[10] 王明斗, 陶建峰, 覃程锦, 刘成良. 空间余量最优的拼装机轨迹规划[J]. 浙江大学学报(工学版), 2017, 51(3): 453-460.
[11] 王扬威, 闫勇程, 刘凯, 赵东标. 仿生机器魟鱼研制与游动性能实验研究[J]. 浙江大学学报(工学版), 2017, 51(1): 106-112.
[12] 童水光, 贾亚萍, 余跃, 唐宁, 谢国生, 沈强, 从飞云. 动点间歇性冲击变形计算方法的研究[J]. 浙江大学学报(工学版), 2017, 51(1): 124-130.
[13] 黄伟迪,甘春标,杨世锡. 一类高速电主轴的动力学建模及振动响应分析[J]. 浙江大学学报(工学版), 2016, 50(11): 2195-2206.
[14] 黄伟,王家序,徐涛,肖科,李俊阳,吴会超. 金属橡胶复合齿轮副振动特性分析及实验[J]. 浙江大学学报(工学版), 2016, 50(11): 2231-2238.
[15] 戚玉轩, 邱清盈, 冯培恩, 李立新. 机械结构组合对称概念体系及应用[J]. 浙江大学学报(工学版), 2016, 50(10): 1889-1901.