Please wait a minute...
浙江大学学报(工学版)
机械工程     
一类高速电主轴的动力学建模及振动响应分析
黄伟迪,甘春标,杨世锡
浙江大学 机械工程学院,浙江 杭州 310027
Dynamic modeling and vibration response analysis of high speed motorized spindle
HUANG Wei di, GAN Chun biao, YANG Shi xi
College of Mechanical Engineering, Zhejiang University, Hangzhou 310027, China
 全文: PDF(2013 KB)   HTML
摘要:

为了减小电主轴在高转速下的振动,基于有限元梁理论建立电主轴动力学模型,同时分别利用Hertz接触理论与Maxwell应力张量法给出球轴承非光滑接触力与不平衡磁拉力.通过计算不同转速、轴承游隙和初始偏心距下电主轴振动响应的分岔图,分析电主轴受球轴承接触力与不平衡磁拉力作用而产生的动力学现象.结果表明,在轴承接触力与不平衡磁拉力作用下,电主轴振动响应将出现倍周期分岔、拟周期分岔和倒分岔等现象,导致电主轴产生复杂的周期、拟周期与混沌振动之间的转迁.通过合理调整转速、轴承游隙和转子初始偏心距等参数,可以避免电主轴的剧烈振动.

Abstract:

A dynamic model of the high speed motorized spindle was built based on the finite element beam theory in order to reduce the vibration of the motorized spindle at high speed. Both the ball bearing contact force by Hertz contact theory and the unbalanced magnet pull using the Maxwell stress tensor method were considered. The bifurcation diagrams of vibration response of the motorized spindle were obtained numerically at different rotation speed, bearing clearance and initial eccentricity distance. Then the dynamic bifurcation phenomena caused by the ball bearing contact force and the unbalanced magnet pull were analyzed.  Results show that, period-doubling bifurcation, quasi-period bifurcation and inverse bifurcation will occur in response to the ball bearing contact force and the unbalanced magnet pull, leading to the complicated transition from periodic to quasiperiodic or chaotic vibration of the motorized spindle. Severe vibration can be  effectively avoided by adjusting the initial eccentricity distance, the bearing clearance or the rotation speed of the motorized spindle.

出版日期: 2016-11-01
:  TH 113  
基金资助:

国家自然科学基金资助项目(11172260,11372270).

通讯作者: 甘春标,男,教授. ORCID: 0000-0002-6597-5605.     E-mail: cb_gan@zju.edu.cn
作者简介: 黄伟迪(1989-),男,博士生,从事转子动力学等研究. ORCID:0000-0002-1311-423X. E-mail:jl_huangweidi@163.com
服务  
把本文推荐给朋友
加入引用管理器
E-mail Alert
RSS
作者相关文章  

引用本文:

黄伟迪,甘春标,杨世锡. 一类高速电主轴的动力学建模及振动响应分析[J]. 浙江大学学报(工学版), 10.3785/j.issn.1008-973X.2016.11.022.

HUANG Wei di, GAN Chun biao, YANG Shi xi. Dynamic modeling and vibration response analysis of high speed motorized spindle. JOURNAL OF ZHEJIANG UNIVERSITY (ENGINEERING SCIENCE), 10.3785/j.issn.1008-973X.2016.11.022.

链接本文:

http://www.zjujournals.com/eng/CN/10.3785/j.issn.1008-973X.2016.11.022        http://www.zjujournals.com/eng/CN/Y2016/V50/I11/2195

[1] ABELE E, ALTINTAS Y, BRECHER C. Machine tool spindle units  [J]. CIRP AnnalsManufacturing Technology, 2010, 59(2): 781-802.
[2] CAO Y, ALTINTAS Y. A general method for the modeling of spindlebearing systems [J]. Journal of Mechanical Design, 2004, 126(6): 1089-1104.
[3] GAGNOL V, LE T P, RAY P. Model identification of spindletool unit in highspeed machining[J]. Mechanical Systems and Signal Processing, 2011, 25(7): 2388-2398.
[4] CAO H R, HOLKUP T, ALTINTAS Y. A comparative study on the dynamics of high speed spindles with respect to different preload mechanisms [J]. International Journal of Advanced Manufacturing Technoloy, 2011, 57(9): 871-883.
[5] JONES A. A general theory for elastically constrained ball and radial roller bearings under arbitrary load and speed conditions [J]. Journal of Fluids Engineering, 1960, 82(2): 309-320.
[6] HARRIS T A. Rolling Bearing Analysis\[M\]. New York:Willey, 1991.
[7] HARSHA S P. Nonlinear dynamic responses of a balanced rotor supported by rolling element bearings due to radial internal clearance effect [J]. Mechanism and Machine Theory, 2006, 41(6): 688-706.
[8] 孟杰,陈小安,合烨. 高速电主轴电动机—主轴系统的机电耦合动力学建模[J]. 机械工程学报,2007, 43(12): 160-165.
MENG Jie, CHEN Xiaoan, HE Ye. Electromechanical coupled dynamical modeling of high speed motorized spindles motorspindle subsystem [J]. Chinese Journal of Mechanical Engineering, 2007, 43(12): 160-165.
[9] 杨丹,甘春标,杨世锡,等. 一类初弯曲转子的裂纹碰摩故障响应分析[J]. 浙江大学学报:工学版,2014, 48(8): 1496-1501.
YANG Dan, GAN Chunbiao, YANG Shixi, et al. Analysis on response of a rotor with initial bend deformation under coupling fault of crack and rubimpact [J]. Journal of Zhejiang University :Engineering Science, 2014, 48(8): 1496-1501.
[10] 李松生,陈晓阳,张刚,等. 超高速时电主轴轴承的动态支承刚度分析[J].机械工程学报,2006, 42(11): 60-65.
LI Songsheng, CHEN Xiaoyang, ZHANG Gang, et al. Analyses of dynamic supporting stiffness about spindle bearings at extra highspeed in electric spindles [J].Chinese Journal of Mechanical Engineering, 2006, 42(11): 60-65.
[11] NELSON H D. A finite rotating shaft element using timoshenko beam theory [J]. ASME Journal of Mechanical Design, 1980, 102(4): 793-803.
[12] HARSHA S P, KANKAR P K. Stability analysis of a rotor bearing system due to surface waviness and number of balls [J].International Journal of Mechanical Sciences. 2004, 46(7): 1057-1081.
[13] CHENG M, MENG G, WU B Y. Nonlinear dynamics of a rotorball bearing system with Alford force [J]. Journal of Vibration and Control, 2011, 18(1): 17-27.
[14] BAI C Q, ZHANG H Y, XU Q Y. Effects of axial preload of ball bearing on the nonlinear dynamic characteristics of a rotorbearing system[J]. Nonlinear Dynamics, 2008, 53(3): 173-190.
[15] GUO D, CHU F, CHEN D. The unbalanced magnetic pull and its effects on vibration in a threephase generator with eccentric rotor [J]. Journal of Sound and Vibration, 2002, 254(2): 297312.
[16] 岳二团,甘春标,杨世锡. 气隙偏心下永磁电机转子系统的振动特性分析[J].振动与冲击,2014, 33(8): 29-34.
YUE Ertuan, GAN Chunbiao, YANG Shixi. Vibration characteristics analysis of a rotor for a permanent magnet motor with AirGap Eccentricity[J].Journal of Vibration and Shock, 2014, 33(8): 29-34.
[17] GAN C B, WANG Y H, YANG S X, et al. Nonparametric modeling and vibration analysis of uncertain Jeffcott rotor with disc offset [J]. International Journal of Mechanical Sciences, 2014, 78(1):126-134.

[1] 王扬威, 闫勇程, 刘凯, 赵东标. 仿生机器魟鱼研制与游动性能实验研究[J]. 浙江大学学报(工学版), 2017, 51(1): 106-112.
[2] 黄伟,王家序,徐涛,肖科,李俊阳,吴会超. 金属橡胶复合齿轮副振动特性分析及实验[J]. 浙江大学学报(工学版), 2016, 50(11): 2231-2238.
[3] 程卫东,赵德尊 . 用于滚动轴承转频估计的EMD软阈值降噪算法[J]. 浙江大学学报(工学版), 2016, 50(3): 428-436.
[4] 田红亮,余媛,张屹. 机床支撑地脚结合部法向粗糙接触建模[J]. 浙江大学学报(工学版), 2015, 49(11): 2111-2118.
[5] 魏义敏, 杨世锡, 甘春标. 变截面阶梯杆中的纵波传播特性实验[J]. 浙江大学学报(工学版), 2015, 49(6): 1146-1153.
[6] 杨依领,娄军强,魏燕定,傅雷,田埂,赵晓伟. 综合模态控制力下压电致动器的优化布局[J]. 浙江大学学报(工学版), 2015, 49(5): 841-847.
[7] 杨丹, 甘春标, 杨世锡, 王跃华. 一类初弯曲转子的裂纹-碰摩故障响应分析[J]. 浙江大学学报(工学版), 2014, 48(8): 1496-1501.
[8] 李强, 刘淑莲, 于桂昌, 潘晓弘, 郑水英. 非线性转子-轴承耦合系统润滑及稳定性分析[J]. J4, 2012, 46(10): 1729-1736.
[9] 钟志贤, 祝长生. 横向裂纹多盘柔性转子系统的动力学特性[J]. J4, 2012, 46(10): 1839-1845.
[10] 王跃华,甘春标 ,杨世锡,雷华. 有界噪声激励下Hénon-Heiles系统响应的降噪分析[J]. J4, 2011, 45(11): 1895-1899.