Please wait a minute...
浙江大学学报(工学版)
浙江大学学报(工学版)
能源与机械工程     
吸入室角度对环形射流泵空化性能的影响
肖龙洲1,2,龙新平1,2
1.武汉大学 动力与机械学院,湖北 武汉 430072; 2.水射流理论与新技术湖北省重点实验室,湖北 武汉 430000
Influence of inclined angle on cavitation performance of annular jet pump
XIAO Long-zhou1,2, LONG Xin-ping1,2
1. School of Power and Mechanical Engineering, Wuhan University, Wuhan 430072, China; 2.Key Laboratory of Jet Theory and New Technology of Hubei Province, Wuhan 430000, China
 全文: PDF(1490 KB)   HTML
摘要：

利用数值模拟的方法研究环形射流泵(AJP)内的空化发展规律,比较分析不同吸入室角度对环形射流泵空化性能的影响,得到如下结论.1）Realizable k-ε湍流模型结合mixture多相流模型及Schnerr-Sauer空化模型可以较好地模拟环形射流泵内的空化现象.2）随着环形射流泵出口压力的降低,喉管入口壁面处的空化区域会向喉管内延伸,引发的低压区会不断地向轴心线扩展.当低压区扩展到轴心线时,喉管内空化区剧烈发展,环形射流泵进入极限工况.3）当空化数大于极限空化数时,环形射流泵效率不受空化的影响；当空化数降低至极限空化数时,环形射流泵的效率陡降,空化数保持恒定不再降低,对应的值是极限空化数.4）吸入室角度越小,各个流量比对应的极限空化数越小,泵的空化性能越好.较小的吸入室角度使得环形射流泵更易诱发回流中心及剪切层空化云的产生.
Abstract:

The numerical method was conducted to analyze the development of the cavitation in annular jet pump (AJP), and the impacts of different inclined angle  on the cavitation performance of AJP were comparatively analyzed. The following results were obtained. 1) Combined with mixture model and Schnerr-Sauer model, realizable k-ε model can reasonably simulate the cavitation phenomenon in AJP. 2) With the decreasing outlet pressure of the AJP, the cavitation area at the inner wall of the throat inlet will stretch alone the throat and the induced low pressure will extend to the axis. When the low pressure attaches to the axis, the cavitation in the throat boosts and the pump turns out to be under operating limits. 3) When cavitation number is larger than limited cavitation number, the efficiency of AJP varies little regardless of the developing cavitation.  When cavitation number drops to the limited cavitation number, the performance of AJP suffers a great decrease, while the cavitation number will stay constant and the corresponding value is the limited cavitation number. 4) The smaller the inclined angle is, the smaller the corresponding limited cavitation number is and the better cavitation performance of AJP is. The cavitation cloud is easier to be induced at the center of the recirculation and the shearing layer with a smaller inclined angle．
出版日期: 2018-06-06
:  TB 752  
基金资助:

国家自然科学基金资助项目(51179134)
通讯作者: 龙新平，男，教授，博导     E-mail: xplong@whu.edu.cn
作者简介: 肖龙洲（1988－), 男, 博士生, 从事空化流动及数值模拟的研究. E-mail: longzhou@whu.edu.cn
服务　　
把本文推荐给朋友
加入引用管理器
E-mail Alert
RSS
作者相关文章　　

引用本文:

肖龙洲,龙新平. 吸入室角度对环形射流泵空化性能的影响[J]. 浙江大学学报(工学版), 10.3785/j.issn.1008-973X.2015.01.018.

XIAO Long-zhou, LONG Xin-ping. Influence of inclined angle on cavitation performance of annular jet pump. JOURNAL OF ZHEJIANG UNIVERSITY (ENGINEERING SCIENCE), 10.3785/j.issn.1008-973X.2015.01.018.

链接本文:

http://www.zjujournals.com/eng/CN/10.3785/j.issn.1008-973X.2015.01.018    或    http://www.zjujournals.com/eng/CN/Y2015/V49/I1/123

［1］ LU H, SHANG H. Mechanism and calculation theory of jet pump cavitation ［J］. Scientia Sinica Series A, 1987, 30(11): 1174-1187．
［2］ 龙新平,关运生,王丰景,等. 补气位置对改善射流泵空化性能的试验［J］. 江苏大学学报:自然科学版,2009, 30(3): 270-273．
LONG Xin-ping, GUAN Yun-sheng, WANG Feng-jing, et al. Experiment on air supplying position for improvement of jet pump cavitation performance ［J］. Journal of Jiangsu University: Natural Science Edition, 2009, 30(3): 270-273．
［3］ 龙新平,何培杰. 射流泵汽蚀问题研究综述［J］. 水泵技术, 2003(4): 33-38．
LONG Xin-ping, HE Pei-jie. A review of jet pump cavitation ［J］. Journal of Pump Technology, 2003(4): 33-38．
［4］ WIESCHE S. Numerical simulation of cavitation effects behind obstacles and in an automotive fuel jet pump ［J］. Journal of Heat Mass Transfer, 2005, 41(7): 615-624．
［5］ LONG X, YAO H, ZHAO J. Investigation on mechanism of critical cavitating flow in liquid jet pumps under operating limits ［J］. International Journal of Heat and Mass Transfer, 2009, 52(9): 2415-2420．
［6］ KUDIRKA A A, DECOSTER M A. Jet pump cavitation with ambient and high temperature water ［J］. ASME Journal of Fluids Engineering, 1979, 101(1): 93-99．
［7］ BONNINGTON S T. Jet pumps and ejectors: a state of the art reviews and bibliographer ［M］. Cranfield, Bedford, UK: BHRA Fluid Engineering, 1972．
［8］ CUNNINGHAM R G, HANSEN A G, NA T Y. Jet pump cavitation ［J］. ASME: Journal of Basic Engineering, 1970, 92(3): 483-494．
［9］ SHIMIZU Y, NAKAMUEA S, KAZUHARA S, et al. Studies of the configuration and performance of annular type jet pumps ［J］. ASME Journal of fluids Engineering, 1987, 109(3): 205-212．
［10］ 刘晖霞. 环形射流泵产生空化的机理及其改善的研究［D］. 重庆: 重庆大学, 2007．
LIU Hui-xia. Study of cavitation mechanism and its improvement for the annular jet pump ［D］. Chongqing: Chongqing University, 2007．
［11］ 龙新平,程茜,韩宁,等. 射流泵空化流动的数值模拟［J］. 排灌机械工程学报, 2010, 28(1): 7-11．
LONG Xin-ping, CHENG Qian, HAN Ning, et al. Numerical simulation on cavitating flow within jet pump ［J］. Journal of Drainage and Irrigation Machinery Engineering, 2010, 28(1): 7-11．
［12］ XIAO L, LONG X, LI X, et al. Numerical investigation on the recirculation in annular jet pumps ［J］. Journal of Mechanical Science and Technology, 2013, 27(6): 16031609．
［13］ 蔡标华. 射流泵初生空化及其试验研究［D］. 武汉：武汉大学,2005．
CAI Biao-hua. Analysis and experimental study on incipient cavitation within jet pumps ［D］. Wuhan: Wuhan University, 2005．
［14］ FRANC J P, MICHEL J M. Fundamentals of cavitation ［M］. Netherlands: Springer, 2005．
No related articles found!