Please wait a minute...
浙江大学学报(工学版)  2018, Vol. 52 Issue (2): 333-340    DOI: 10.3785/j.issn.1008-973X.2018.02.016
土木与交通工程     
外伸翼缘加劲钢箱形压弯构件屈曲特性试验
桂成中1, 雷俊卿1, 黄祖慰1, 陈嵘1,2
1. 北京交通大学 土木建筑工程学院, 北京 100044;
2. 北京建筑大学 土木与交通工程学院, 北京 100044
Experimental investigation on buckling behavior of stiffened steel box-section beam-column with external flanges
GUI Cheng-zhong1, LEI Jun-qing1, HUANG Zu-wei1, CHEN Rong1,2
1. School of Civil Engineering, Beijing Jiaotong University, Beijing 100044, China;
2. School of Civil and Transportation Engineering, Beijing University of Civil Engineering and Architecture, Beijing 100044, China
 全文: PDF(8617 KB)   HTML
摘要:

为了研究Q500qE高性能钢外伸翼缘薄壁加劲箱形压弯构件的稳定特性,开展3个Q500qE和1个Q345B的构件模型试验,分析试验构件的荷载-位移曲线、整体和局部屈曲形态.整体屈曲试验结果表明,采用Q500qE高性能钢和设置外伸翼缘可以有效提高薄壁箱形压弯构件极限承载力且能够改善构件整体稳定特性.局部屈曲试验表明,外伸翼缘宽厚比对平面外局部屈曲半波数和局部变位影响较大,故需要根据现有规范中的宽厚比限值要求限制外伸翼缘板局部屈曲.对于构件的极限承载力和屈曲形态,试验结果与弹塑性数值分析结果吻合较好.分别采用允许应力法和极限状态法对Q500qE构件进行稳定验算,与试验结果进行比较,表明现有规范中的相关验算公式适用于验算此类压弯构件.

Abstract:

In order to investigate the stability of stiffened steel thin-walled box-section (SSTB) beam-column members with extended flanges made of the high-performance steel (HPS) Q500qE, three Q500qE and one Q345B member model tests were conducted to analyze the load-displacement curve, the global and local buckling behavior of the test members. The results of the global buckling test show that, by using the HPS Q500qE and setting the extended flanges, the ultimate bearing capacity of the SSTB members can be effectively increased and the overall stability of the components can be improved. However, the local buckling tests show that the numbers of half waves and the local deformation in the out-of-plane direction are greatly affected by the width-to-thickness ratio of extended flanges, so the local buckling of the extended flanges need to be limited by the width-to-thickness ratio in accordance with current design codes. The ultimate loads and buckling behaviors obtained from theelasto-plastic numerical analysis conform well with the results of the model tests. At last, the allowable stress method and the limit state method are applied respectively to validate the stability of such members made of Q500qE, and compared with model tests as well. It shows that the stability equations in current codes can be suitable for such members made of Q500qE.

收稿日期: 2017-03-27 出版日期: 2018-03-09
CLC:  TU392  
基金资助:

国家自然基金资助项目(51178042),大跨度公铁两用斜拉桥关键技术研究资助项目(2014-ZJKJ-03).

通讯作者: 雷俊卿,女,教授,博导.orcid.org/     E-mail: jqlei@bjtu.edu.cn
作者简介: 桂成中(1984-),男,博士生,从事公铁两用斜拉桥稳定等研究.orcid.org/0000-0001-7225-0672,E-mail:guicz.cqu.edu@163.com
服务  
把本文推荐给朋友
加入引用管理器
E-mail Alert
作者相关文章  

引用本文:

桂成中, 雷俊卿, 黄祖慰, 陈嵘. 外伸翼缘加劲钢箱形压弯构件屈曲特性试验[J]. 浙江大学学报(工学版), 2018, 52(2): 333-340.

GUI Cheng-zhong, LEI Jun-qing, HUANG Zu-wei, CHEN Rong. Experimental investigation on buckling behavior of stiffened steel box-section beam-column with external flanges. JOURNAL OF ZHEJIANG UNIVERSITY (ENGINEERING SCIENCE), 2018, 52(2): 333-340.

链接本文:

http://www.zjujournals.com/eng/CN/10.3785/j.issn.1008-973X.2018.02.016        http://www.zjujournals.com/eng/CN/Y2018/V52/I2/333

[1] 陈骥. 钢结构稳定理论与设计[M]. 5版.北京:科学出版社, 2011.4.
[2] 童根树. 钢结构的平面内稳定[M]. 北京:中国建筑工业出版社, 2005.10.
[3] 童根树. 钢结构的平面外稳定(修订版)[M]. 北京:中国建筑工业出版社, 2013.1.
[4] CHO Eun-young, SHIN Dong-ku. Elastic web bend-buckling analysis of longitudinally stiffened i-section girders[J]. International Journal of Steel Structures, September, 2011, 11(3):297-313.
[5] 潘永杰, 张玉玲, 田越. Q500qE高性能钢工型梁极限承载力研究[J]. 中国铁道科学, 2011, 32(3):16-20. PAN Yong-jie, ZHANG Yu-ling, TIAN Yue. Study on the ultimate bearing capacity of I-Shaped beam made by high performance steel Q500qE[J].China Railway Science, 2011, 32(3):16-20.
[6] 李国强, 闰晓雷, 陈素文. Q460高强钢焊接箱形压弯构件极限承载力试验研究[J]. 中国土木工程学报, 2012, 45(8):67-73. LI Guo-qiang, YAN Xiao-lei, CHEN Su-wen. Experimental study on the ultimate bearing capacity of welded box section columns using Q460 high strength steel in bending and axial compression[J].China Civil Engineering.Journal, 2012, 45(8):67-73.
[7] 班慧勇, 施刚, 石永久. Q460高强钢焊接箱形截面轴压构件整体稳定性能研究[J]. 建筑结构学报, 2013, 34(1):22-29. BAN Hui-yong, SHI Gang, SHI Yong-jiu. Overall buckling behavior of Q460 high strength steel welded box section columns under axial compression[J]. Journal of Building Structures, 2013, 34(1):22-29.
[8] 郭彦林, 陈绍蕃. 冷弯薄壁槽钢短柱局部屈曲后相关作用的弹塑性分析[J]. 土木工程学报, 1990, 23(3):36-46. GUO Yan-lin, CHEN Shao-fan. Elastioplastic analysis and experimental studies of locally buckled cold-formed thin-walled channel sections[J]. China Civil Engineering Journal, 1990, 23(3):36-46.
[9] 王春生, 王茜, 俞欣. 钢桥塔节段局部稳定试验[J]. 中国公路学报, 2009, 22(6):74-81. WANG Chun-sheng, WANG Qian, YU Xin. Experiment on local buckling of steel bridge tower segment[J]. China Journal of Highway and Transport, 2009, 22(6):74-81.
[10] 狄谨. 钢箱梁梯形肋加劲板受力性能与设计方法研究[D]. 西安:长安大学, 2009. DI Jin. Research on the mechanical behavior and design method of trapezoidal stiffened plate in steel box girder[D]. Xian:Chang'an University doctoral dissertation, 2009.
[11] 鞠晓臣,田越,赵欣欣. Q500qE高强钢压杆稳定研究[J]. 铁道建筑, 2015(10):80-84. JU Xiao-chen, TIAN Yue, ZHAO Xin-xin. Research of compression stability of Q500qE high strength steel rod[J]. Railway Engineering, 2015(10):80-84.
[12] JSCE. 座屈設計ガイドライン[S]. 第2版, 东京. 2005. JSCE. Guidelines for stability design of steel structures.[S].2ndEd Tokyo:2005.
[13] JTG D64.公路钢桥设计规范[S]. 北京:人民交通出版社, 2015. JTG D64. Design specification for highway steel bridge[S]. Beijing:China Communications Press, 2015.
[14] J461-2017.铁路桥梁钢结构设计规范[S]. 北京:国家铁路局, 2017.5. TB10091-2017, J461-2017. Code fordesign on steel structure of railway bridge[S]. Beijing:National Railway Administration of the People's Republic of China, 2017.5.
[15] AASHTO LRFD. AASHTO LRFD Bridge design specifications[S]. Washington:American Association of State Highway and Transportation Officials, 2012.
[16] 王萌,钱凤霞,杨维国. 低屈服点钢材与Q345B和Q460D钢材本构关系对比研究[J]. 工程力学, 2017, 34(2):60-68. WANG Meng, QIAN Feng-xia, YANG Wei-guo, Comparison study on constitutive relationship of low yielding point steels, Q345B steel and Q460 steel[J]. Engineering Mechanics, 2017, 34(2):60-68.
[17] JOHNSTON Bruce Gilbert. Guide to stability design criteria for metal structures3rded[M].[S.l] Wiley, 1976.
[18] 欧阳丹丹,付波,童根树. 矩形钢管截面延性等级和板件宽厚比相关关系[J]. 浙江大学学报:工学版,2016, 50(2):272-281. OUYANG Dan-dan, FU Bo, TONG Gen-shu. Ductility grading of rectangular steel tube section and width-thickness ratio correlation[J]. Journal of Zhejiang University:Engineering Science, 2016, 50(2):272-281.
[19] PILLAI, Unnikrishna SREEDHARAN. Review of recent research on the behavior of beam-columns under biaxial bending[R]. Kingston, Ontario:Royal Military College of Canada, 1970.

No related articles found!