Please wait a minute...
浙江大学学报(工学版)  2018, Vol. 52 Issue (2): 247-254    DOI: 10.3785/j.issn.1008-973X.2018.02.006
机械与动力工程     
磨齿机电主轴热特性及热误差建模
谢杰1, 黄筱调1,2, 方成刚1,2, 周宝仓3, 陆宁1
1. 南京工业大学 机械与动力工程学院, 江苏 南京 210009;
2. 南京工业大学 江苏省工业装备数字制造及控制技术重点实验室, 江苏 南京 210009;
3. 重庆大学 机械传动国家重点实验室, 重庆 400044
Thermal characteristics and thermal error modeling analysis for motorized spindle of gear grinding machine tool
XIE Jie1, HUANG Xiao-diao1,2, FANG Cheng-gang1,2, ZHOU Bao-cang3, LU Ning1
1. School of Mechanical and Power Engineering, Nanjing Tech University, Nanjing 210009, China;
2. Jiangsu Key Laboratory of Digital Manufacturing for Industrial Equipment and Control Technology, Nanjing Tech University, Nanjing 210009, China;
3. State Key Laboratory of Mechanical Transmission, Chongqing University, Chongqing 400044, China
 全文: PDF(1995 KB)   HTML
摘要:

针对磨齿机在磨削加工时,电主轴存在热致误差等问题,提出基于模糊神经网络(FNN)建立电主轴热误差模型的方法.分析电主轴内部的热生成和热传递机理,得到内部的传热规律.通过计算热载荷和边界条件,利用有限元分析(FEA)软件对电主轴系统的温度场和热变形进行数值模拟,得到电主轴系统中温升和热变形最大的部位.通过电主轴热误差实验获得温度和热变形数据,分别训练模糊神经网络和BP神经网络,建立温度场和热变形之间的热误差模型,对主轴热误差进行预测.结果显示:在电主轴径向热误差预测模型中,模糊神经网络模型和BP模型的建模精度分别为96.74%和89.77%.这表明模糊神经网络模型建立的热误差模型,在拟合和预测精度上优于BP神经网络模型.

Abstract:

A new modeling method based on fuzzy neural network (FNN) was proposed to solve the problem of the thermal error caused by the motorized spindle in the grinding machining process. The internal heat generating and transfer mechanism of the spindle were analyzed to reveal the heat transfer law. The temperature field and the thermal deformation of the spindle system were numerically simulated by finite element analysis (FEA) software with the given thermal load and boundary condition. The maximum risen temperature and the largest thermal deformation were obtained. Fuzzy neural network model and BP neural network model were trained respectively, through acquiring temperature and thermal deformation values of the spindle in the thermal error experiment. The thermal error model between temperature field and its thermal deformation was established to predict the thermal error of the spindle. Results show that the modeling accuracy of the fuzzy neural network model and the BP model are 96.74% and 89.77% respectively in the prediction model of the radial thermal error. The thermal error model of FNN model is superior to that of BP neural network for the fitting and forecasting accuracy.

收稿日期: 2016-12-20 出版日期: 2018-03-09
CLC:  TH161  
基金资助:

国家自然科学基金重点资助项目(51635003).

通讯作者: 黄筱调,男,教授,博导.orcid.org/0000-0002-3521-5808.     E-mail: njtechhxd@163.com
作者简介: 谢杰(1992-),男,硕士生,从事数控理论及技术等研究.orcid.org/0000-0001-6704-6669.E-mail:tzxiejie1992@163.com
服务  
把本文推荐给朋友
加入引用管理器
E-mail Alert
作者相关文章  

引用本文:

谢杰, 黄筱调, 方成刚, 周宝仓, 陆宁. 磨齿机电主轴热特性及热误差建模[J]. 浙江大学学报(工学版), 2018, 52(2): 247-254.

XIE Jie, HUANG Xiao-diao, FANG Cheng-gang, ZHOU Bao-cang, LU Ning. Thermal characteristics and thermal error modeling analysis for motorized spindle of gear grinding machine tool. JOURNAL OF ZHEJIANG UNIVERSITY (ENGINEERING SCIENCE), 2018, 52(2): 247-254.

链接本文:

http://www.zjujournals.com/eng/CN/10.3785/j.issn.1008-973X.2018.02.006        http://www.zjujournals.com/eng/CN/Y2018/V52/I2/247

[1] BRYAN J. International status of thermal error research[J].CIRP Annals-Manufacturing Technology, 1990,39(2):645-656.
[2] 姚晓栋, 黄奕乔, 马晓波,等. 基于时间序列算法的数控机床热误差建模及其实时补偿[J]. 上海交通大学学报, 2016, 50(5):673-679. YAO Xiao-dong, HUANG Yi-qiao, MA Xiao-bo, et al. Thermal error modeling and real-time compensation of CNC machine tools based on time series method[J]. Journal of Shanghai Jiaotong University, 2016, 50(5):673-679.
[3] 拓占宇, 黄奕乔, 沈牧文,等. 基于3次样条插值的数控机床几何与热复合定位误差建模[J]. 上海交通大学学报, 2016, 50(5):668-672. TUO Zhan-yu, HUANG Yi-qiao, SHEN Mu-wen, et al. Modeling of geometric and thermal complex positioning error of CNC machine tools based on cubic spline interpolation[J]. Journal of Shanghai Jiaotong University, 2016, 50(5):668-672.
[4] LI J W, ZHANG W J, YANG G S, et al. Thermal error modeling for complex physical systems:the-state-of-arts review[J]. The International Journal of Advanced Manufacturing Technology, 2009, 42(1):168-179.
[5] CREIGHTON E, HONEGGER A, TULSIAN A,et al. Analysis of thermal errors in a high-speed micro-milling spindle[J]. International Journal of Machine Tools & Manufacture, 2010, 50(4):386-393.
[6] MIAN N S, FLETCHER S, LONGSTAFF A P, et al. Efficient estimation by FEA of machine tool distortion due to environmental temperature perturbations[J]. Precision Engineering, 2013, 37(2):372-379.
[7] ZHAOC, GUAN X. Thermal analysis and experimental study on the spindle of the high-speed machining Center[J]. Aasri Procedia, 2012, 1(4):207-212.
[8] MA C, MEI X, YANG J, et al. Thermal characteristics analysis and experimental study on the high-speed spindle system[J]. The International Journal of Advanced Manufacturing Technology, 2015, 79(1):469-489.
[9] DU Z C, YAO S Y, YANG J G. Thermal behavior analysis and thermal error compensation for motorized spindle of machine tools[J]. International Journal of Precision Engineering and Manufacturing, 2015, 16(7):1571-1581.
[10] HAN J, WANG L, WANG H, et al. A new thermal error modeling method for CNC machine tools[J]. The International Journal of Advanced Manufacturing Technology, 2012, 62(1):205-212.
[11] 王时龙, 杨勇, 周杰,等. 大型数控滚齿机热误差补偿建模[J]. 中南大学学报:自然科学版, 2011, 42(10):3066-3072. WANG Shi-long, YANG Yong, ZHOU Jie, et al. Modeling of thermal error compensation of large-scale numerical control gear hobbing machine[J]. Journal of Central South University:Science and Technology, 2011, 42(10):3067-3072.
[12] 李逢春, 王海同, 李铁民. 重型数控机床热误差建模及预测方法的研究[J]. 机械工程学报, 2016, 52(11):154-160. LIFeng-chun, WANG Hai-tong, LI Tie-min. Research on thermal error modeling and prediction of heavy CNC machine tools[J]. Journal of Mechanical Engineering, 2016, 52(11):154-160.
[13] LI Y, ZHAO W. Axial thermal error compensation method for the spindle of a precision horizontal machining center[C]//IEEE International Conference on Mechat-ronics and Automation. Chengdu:IEEE, 2012:2319-2323.
[14] YANG J, SHI H, FENG B, et al. Thermal error modeling and compensation for a high-speed motorized spindle[J]. The International Journal of Advanced Manufacturing Technology, 2015, 77(5):1005-1017.
[15] TAN B, MAO X, LIU H, et al. A thermal error model for large machine tools that considers environmental thermal hysteresis effects[J]. International Journal of Machine Tools & Manufacture, 2014, 82-83(7):11-20.
[16] YAN J Y, YANG JG. Application of synthetic grey correlation theory on thermal point optimization for machine tool thermal error compensation[J]. The International Journal of Advanced Manufacturing Technology, 2009, 43(11):1124-1132.
[17] 张毅, 杨建国. 基于灰色理论预处理的神经网络机床热误差建模[J]. 机械工程学报, 2011, 47(7):134-139. ZHANG Yi, YANGJian-guo. Modeling for machine tool thermal error based on grey model preprocessing neural network[J]. Journal of Mechanical Engineering, 2011, 47(7):134-139.
[18] ABDULSHAHED A M, LONGSTAFF A P, FLETCHERS, et al. Thermal error modelling of machine tools based on ANFIS with fuzzy c-means clustering using a thermal imaging camera[J]. Applied Mathematical Modelling, 2015, 39(7):1837-1852.
[19] HUANG Y, ZHANG J, LI X, et al. Thermal error modeling by integrating GA and BP algorithms for the high-speed spindle[J]. The International Journal of Advanced Manufacturing Technology, 2014, 71(9):1669-1675.
[20] YANG J, SHI H, FENG B, et al. Applying neural network based on fuzzy cluster pre-processing to thermal error modeling for coordinate boring machine[J]. Procedia Cirp, 2014, 17:698-703.
[21] 马驰, 赵亮, 梅雪松,等. 基于粒子群算法与BP网络的机床主轴热误差建模[J]. 上海交通大学学报, 2016, 50(5):686-695. MA Chi, ZHAO Liang, MEI Xue-song, et al. Thermal error modeling of machine tool spindle based on particle swarm optimization and neural network[J]. Journal of Shanghai Jiaotong University, 2016, 50(5):686-695.
[22] 徐文龙. 高速铣削电主轴热特性分析及热误差补偿方法研究[D]. 广东:广东工业大学, 2016. XU Wen-long. Thermal characteristics analysis and thermal error compensation method of high-speed milling motor spindle[D]. Guangdong:Guangdong University of technology, 2016.
[23] 王志强. 基于ANSYS的高速电主轴温度场分析[D].兰州:兰州理工大学, 2011. WANG Zhi-qiang. Temperature field analysis of motorized spindle based on ANSYS[D]. Lanzhou:Lanzhou University of Technology, 2011.
[24] HARRIST A. Rolling Bearing Analysis[M]. 3th ed. Wiley:CRC Press, 1991:540-560.

[1] 曹云, 席占稳, 王炅, 聂伟荣, 孔南. UV-LIGA工艺误差对MEMS万向惯性开关性能的影响[J]. 浙江大学学报(工学版), 2017, 51(9): 1815-1823.
[2] 马驰,杨军,赵亮,梅雪松,施虎,王新孟. 高速主轴系统热特性分析与实验[J]. 浙江大学学报(工学版), 2015, 49(11): 2092-2102.