Please wait a minute...
浙江大学学报(工学版)
J4  2013, Vol. 47 Issue (3): 540-548    DOI: 10.3785/j.issn.1008-973X.2013.03.021
化学工程     
环氧乙烷氢甲酯化法生产1,3丙二醇过程放大与技术经济分析
曾宏1,3 ,朱毓3,方柏山1,2
1. 华侨大学 化工学院,福建 厦门 361021；2. 厦门大学 化学化工学院,福建 厦门 361005；
3. 泉州师范学院 化学与生命科学学院,福建 泉州 362000
Process scaleup and techno-economic analysis on hydroesterification of
ethylene oxide technology for 1,3-propanediol production
ZENG Hong 1, 3,ZHU Yu 3,FANG Bai-shan 1, 2
1. College of Chemical Engineering, Huaqiao University, Xiamen 361021, China;
2. College of Chemistry and Chemical Engineering, Xiamen University, Xiamen 361005, China;
3. College of Chemistry and Life Sciences, Quanzhou Normal University, Quanzhou 362000, China
 全文: PDF 
摘要：

设计环氧乙烷（EO）氢甲酯化法生产1,3丙二醇（PDO）的新工艺,耦合闪蒸并实现过程综合.基于小试结果放大,应用SuperPro Designer仿真软件,模拟年产万吨PDO的全工艺流程.对比2种不同氢甲酯化压力的工艺方案(A方案：7 MPa);B方案：4 MPa,并进行经济成本分析.模拟结果表明：主要过程数据符合实验结果,工艺设计合理|经济分析显示：高温高压设备占设备购置成本比例较大,原料成本占操作成本88%以上|方案A和方案B的项目总投资分别约10 877万元和10 004万元,税后净利润约2 800万元/a和2 743万元/a,投资收益率分别为29.58%和31.15%．
关键词： 1;  3-丙二醇;  环氧乙烷;  3-羟基丙酸甲酯;  氢甲酯化;  过程模拟;  经济分析    
Abstract:

A new technology of hydroesterification of ethylene oxide (EO) for 1,3-propanediol (PDO) production was designed. Flash procedures were coupled and the process was synthesized. Based on scale-up of laboratory experiments, the SuperPro Designer emluator was applied to simulate the whole process of EO hydroesterification technology for annual 10 000 tons PDO production. Two hydroesterification pressure scenarios (A for 7 MPa and B for 4 MPa) were compared, coupling with costing and economic evaluation on the flowsheeting. Simulation  indicates that the process design is reasonable with main process data agreeing with experimental results. The economic analyses show that high temperature and high pressure equipments share large proportion of equipment purchase cost, and the raw material costs are more than 88% of operating cost. The expected returns on investment of scenario A and B reach 29.58% and 31.15% as the after-tax profits are about 28.00 and 27.43 million yuan annually, with the project total investments of approximately 108.77 and 100.04 million yuan．
Key words: PDO    EO    methyl 3-hydroxypropionate    hydroesterification    process simulation    economic analysis
出版日期: 2013-04-10
:  TQ 018  
基金资助:

国家“863”高技术研究发展计划资助项目（2006AA020103）;福建省高校产学合作科技重大资助项目（2010H6023）;泉州市技术研究与开发基金资助项目（2010G6）.
通讯作者: 方柏山，男，教授，博导．E-mail：fbs@xmu.edu.cn   
作者简介: 曾宏（1977-），男，副教授，从事过程系统综合的研究.E-mail：hongzeng@126.com
服务　　
把本文推荐给朋友
加入引用管理器
E-mail Alert
RSS
作者相关文章　　

引用本文:

曾宏, 朱毓, 方柏山. 环氧乙烷氢甲酯化法生产1,3丙二醇过程放大与技术经济分析[J]. J4, 2013, 47(3): 540-548.

ZENG Hong, ZHU Yu, FANG Bai-shan. Process scaleup and techno-economic analysis on hydroesterification of
ethylene oxide technology for 1,3-propanediol production. J4, 2013, 47(3): 540-548.

链接本文:

http://www.zjujournals.com/xueshu/eng/CN/10.3785/j.issn.1008-973X.2013.03.021    或    http://www.zjujournals.com/xueshu/eng/CN/Y2013/V47/I3/540

［1］ LAFFEND L A,NAGARAJAN V,NAKAMURA C E.Bioconversion of a fermentable carbon source to 1,3-propanediol by a single microorganism:US,5686276 ［P］.1997-11-11．
［2］ LAFFEND L A,NAGARAJAN V,NAKAMURA C E.Bioconversion of a fermentable carbon source to 1,3-propanediol by a single microorganism:US,6025184 ［P］.2000-02-15．
［3］ GNZEL B,YONSEL S,DECKWER W D.Fermentative production of 1,3-propanediol from glycerol by Clostridium butyricum up to a scale of 2 m3 ［J］.Applied Microbiology and Biotechnology,1991,36（3）：289-294．
［4］ BARBIRATO F,HIMMI E H,CONTE T,et al.1,3-propanediol production by fermentation: An interesting way to valorize glycerin from the ester and ethanol industries ［J］.Industrial Crops and Products,1998,7（2/3）：281-289．
［5］ BIEBL H,MENZEL K,ZENG A P,et al.Microbial production of 1,3-propanediol ［J］.Applied Microbiology and Biotechnology,1999,52（3）：289-297．
［6］ PAPANIKOLAOUA S,RUIZ-SANCHEZB P,PARISETB B,et al.High production of 1,3-propanediol from industrial glycerol by a newly isolated Clostridium butyricum strain ［J］.Journal of Biotechnology,2000,77（2/3）：191-208．
［7］ HARTLEP M,HUSSMANN W,PRAYITNO N,et al.Study of two-stage processes for the microbial production of 1,3-propanediol from glucose ［J］.Applied Microbiology and Biotechnology,2002,60（1/2）：60-66．
［8］ 张健,赵红英,刘宏娟,等.以葡萄糖为辅助底物发酵生产1,3-丙二醇的研究［J］.现代化工,2002,22（6）：3235．
ZHANG Jian,ZHAO Hong-ying,LIU Hong-juan,et al.Fermenting production of 1,3-propanediol by using glucose as cosubstrate ［J］.Modern Chemical Industry,2002,22（6）：32-35．
［9］ CHEN X,ZHANG D J,QI W T,et al.Microbial fed-batch production of 1,3-propanediol by Klebsiella pneumoniae under micro-aerobic conditions ［J］.Applied Microbiology and Biotechnology,2003,63（2）：143-146．
［10］ 陈宏文,王蔚,方柏山,等.克雷伯杆菌生产1,3-丙二醇关键酶发酵条件研究［J］.高校化学工程学报,2004,18（5）：621-627．
CHEN Hong-wen,WANG Wei,FANG Bai-shan,et al.Studies on fermentation conditions for key enzymes in 1,3-propanediol production with Klebsiella pneumoniae［J］.Journal of Chemical Engineering of Chinese Universities,2004,18（5）：621-627．
［11］ ZHAO Y N,CHEN G,YAO S J.Microbial production of 1,3-propanediol from glycerol by encapsulated Klebsiella pneumoniae［J］.Biochemical Engineering Journal,2006,32（2）：93-99．
［12］ LIU H J,ZHANG D J,XU Y H,et al.Microbial production of 1,3-propanediol from glycerol by Klebsiella pneumoniae under micro-aerobic conditions up to a pilot scale ［J］.Biotechnology Letters,2007,29（8）：1281-1285．
［13］ ARNTZ D,WIEGAND N.Method of preparing 1,3-propanediol:US,5015789 ［P］.1991-05-14．
［14］ HAAS T,WIEGAND N,ARNTZ D.Process for the production of 1,3-propanediol:US,5334778 ［P］.1994-08-02．
［15］ ARNTZ D,HAAS T,SCHAFER-SINDLINGER A.Process for the preparation of 1 3 propanediol by the hydrogenatton of hydroxypropionaldehyde:US,5364984 ［P］.1994-11-15．
［16］ HAAS T,ARNTZ D.Process for the preparation of 1，3- propanediol:US,5364987 ［P］.1994-11-15．
［17］ UNRUH J D,RYAN D A,NICOLAU I.Method for the manufacture of 1,3-propanediol:US,RE34349 ［P］.1993-08-17．
［18］ LAWRENCE F R,SULLIVAN R H.Process for making a dioxane:US,3687981 ［P］.1972-08-29．
［19］ FORSCHNER T C,WEIDER P R,SLAUGH L H,et al.Process for preparing 1,3-propanediol from methyl 3-hydroxypropionate:US,6191321 ［P］.2001-02-20．
［20］ 李秉鲁,张银珠,李正浩,等.由3-羟基酯制备1,3-链烷二醇的方法：中国,CN1355160A ［P］.2002-06-26．
［21］ 李秉鲁,郑仁善,张银珠,等.由3-羟基酯制备1,3-烷二醇的方法：中国,CN1417186A ［P］.2003-05-14．
［22］ KIM H S,BAE J Y,LEE J S,et al.An efficient catalytic system for the carbomethoxylation of ethylene oxide ［J］.Applied Catalysis A: General,2006,301（1）：75-78．
［23］ 赵正康,曹勇,王路存,等.3-羟基丙酸甲酯加氢制1,3-丙二醇用的纳米铜基催化剂及其制备方法：中国,CN100503039C ［P］.2009-06-24．
［24］ 崔芳,陈静,夏春谷,等.由3-羟基丙酸甲酯制备1,3-丙二醇的方法：中国,CN101195558B ［P］.2010-10-06．
［25］ 应于舟,赵振康,杨菊群,等.环氧乙烷催化合成3-羟基丙酸甲酯的研究［J］.华东理工大学学报：自然科学版,2008,34（3）：334337．
YING Yu-zhou,ZHAO Zhen-kang,YANG Ju-qun,et al.Synthesis of methyl 3-hydroxypropanoate catalyzed by epoxy ethane ［J］.Journal of East China University of Science and Technology:Natural Science,2008,34（3）：334-337．
［26］ 冯看卡.3-羟基丙酸甲酯加氢制1,3-丙二醇的研究［D］.青岛：青岛科技大学,2008:70-76．
FENG Kan-ka.Study on the hydrogenation of methyl 3-hydroxypropionate to 1,3-propanediol ［D］.Qingdao:Qingdao University of Science & Technology,2008:70-76．
［27］ 吕志果,冯看卡,郭振美.3-羟基丙酸甲酯加氢制1,3-丙二醇的纳米铜基催化剂研究［J］.精细化工,2008,25（4）：362-365．
LV Zhi-guo,FENG Kan-ka,GUO Zhen-mei.Study of nanon copper-based catalysts for hydrogenation of methyl 3-hydroxypropionate to 1,3-propanediol ［J］.Fine Chemicals,2008,25（4）：362-365．
［28］ 吕志果,赵正康,郭振美,等.一种3-羟基丙酸酯加氢制备1,3-丙二醇的催化剂及其制备方法：中国,CN101176848B ［P］.2011-03-02．
［29］ GUO Z M,WANG H S,LV Z G,et al.Catalytic performance of ［Bmim］［Co(CO)4］ functional ionic liquids for preparation of 1,3-propanediol by coupling of hydroesterification-hydrogenation from ethylene oxide ［J］.Journal of Organometallic Chemistry,2011,696（23）：3668-3672．
［30］ 陈小平,王世琴,马玉刚,等.一种3-羟基丙酸甲酯加氢制备1,3-丙二醇的方法：中国,CN101993352A ［P］.2011-03-30．
［31］ 陈小平,周海军,马玉刚,等.一种3-羟基丙酸甲酯的合成方法：中国,CN102050736A ［P］.2011-05-11．
［32］ 陈小平,王世琴,马玉刚,等.一种用于3-羟基丙酸甲酯加氢制备1,3-丙二醇的催化剂：中国,CN102059125A ［P］.2011-05-18．
［33］ 刘春杰.环氧乙烷氢甲酯化合成3-羟基丙酸甲酯的研究［D］.太原：太原理工大学,2011:33-38．
LIU Chun-jie.Study on carbomethoxylation of ethylene oxide for preparing methyl 3-hydroxypropanoate ［D］.Taiyuan:Taiyuan University of Technology,2011:33-38．
［34］ 曾宏,李洪明,方柏山.生物柴油超临界甲醇法生产工艺全流程模拟与经济分析［J］.过程工程学报,2010,10（6）：1168-1173．
ZENG Hong, LI Hong-ming, FANG Bai-shan.Process simulation and economic analysis on supercritical methanol production technology of biodiesel ［J］.The Chinese Journal of Process Engineering,2010,10（6）：1168-1173．
[1] 阮胤, 邱展, 王福新. 周期激励下NACA 0012翼型单自由度失速颤振研究[J]. 浙江大学学报(工学版), 2017, 51(9): 1870-1880.
[2] 杨琴, 张海军, 沈剑英, 刘宇陆. 基于Boltzmann矩方程的扩展速度滑移边界条件[J]. 浙江大学学报(工学版), 2017, 51(12): 2408-2413.
[3] 李建, 刘猛, 段钰锋, 许超. 污泥掺混褐煤水热制固体燃料的理化特性[J]. 浙江大学学报(工学版), 2016, 50(2): 327-332.
[4] 王刚, 郑海峰, 尹红, 袁慎峰, 陈志荣. 1-氯-1,1-二氟乙烷裂解制备偏氟乙烯[J]. 浙江大学学报(工学版), 2015, 49(9): 1812-1816.
[5] 郑志浩, 汪国昭. 基于PH曲线插值的圆锥曲线逼近[J]. 浙江大学学报(工学版), 2015, 49(12): 2290-2297.
[6] 唐凯, 贾佳, 邓靖, 宋亚丽, 李青松. 超声及高锰酸钾-超声协同降解水中17β-雌二醇的影响因素分析[J]. 浙江大学学报(工学版), 2014, 48(6): 1132-1140.
[7] 郭小农, 杨商飞, 罗永峰, 邱丽秋, 郁政华, 郑祥杰. 大跨度屋盖钢结构拆撑过程恒力千斤顶卸载法[J]. 浙江大学学报(工学版), 2014, 48(10): 1809-1815.
[8] 李德骏,汪港,杨灿军,金波,陈燕虎. 基于NTP和IEEE1588海底观测网时间同步系统[J]. J4, 2014, 48(1): 1-7.
[9] 孔祥强,林琳,李瑛, 杨前明. R410A直膨式太阳能热泵热水器性能研究[J]. J4, 2013, 47(9): 1666-1671.
[10] 唐月, 朱明乔, 黄霖, 王萌, 陈新志. Au/TS-1催化剂上葡萄糖氧化[J]. J4, 2013, 47(6): 1114-1119.
[11] 张世珍,王维锐,李玉良,杨文伟,颜益. 一种新型材料淬火过程的数值模拟和实验研究[J]. J4, 2013, 47(3): 535-539.
[12] 王鹏, 林东强, 姚善泾. 离子液体复合溶剂法制备纤维素多孔微球[J]. J4, 2013, 47(12): 2160-2164.
[13] 石凯凯, 蔡力勋, 包陈, 姚瑶. 断裂韧性测试的量纲一载荷分离方法及应用[J]. J4, 2012, 46(7): 1201-1206.
[14] 丁立聪,金小军,王春晖,金仲和. ZDPS-1A卫星电源系统设计与在轨验证[J]. J4, 2012, 46(11): 2073-2080.
[15] 叶健,黄海波,张乐天,王靖岱,蒋斌波,阳永荣,廖祖维. 丁二醇活化氯化镁制备Ziegler-Natta
催化剂及其乙烯聚合[J]. J4, 2011, 45(5): 907-913.