基于DSP的紫外/红外复合告警系统的伺服设计

工程设计学报

2009, Vol. 16

Issue (1): 7-11

工程设计理论、方法与技术

基于DSP的紫外/红外复合告警系统的伺服设计

陈兆兵^1,2, 郭劲¹, 姜伟伟^1,2

1.中国科学院长春光学精密机械与物理研究所，吉林长春 130033； 2. 中国科学院研究生院，北京 130039

Servo design of UV/IR complex warning system based on DSP

CHEN Zhao-Bing^1,2, GUO Jin¹, JIANG Wei-Wei^1,2

1.Changchun Institute of Optics， Fine Mechanics and Physics， Chinese Academy of Sciences， Changchun 130033， China；
2.Graduate School of the Chinese Academy of Sciences, Beijing 100039， China

全文: PDF(1220 KB) HTML

摘要： 紫外告警虚警率和精度都较低，而红外告警则相反．基于此，提出一种将紫外告警与红外跟踪相结合的全新的告警/跟踪一体模式，并进行基于TMS320F2812的伺服系统设计．依据设计要求和实际机械结构参数建立了伺服控制模型，并对模型进行软硬件设计．最后对伺服系统进行基于Matlab软件的伺服控制仿真，并在仿真环境试验型样机上进行相关的实验验证，得到与设计要求基本符合的结果，为系统的实际装校提供了依据．通过对仿真结果的分析处理，得到了系统可行性结论．该控制系统可应用于其他光电伺服平台．

关键词： 复合告警; DSP; 伺服设计; Matlab仿真

Abstract: The false alarm rate and detection precision of ultraviolet (UV) warning are low while those of infrared (IR) warning are opposite. Therefore a new kind of UV and IR composite alarm warning system was put forward. A servo system based on TMS320F2812 was designed and then the servo-control model based on design requirements and the mechanism fabric parameters was established. Moreover， the soft and hardware of this model were developed. Finally， the servo-control simulation of this servo system based on Matlab as well as experimental demonstration of this model in the simulating environment was conducted. The simulating result accorded with the design requirements， which provided reference for further real installation of the system. Through the analysis on the simulation results， it can be concluded that this system is feasible and this control system can also be applied to other photoelectricity servocontrol equipments．

Key words: complex warning DSP servo design Matlab simulation

出版日期: 2009-02-28

基金资助:

国防武器装备预研项目

	服务
	把本文推荐给朋友
	加入引用管理器
	E-mail Alert
	RSS
	作者相关文章
	陈兆兵
	郭劲
	姜伟伟

引用本文:

陈兆兵, 郭劲, 姜伟伟. 基于DSP的紫外/红外复合告警系统的伺服设计[J]. 工程设计学报, 2009, 16(1): 7-11.

CHEN Zhao-Bing, GUO Jin, JIANG Wei-Wei. Servo design of UV/IR complex warning system based on DSP[J]. Chinese Journal of Engineering Design, 2009, 16(1): 7-11.

链接本文:

https://www.zjujournals.com/gcsjxb/CN/ 或 https://www.zjujournals.com/gcsjxb/CN/Y2009/V16/I1/7

[1]	王超, 孙文旭, 马晓静, 陈纪旸, 栾义忠, 马思乐. 基于模糊控制的HVPE生长设备温度控制系统[J]. 工程设计学报, 2020, 27(6): 765-770.
[2]	王爱国, 陈健伟. 基于MATLAB的3-RPS并联机构控制系统仿真[J]. 工程设计学报, 2016, 23(2): 172-180.
[3]	刘林, 唐猛. 基于模型设计方法的混合磁悬浮平台的控制设计及实现[J]. 工程设计学报, 2012, 19(6): 428-433.
[4]	陈松, 宋晓琳. 基于DSP的智能小车路径跟随系统设计[J]. 工程设计学报, 2012, 19(4): 312-317.
[5]	虞晓琼, 张桦. 生物芯片扫描分析系统DSP软件设计[J]. 工程设计学报, 2004, 11(2): 89-92.
[6]	姜伟, 胡新华. 伺服螺旋机构建模与参数优化设计[J]. 工程设计学报, 2002, 9(3): 155-158.

Viewed

Full text

Abstract

Cited

Shared

Discussed