|
|
Anti-tension technology of slipway in long-stroke horizontal vibration table |
HE Wen1, ZHENG Jian-yi1,3, YU Mei2, SHEN Run-jie1,4, JIA Shu-shi1 |
1. The State Key Laboratory of Fluid Power Transmission and Control,Zhejiang Province Key Laboratory of Advanced Manufacturing Technology, Zhejiang University, Hangzhou 310027, China; 2. National Institute of Metrology, Beijing 100013, China; 3. Department of Mechanical and Electrical Engineering, Xiamen University, Xiamen 361005, China; 4. School of Electronics and Information, Tongji University, Shanghai 201804, China |
|
|
Abstract In order to solve the problem of output waveform distortion due to the pipes and wires' tension in a long-stroke horizontal vibration table, a follow-up-gear design technology was put forward which drove the pipes and wires to move synchronously with the slipway. The electromechanical coupling kinetic model of a horizontal vibration table was analyzed considering the tension of pipes and wires in it, and the influences of tension forces of the pipes and wires on the output waveform distortion of the horizontal vibration table was calculated. A follow-up gear for the slipway was developed based on a precise linear encoder, and drove a following table moving synchronously with the slipway. And the pipes and wires on the slipway were led out through the following table, on which the tension forces directly acted, but the tension force on the slipway drove to zero. The experimental results indicate that the output waveform distortion improves greatly after adding the follow-up gear when the horizontal vibration table works in long-stroke and ultra-low-frequency motion.
|
Published: 08 December 2011
|
|
长行程水平向振动台的滑台防牵拉技术
为了解决长行程水平向振动台中管线对滑台牵拉引起的输出波形失真问题,提出一种带动管线跟踪滑台同步运动的随动装置设计方法.建立管线牵拉力作用下的水平向振动台机电耦合动力学模型,计算管线牵拉力对振动台输出波形失真度的影响;设计一种基于光栅尺的滑台随动装置,带动随动平台与滑台做同步运动,滑台上的管线经随动平台后引出,此时管线的牵拉力直接作用在随动平台上,而滑台上受到的牵拉力趋于零.试验结果表明,通过增设滑台随动装置,水平向振动台在做超低频大行程振动时的输出波形失真度得到极大的改善.
|
|
[1] JJG 1342003.磁电式速度传感器检定规程[S].北京:中国计量出版社,2004. JJG 1342003.Verification regulation of electromagnetic velocity transducer [S].Beijing:China Metrology Publishing House,2004. [2] JJG 2332008.压电加速度计检定规程[S].北京:中国计量出版社,2009. JJG 2332008. Verification regulation for piezoelectric accelerometer [S].Beijing:China Metrology Publishing House,2008. [3] ISO 16063111999.Methods for the calibration of vibration and shock transducers Part 11:Primary vibration calibration by laser interferometry [S].Switzerland:International Organization for Standardization,1999. [4] JJG 2982005.中频标准振动台(比较法)检定规程[S].北京:中国计量出版社,2005. JJG 2982005.Verification regulation of standard vibrator in middle frequency band (comparison method) [S].Beijing:China Metrology Publishing House,2005. [5] OHM W S,WU Lixue,HANES P,et al.Generation of lowfrequency vibration using a cantilever beam for calibration of accelerometers [J].Journal of Sound and Vibration,2006,289(1/2):192-209. [6] GEORGE F L.Electrodynamic shaker fundamentals [J].Sound and Vibration,1997,31(4):14-23. [7] 韩冬.地震计校准用超低频标准振动系统关键技术的研究[D].杭州:浙江大学,2007. HAN Dong.Study on key techniques of ultralow frequency standard vibration system for seismometer calibration [D].Hangzhou:Zhejiang University,2007. [8] (美)绪方胜彦.系统动力学[M].北京:机械工业出版社,1983:21,117. [9] HE W,ZHU C P,MA F.Realization of lowdistortion ultralow frequency Vibration based on feedback control technology [C]∥ 2005 IEEE Networking,Sensing and Control Proceeding.California:IEEE,2005:795-798. [10] 沈润杰,何闻.大型宽频带水下振动台流固耦合动力学特性的研究[J].浙江大学学报:工学版,2006,40(4):724-728. Shen Runjie,HE Wen.Study on fluidsolid coupling dynamic characteristics of large widefrequencyrange underwater vibration tables [J].Journal of Zhejiang University∶Engineering Science,2006,40(4):724-728. [11] 张逸波,齐晓军,张丽新.200 kN振动台动圈建模与仿真分析 [J].航天器环境工程,2009,26(3):244-247. Zhang Yibo,Qi Xiaojun,Zhang Lixin.Modeling of armature of 200 kN shaker and its simulation [J].Spacecraft Environment Engineering,2009,26(3):244-247. |
|
Viewed |
|
|
|
Full text
|
|
|
|
|
Abstract
|
|
|
|
|
Cited |
|
|
|
|
|
Shared |
|
|
|
|
|
Discussed |
|
|
|
|