Please wait a minute...
浙江大学学报(工学版)
J4  2013, Vol. 47 Issue (2): 209-215    DOI: 10.3785/j.issn.1008-973X.2013.02.003
机械工程     
飞机大部件调姿机构磨损预测模型的构建与仿真
应征, 章明, 王青, 柯映林
浙江大学 流体传动及控制国家重点实验室,浙江 杭州 310027
Modeling and simulation of wear for alignment mechanism of
large aircraft component
YING Zheng, ZHANG Ming, WANG Qing, KE Ying-lin
State Key Lab of Fluid Power Transmission and Control, Zhejiang University, Hangzhou 310027, China
 全文: PDF 
摘要：

针对飞机大部件调姿机构球铰磨损量预测问题,提出一种含间隙的球铰磨损模型.根据球铰的几何结构构建运动学模型；采用含迟滞阻尼系数的连续接触力模型与改进Coulomb摩擦力模型建立球铰的动力学模型；结合Archard方程建立球铰的磨损模型.为了能够获得接触表面的磨损分布情况,将磨损表面离散,借助Hertz接触理论计算接触力的分布,并以离散后的单张曲面为单元分别计算与保存单张曲面磨损量.针对一种四定位器的调姿机构,模拟调姿过程进行仿真计算,结果显示：单个球头表面磨损分布并不均衡,4个球头之间的磨损分布情况类似,但是磨损量存在一定的差异.该磨损模型能够用于调姿机构寿命的预测,并对调姿机构的机械设计提供参考.
关键词： 调姿机构;  球铰;  动力学建模;  磨损    
Abstract:

To predict the wear extent of spherical joints in alignment mechanism of large aircraft component, a wear model of spherical joint with clearance was proposed. The kinematic model of spherical joint was constructed according to its geometric condition. Continuous contact force model with hysteresis damping coefficient and Coulomb friction law with modification were utilized to develop the dynamic model of spherical joint. The Archard’s equation was employed to model the wear of spherical joint. To acquire the distribution of wear depth, the surface on the ball and socket was discretized for calculating and storing wear depth. Hertz contact theory was used to obtain the distribution of contact force. Process simulation of alignment mechanism with four positioners was carried out. From the result acquired, it shows that the distribution of wear on the surface is not uniform, and the total wear volumes of each spherical joint are not uniform either. This wear model is also able to be applicable for life prediction and mechanical design of alignment mechanism.
Key words: alignment mechanism    spherical joint    dynamic modeling    wear
出版日期: 2013-03-14
:  TH 122  
基金资助:

 国家自然科学基金资助项目 (50905161)；浙江省科技计划资助项目(2010C31097)；高等学校博士学科点专项科研基金资助项目(20090101120021).
通讯作者: 章明，男，工程师.     E-mail: zhgmg@126.com
作者简介: 应征(1983—)，男，博士生，从事飞机调姿系统仿真，虚拟样机研究工作.E-mail: yingzheng.cn@gmail.com
服务　　
把本文推荐给朋友
加入引用管理器
E-mail Alert
RSS
作者相关文章　　

引用本文:

应征, 章明, 王青, 柯映林. 飞机大部件调姿机构磨损预测模型的构建与仿真[J]. J4, 2013, 47(2): 209-215.

YING Zheng, ZHANG Ming, WANG Qing, KE Ying-lin. Modeling and simulation of wear for alignment mechanism of
large aircraft component. J4, 2013, 47(2): 209-215.

链接本文:

http://www.zjujournals.com/xueshu/eng/CN/10.3785/j.issn.1008-973X.2013.02.003    或    http://www.zjujournals.com/xueshu/eng/CN/Y2013/V47/I2/209

［1］ 郭志敏,蒋君侠,柯映林.一种精密三坐标POGO柱设计与精度研究［J］.浙江大学学报,工学版,2009,43(9): 1649-1654.
GUO Zhi-min, JIANG Jun-xia, KE Ying-lin. Design and accuracy for POGO stick with threeaxis ［J］. Journal of Zhejiang University: Engineering Science, 2009, 43(9): 1649-1654.
［2］ 邵荷生,曲敬信,许小棣,等.摩擦与磨损［M］.北京:煤炭工业出版社,1992.
［3］ 吴国清,张晓峰,方亮,等.两体磨料磨损的三维动态模拟［J］.摩擦学学报,2000,20(5): 360-364.
WU Guo-qing, ZHANG Xiao-feng, FANG Liang, et al. 3-D dynamic simulation of two-body abrasion ［J］. Tribology, 2000, 20(5): 360-364.
［4］ DUFRANE K F, KANNEL J W, MCCLOCKEY T H. Wear of steam turbine journal bearings at low operating speeds ［J］. Journal of Lubrication Technology, 1983,105: 313-317.
［5］ GERTZOS K P, NIKOLAKOPOULOS P G, CHASALEVRIS A C, et al. Wear identification in rotor-bearing systems by measurements of dynamic bearing characteristics ［J］. Computers and Structures, 2011, 89(1/2): 55-66.
［6］ FLORES P. Modeling and simulation of wear in revolute clearance joints in multibody systems ［J］. Mehcanism and Machine, 2009, 44(6): 1211-1222.
［7］ FIALHO J C, FERNADES P R, EA L, et al. Computational hip joints simulator for wear and heat generation ［J］. Journal of Biomechanics, 2007, 40(11): 2358-66.
［8］ HIRANI H, VERMA M. Tribological study of friction in worn misaligned journal bearings under severe hydrodynamic lubrication ［J］. Tribology International, 2009, 42(2): 378-390.
［9］ DUBOWSKY S, FREUDENSTEIN F. Dynamic analysis of mechanical systems with clearances, Part 1: Formation of dynamic model ［J］. Journal of Engineering for Industry, 1971, 93(1): 305-309.
［10］ HUNT K H, CROSSLEY F R E. Coefficient of restitution interpreted as damping in Vibroimpact ［J］. Journal of Applied Mechanics, 1975, 7(2): 440-445.
［11］ HERTZ H. On the contact of solids-On the contact of ridid elastic solids and on hardness (Translated by D. E. Jones and G.A.Schott) ［J］. Miscellaneous Papers, 1986: 146-183.
［12］ ROONEY G T, DERAVI P. Coulomb friction in mechanism sliding joints ［J］. Mechanism and Machine Theory, 1982, 17(3): 207-211.
［13］ ARCHARD J F. Contact and rubbing of flat surfaces ［J］. Journal of Applied Physics, 1953, 24(8): 981-988.
［14］ RYAN R R. ADAMS-multibody system analysis software, multibody systems handbook ［M］. Berlin: Springer-Verlag, 1990.
［15］ ZHANG B, YAO B G, KE Y L. A novel posture alignment system for aircraft wing assembly ［J］. Journal of Zhejiang University-Science A, 2009, 10(11): 1624-1630.
[1] 袁瑞峰, 孙志坚, 杨继虎, 杨明, 胡亚才, 俞自涛. 氟塑钢复合管冲蚀磨损性能的试验研究[J]. 浙江大学学报(工学版), 2018, 52(1): 43-49.
[2] 徐兵, 潮群, 张军辉, 李莹. 基于平衡系数的滑靴优化模型[J]. 浙江大学学报(工学版), 2015, 49(6): 1009-1014.
[3] 訚耀保, 付嘉华, 金瑶兰. 射流管伺服阀前置级冲蚀磨损数值模拟[J]. 浙江大学学报(工学版), 2015, 49(12): 2252-2260.
[4] 任立波, 韩吉田, 赵红霞. 单沉浸管流化床内离散颗粒数值模拟[J]. 浙江大学学报(工学版), 2015, 49(1): 150-156.
[5] 王宣银, 程佳. 4TPS-1PS四自由度并联电动平台动力学建模与位姿闭环鲁棒控制[J]. J4, 2009, 43(8): 1492-1496.
[6] 刘少光 吴进明 张升才 胡小海 荣淑杰 李志章. 氮气保护对纳米复合涂层组织与性能的影响[J]. J4, 2008, 42(3): 493-497.
[7] 陈卫祥 涂江平 王浪云 王玉琮 刘新宽 CHARLS O L K. 铝合金上电沉积Ni-P-CNTs复合镀层及其摩擦性能研究[J]. J4, 2008, 42(11): 2033-2036.
[8] 闫洁 李文春 樊建人 岑可法. 绕流中颗粒与柱体碰撞和磨损的直接数值模拟[J]. J4, 2007, 41(4): 589-593.
[9] 朱流 郦剑 凌国平 王幼文. 超细ATC陶瓷制备及其干滑动磨损研究[J]. J4, 2005, 39(12): 1842-1846.
[10] 宋国良 周俊虎 刘建忠 曹欣玉 岑可法. 浓相气力输送中变径管道优化设计方法的研究[J]. J4, 2005, 39(11): 1788-1792.