Please wait a minute...
工程设计学报
工程设计学报  2018, Vol. 25 Issue (3): 346-352,366    DOI: 10.3785/j.issn.1006-754X.2018.03.014
整机和系统设计     
高速精密轧辊磨头主轴驱动控制系统设计
殷松, 吴怀超, 杨绿, 晏文孟, 沈瑞芳
贵州大学 机械工程学院, 贵州 贵阳 550025
Design of spindle drive control system of high-speed precision roll grinding head
YIN Song, WU Huai-chao, YANG Lü, YAN Wen-meng, SHEN Rui-fang
School of Mechanical Engineering, Guizhou University, Guiyang 550025, China
 全文: PDF(1999 KB)   HTML
摘要：

高速轧辊磨床是冶金生产领域一种不可或缺的重要设备，它是基于高精度和稳定可靠的电气控制系统来实现对磨削过程的准确控制。针对一种砂轮线速度在80 m/s以上的高速轧辊磨床，以FX3UPLC作为控制器，采用与PLC（programmable logic controller，可编程逻辑控制器）标准配套的A/D及D/A特殊功能模块，组成PLC模拟量控制系统，设计了基于FX3UPLC和变频器控制的高速精密轧辊磨头主轴驱动控制系统。介绍了高速精密轧辊磨头运行时的控制要求及磨头主轴电机变频调速控制系统的组成、控制方案及信号处理方法，设计了硬件电路、电机速度控制梯形图及系统通信程序。利用组态王软件开发了上位机监控界面，通过上位机组态界面输入框设定电机转速，加入模拟量编码器作为主轴电机转速反馈传感器，引入PID速度闭环控制系统，使得电机能够在给定转速下稳定运行。系统采用PLC对模拟量信号进行实时采集，经数模计算和反馈，实现轧辊磨头主轴系统各过程变量的实时监测和主轴电机输出转速的在线调整。该系统运行稳定，具有较好的抗干扰性能，保证了高速精密轧辊磨头连续可靠、安全高效的运行。
关键词： 高速轧辊磨床;  变频器;  PLC;  在线监控    
Abstract:

High-speed roll grinder, which is based on high precision and stabilization electrical control system, is an indispensable equipment in steel production fields to achieve accurate control of the grinding process. Aiming at a kind of high-speed roll grinder whose grinding speed was more than 80 m/s, with the FX3UPLC as controller, the PLC (programmable logic controller) analog control unit was formed by using the supporting standard A/D and D/A special function module of PLC, and the spindle drive control system of high-speed precision roll grinding head was designed based on FX3UPLC and frequency converter. The requirement of high-speed precision roll grinding head on its electrical control system was described, and the variable frequency speed-adjusting control system was introduced with the constitution, controlling scheme and signal-disposal methods. The hardware circuit, motor speed control trapezoid chart and analog control system communication program were designed. In addition, by using Kingview software, the PC monitor screen was developed, and the motor speed was set up by the input box of PC software, and the analog encoder was taken as the feedback sensor of output speed of the spindle motor. At the same time, the PID speed closed-loop control system was added to make spindle motor operate smoothly by the given speed. The PLC was adopted to carry on the on-site collection to the analog signal through the mathematical model calculation and signal feedback of the operating environment. Finally, the entire control system realized the on-line adjustment of the spindle motor output speed and the real-time detection of the process variables and ran steadily, which had good anti-interference performance and ensured the continuous and reliable, safe and efficient operation of the high-speed precision roll grinding head.
Key words: high-speed roll grinder    frequency converter    PLC    on-line monitoring
收稿日期: 2017-01-12 出版日期: 2018-06-28
CLC:  TM34  
基金资助:

国家自然科学基金资助项目（51465008）；贵州省高层次创新型人才培养计划项目（黔科合平台人才[2016]5659）
通讯作者: 吴怀超(1975-),男,湖北黄冈人,教授,博士生导师,博士,从事高速磨削及其装备研究,E-mail:magoubs@sina.com,http://orcid.org/0000-0002-1393-2662     E-mail: magoubs@sina.com
作者简介: 殷松(1992-),男,贵州遵义人,硕士生,从事机床电气控制研究,E-mail:luckgune@163.com
服务　　
把本文推荐给朋友
加入引用管理器
E-mail Alert
RSS
作者相关文章　　

引用本文:

殷松, 吴怀超, 杨绿, 晏文孟, 沈瑞芳. 高速精密轧辊磨头主轴驱动控制系统设计[J]. 工程设计学报, 2018, 25(3): 346-352,366.

YIN Song, WU Huai-chao, YANG Lü, YAN Wen-meng, SHEN Rui-fang. Design of spindle drive control system of high-speed precision roll grinding head. Chinese Journal of Engineering Design, 2018, 25(3): 346-352,366.

链接本文:

https://www.zjujournals.com/gcsjxb/CN/10.3785/j.issn.1006-754X.2018.03.014    或    https://www.zjujournals.com/gcsjxb/CN/Y2018/V25/I3/346

[1] 刘昆鹏.轧辊磨床磨头主轴系统若干关键问题研究[D].兰州:兰州理工大学机电工程学院,2010:1-5. LIU Kun-peng. Research on some key issues of spindle system in grinding head of roller grinding machine[D]. Lanzhou:Lanzhou University of Technology, College of Mechanical and Electrical Engineering, 2010:1-5.
[2] 张洪波,石俊强,陈奕,等.超高速磨削加工及其关键技术[J].机械工程师,2009(6):96-97. ZHANG Hong-bo, SHI Jun-qiang, CHEN Yi, et al. Ultrahigh speed grinding machining and its key technologies[J]. Mechanical Engineer, 2009(6):96-97.
[3] 徐展.WS1260磨床电气控制系统设计与实现[D].大连:大连理工大学软件学院,2014:1-2. XU Zhan. Design and implementation of electrical control system for WS1260 roller grinder[D]. Dalian:Dalian University of Technology, School of Software Technology, 2014:1-2.
[4] POPOV A P. Design of automatic control systems for machine tools[J]. Russian Engineering Research, 2014, 34(4):243-245.
[5] KHALID Nasir. Efficient energy management:is variable frequency drives the solution[J]. Procedia-Social and Behavioral Sciences, 2014, 145:371-376.
[6] 李炜.基于FXINPLC控制的轧辊磨床电气控制系统设计[J].天津冶金,2013(2):35-37. LI Wei. Design of electrical control system of roll grinder based on FXINPLC control[J]. Tianjin Metallurgy, 2013(2):35-37.
[7] 匡岳林.数控机床的电气控制系统设计[D].广州:华南理工大学自动化科学与工程学院,2011:2-5. KUANG Yue-lin. The design of electrical control system of numerical control machine[D]. Guangzhou:South China University of Technology, School of Automation Science and Engineering, 2011:2-5.
[8] LEGAEV V P, GENERALOV L K. Control system for a machine-tool drive with compensation of spindle eccentricity[J]. Russian Engineering Research, 2012, 32(5/6):430-432.
[9] 邓新锦.高速异步电机控制系统的研究[D].广州:广东工业大学自动化学院,2014:2-15. DENG Xin-jin. The research of high speed asynchronous spindle motor control system[D]. Guangzhou:Guangdong University of Technology, School of Automation, 2014:2-15.
[10] TANGJITSITCHAROEN S, TANGPORNPRASERT P, VIRULSRI Ch, et al. In-process monitoring and control of microassembly by utilising force sensor[J]. Journal of Achievements in Materials and Manufacturing Engineering, 2008, 31(2):588.
[11] 寇志伟,崔啸鸣,徐明娜,等.基于PLC与触摸屏的变频调速测控系统[J].电机与控制应用,2014,41(12):57-60. KOU Zhi-wei,CUI Xiao-ming, XU Ming-na, et al. Frequency control of motor speed control system based on PLC and HMI[J]. Electric Machines & Control Application, 2014, 41(12):57-60.
[12] 陈元勇.PLC控制电机变频调速试验系统的设计与实现[D].济南:山东大学信息科学与工程学院,2008:30-47. CHEN Yuan-yong. Design and implementation of PLC control electrical motor frequency conversion timing experiment system[D]. Jinan:Shandong University, School of Information Science and Engineering, 2008:30-47.
[13] 王建伟,杨风,张鹏,等.基于PLC与组态软件的电动机变频调速系统[J].电气技术,2009(12):65-67. WANG Jian-wei, YANG Feng, ZHANG Peng, et al. Electrical machinery frequency conversion and speed modulation system based on PLC and configuration software[J]. Electrical Technology, 2009(12):65-67.
[14] 王绎维.调速系统中变频器的EMI滤波器设计[D].苏州:苏州大学电子信息学院,2015:2-12. WANG Yi-wei. EMI filter designing of converter of adjustable speed electrical power drive systems[D]. Suzhou:Soochow University, School of Electronic and Information Engineering, 2015:2-12.
[15] 李燕,廖义奎,王永,等.图解变频器应用[M].北京:中国电力出版社,2014:61-74. LI Yan, LIAO Yi-kui, WANG Yong, et al. Illustration of inverter applications[M]. Beijing:China Electric Power Press, 2014:61-74.
[16] 李金城.PLC模拟量与通信控制应用实践[M].北京:电子工业出版社,2011:120-122. LI Jin-cheng. Practical application of PLC analog and communication control system[M]. Beijing:Electronic Industry Press, 2011:120-122.
[17] 李江全,蒙贺伟.三菱FX系列PLC数据通信及测控应用[M].北京:电子工业出版社,2011:244-255. LI Jiang-quan, MENG He-wei. Mitsubishi FX series PLC data communication and measurement and control application[M]. Beijing:Electronic Industry Press, 2011:244-255.
[18] ALTINTAS Y, ASLAN D. Integration of virtual and on-line machining process control and monitoring[J]. CIRP Annals-Manufacturing Technology, 2017, 66(1):349-352.
[1] 王春霖,刘畅,杨华,覃鸿,陈国柱. 用于油气勘探的电代油驱动装置系统设计与分析[J]. 工程设计学报, 2022, 29(2): 220-230.
[2] 张砀砀, 胡剑虹, 柯海森, 梁明轩. 基于颜色识别的轴承端面检测及整理装置设计[J]. 工程设计学报, 2021, 28(4): 489-494.
[3] 王超, 孙文旭, 马晓静, 陈纪旸, 栾义忠, 马思乐. 基于模糊控制的HVPE生长设备温度控制系统[J]. 工程设计学报, 2020, 27(6): 765-770.
[4] 张操, 华亮, 季霆, 周雨松, 董梁, 李鹏飞. 三明治自动制作与售卖系统研制[J]. 工程设计学报, 2018, 25(3): 353-359.
[5] 陈孟元. 土壤界限含水率自动检测系统设计研究[J]. 工程设计学报, 2017, 24(4): 473-479.
[6] 郑天池, 邵建新, 郭琳娜, 孙小刚, 张军, 邱自学. 铝电解电容器芯包引脚刺孔机控制系统设计[J]. 工程设计学报, 2016, 23(4): 378-384.
[7] 周芝峰, 周理, 王吉林. 基于PLC的校园照明智能控制系统设计[J]. 工程设计学报, 2010, 17(4): 307-311.
[8] 林峰, 刘杨, 许焰. 基于PLC的水听器回转扫描控制系统的设计及实现[J]. 工程设计学报, 2009, 16(1): 54-57.
[9] 高东强, 田振亚, 郝大建, 姚素芬. 陶瓷零件快速成型机铺料机构控制系统的研究[J]. 工程设计学报, 2008, 15(3): 229-232.
[10] 王 莉, 周新东. 基于Siemens PLC和自校正控制算法的炭素回转窑系统的控制[J]. 工程设计学报, 2008, 15(1): 50-53.
[11] 徐宁，陆源，葛锁良，赵涛. 基于PROFIBUS-DP和MPI的PLC腈纶生产控制系统[J]. 工程设计学报, 2007, 14(3): 235-238.