Please wait a minute...
J4  2011, Vol. 45 Issue (2): 197-200    DOI: 10.3785/j.issn.1008-973X.2011.02.001
机械工程     
基于代理模型的注射参数迭代优化方法
赵朋1, 傅建中1, 李阳2, 崔树标2
1.浙江大学 流体传动及控制国家重点实验室,浙江 杭州 310027;
2.华中科技大学 材料成形与模具技术国家重点实验室,湖北 武汉 430074
Iterative optimization method for injection parameters based on
surrogate model
ZHAO Peng1, FU Jian-zhong1, LI Yang2, CUI Shu-biao2
1. State Key Laboratory of Fluid Power Transmission and Control, Zhejiang University, Hangzhou 310027, China;
2. State Key Laboratory of Material Processing and Die & Mould Technology, Huazhong University of
Science and Technology, Wuhan 430074, China.
 全文: PDF  HTML
摘要:

型腔压力和熔体温差是反映塑料制品质量好坏的2项重要质量指标.考虑到塑料制品的薄壁特性,从黏性流体力学的基本方程出发,建立一种简化流动模型作为代理模型代替耗时的塑料注射成型模拟软件快速预测上述质量指标,基于代理模型的预测结果,采用粒子群算法实现注射参数的迭代优化,该方法计算速度快效率高,对知识的依赖程度低.最后通过实验对代理模型的正确性和优化方法的有效性进行验证,实验结果表明,基于代理模型的型腔压力预测值与实验值吻合较好,相对误差值只有8.41%,提出的优化方法与响应面方法的优化结果基本一致,但运行时间仅为响应面方法的0.02%.

Abstract:

Cavity pressure and temperature difference are two important quality criteria. Considering that most injection molded parts have a sheet like geometry, a fast strip analysis model based on mechanics equations for viscous fluid, was adopted as a surrogate model to approximate the time-consuming computer simulation software for predicating the above quality criteria. According to the predicted quality criteria, a particle swarm optimization algorithm was employed to find out the optimum injection parameters. The proposed optimization method can optimize the injection parameters in short time and it does not rely on any knowledge of molding process. Finally, two experiments were employed to validate the surrogate model and the proposed optimization method. Experimental results show that the cavity pressure predicted by the surrogate model agree well with the experimental data, with the relative error being less than 8.41%, and the results of the proposed optimization method are nearly identical to that of response surface method, while the required time of the proposed method is only 0.02% of that of response surface method.

出版日期: 2011-03-17
:  TQ 320  
基金资助:

国家自然科学基金资助项目(50875095,50905162);材料成形与模具技术国家重点实验室开放基金资助项目(2010-P01).

通讯作者: 傅建中,男,教授,博导.     E-mail: fjz@zju.edu.cn
作者简介: 赵朋(1983—),男,湖北英山人,博士后,从事塑料注射成型工艺及设备的研究.E-mail:pengzhao@zju.edu.cn
服务  
把本文推荐给朋友
加入引用管理器
E-mail Alert
RSS
作者相关文章  

引用本文:

赵朋, 傅建中, 李阳, 崔树标. 基于代理模型的注射参数迭代优化方法[J]. J4, 2011, 45(2): 197-200.

ZHAO Peng, FU Jian-zhong, LI Yang, CUI Shu-biao. Iterative optimization method for injection parameters based on
surrogate model. J4, 2011, 45(2): 197-200.

链接本文:

http://www.zjujournals.com/eng/CN/10.3785/j.issn.1008-973X.2011.02.001        http://www.zjujournals.com/eng/CN/Y2011/V45/I2/197

[1] 陈曦.基于质量的注塑过程建模方法研究[D].杭州:浙江大学,2001: 33.
CHEN Xi. Research on modeling of injection molding based on part quality [D]. Hangzhou: Zhejiang University, 2001: 33.
[2] TURNG L S, PEIC M. Computer aided process and design optimization for injection moulding [J]. Proceedings of the Institution of Mechanical Engineers, Part B: Journal of Engineering Manufacture, 2002, 216(12): 1523-1532.

[3] SHEN C Y, WANG L X, LI Q. Optimization of injection molding process parameters using combination of artificial neural network and genetic algorithm method[J]. Journal of Materials Processing Technology, 2007, 183(2/3): 412-418.
[4] ZHOU J, TURNG L S, KRAMSCHUSTER A. Single and multi objective optimization for injection molding using numerical simulation with surrogate models and genetic algorithms [J]. International Polymer Processing, 2008, 21(5): 509-520.
[5] GAO Y H, WANG X C. Surrogatebased process optimization for reducing warpage in injection molding [J]. Journal of Materials Processing Technology, 2009, 209(3): 1302-1309.
[6] PANDELIDIS I, ZOU Q. Optimization of injection molding design part II: molding conditions optimization [J]. Polymer Engineering and Science, 1990, 30(15): 883-892.
[7] KUMAR A, GHOSHDATIDAR P S, MUJU M K. Computer simulation of transport processes during injection moldfilling and optimization of the molding conditions [J]. Journal of Materials Processing Technology, 2002, 120(1/3): 438-449.
[8] LAM Y C, BRITTON G A, DENG Y M. A computeraided system for an optimal moulding conditions design using a simulationbased approach [J]. International Journal of Advanced Manufacturing Technology, 2003, 22(7/8): 574-586.
[9] ZHOU H M, LI D Q. Integrated simulation of the injection molding process with stereolithography molds[J]. International Journal of Advanced Manufacturing Technology, 2006, 28(1/2): 53-60.
[10] 赵朋,周华民,严波,等.塑料注射成型中注射压力和熔体温度的快速预测[J].中国塑料,2007, 21(9): 53-56.
ZHAO Peng, ZHOU Huamin, YAN Bo, et al. Fast prediction of the injection pressure and melt temperature during injection molding [J]. China Plastics, 2007, 21(9): 53-56.
[11] 贺益君,陈德钊.适于混合整数非线性规划的混合粒子群优化算法[J].浙江大学学报:工学版,2008,42(5): 747-751.
HE Yijun, CHEN Dezhao. Hybrid particle swarm optimization algorithm for mixedinteger nonlinear programming [J]. Journal of Zhejiang University: Engineering Science, 2008, 42(5): 747-751.

No related articles found!