Please wait a minute...
Chinese Journal of Engineering Design  2018, Vol. 25 Issue (4): 402-408    DOI: 10.3785/j.issn.1006-754X.2018.04.006
    
Structure design of novel turbine pneumatic starter motor
SUN Jiang-hong1, DU Hong-chen1, YU Chuan-xin2, ZHANG Qi-liang1
1. School of Electrical and Mechanical, Beijing Information Science and Technology University, Beijing 100192, China;
2. Ellem Industrial(Shanghai) Co., Ltd., Shanghai 200040, China
Download: HTML     PDF(3504KB)
Export: BibTeX | EndNote (RIS)      

Abstract  

According to the characteristics of engineering vehicles, on the basis of engine configuration,a novel turbine pneumatic starter motor is designed. Some innovations was applied to the devices in starter drive, such as gear propulsion and the installing connection, and the gear clash was avoided, and the small volume, good strength, reliable transmission, long service lifetime and convenient exchanging of small gears were realized. The two stage impact turbine rotor was used on the powerplant mounting system and the intake port was made up of two stators and two rotors raising the gas kinetic energy utilization. The power transmission assembly was improved based on the ratchet clutch, the rolling friction and bearing supports were used to make the piston axial travel by the air through airway interface, which decreased the number of parts and friction. The planetary reducer was used on the decelerator assembly that could run on low speed, which had a good advantage of light weight, small volume, big torque and overload, little friction and simple structure. The in-situ test was made on the motor. The experiment showed that the structure was proportion to the car engine and more adaptive to the engine starting characteristics and requirement, which could be applied on the start of locomotive engine. The motor had wider source conditions, and the vehicles could be started multi-times without air admission, which made the start more reliable. The structure design provides an alternative way for engine starting, which also plays a role in promoting the domestic pneumatic starter motor.



Key wordsturbine      pneumatic starter motor      engine      structure design     
Received: 18 October 2016      Published: 28 August 2018
CLC:  TH138.51  
Cite this article:

SUN Jiang-hong, DU Hong-chen, YU Chuan-xin, ZHANG Qi-liang. Structure design of novel turbine pneumatic starter motor. Chinese Journal of Engineering Design, 2018, 25(4): 402-408.

URL:

https://www.zjujournals.com/gcsjxb/10.3785/j.issn.1006-754X.2018.04.006     OR     https://www.zjujournals.com/gcsjxb/Y2018/V25/I4/402


新型涡轮式气启动马达的结构设计

针对工程车辆使用特点和发动机的配置需求,设计了一种新型涡轮式气启动马达,通过对单向器、齿轮推进装置以及连接装置等进行结构创新,避免了顶齿现象发生,且它具有体积小、强度高、传动可靠、寿命长以及小齿轮拆换方便等优点。动力总成设计采用双级冲击式涡轮转子,由2个定子和2个转子组成气道,提高了气体动能利用率。传动总成设计是在现有棘轮式单向器基础上加以改进,采用滚动摩擦和轴承支承结构,使得空气通过气路接口推动活塞轴向移动,减少了零件个数及摩擦。减速总成设计采用行星减速器,可实现极低速运转,同时具有质量轻、体积小、转矩和过载能力大、摩擦少且结构简单等优点。对该马达进行现场试验测试,试验结果表明,该结构与汽车发动机更为匹配,更能满足发动机启动要求,使机动车发动机顺利启动;其适应气源条件更宽,在无补气条件下可实现车辆多次启动,使得车辆气启动更为可靠。该新型气启动马达为发动机启动提供了一种选择,也对国内气动马达的发展起到了促进作用。


关键词: 涡轮式,  气启动马达,  发动机,  结构设计 
[[1]]   王娅萍,白莹,王艳旭,等.发动机气起动失败的原因分析[J].内燃机动力与装置,2011(5):62-64. WANG Ya-ping, BAI Ying, WANG Yan-xu, et al. Analysis of the reason for engine air start-up failure[J]. Internal Combustion Engine & Powerplant, 2011(5):62-64.
[[2]]   肖静,王会良,冯春秋,等.某型号柴油机气马达启动失败故障分析[J].内燃机与配件,2013(3):13-17. XIAO Jing, WANG Hui-liang, FENG Chun-qiu, et al. Failure analysis of gas motor failed to start in diesel engine[J]. Internal Combustion Engine & Parts, 2013(3):13-17.
[[3]]   饶俊良,陈毅培.防爆无轨胶轮车气启动马达的选用及匹配研究[J].矿山机械,2010,38(7):57-58. RAO Jun-liang, CHEN Yi-pei. Research on the match and selection of the air motor for the explosion-proof trackless rubber-tyred locomotive[J]. Mining & Processing Equipment, 2010, 38(7):57-58.
[[4]]   朱辰元,张学庸,吴关清.涡轮式空气起动马达的研制[J].柴油机,1998(6):15-17. ZHU Chen-yuan, ZHANG Xue-yong, WU Guan-qing. Development of turbine type air starting motor[J]. Diesel Engine, 1998(6):15-17.
[[5]]   MARUMO R, TOKHI O M. Intelligent modeling and control of a pneumatic motor[C]//Canadian Conference on Electrical and Computer Engineering, Niagara Falls, Ontario, May 2-5, 2004.
[[6]]   WANG J, PU J, WONG C B, et al. Robust servo motion control of air motor system[C]//UKACC International Conference on Control, Exeter, Sep.2-5, 1996.
[[7]]   BARR L, SPENCE S, THORNHILL D, et al. A numerical and experimental performance comparison of an 86 mm radial and back swept turbine[J]. ASME Turbo Expo:Power for Land, Sea, and Air, 2009, 7:1235-1244.
[[8]]   周明连,张金英.气动齿轮马达静态特性的理论与实验研究[J].液压与气动,2005(9):62-64. ZHOU Ming-lian, ZHANG Jin-ying. Theoretical and experimental study of the pneumatic gear motor[J]. Chinese Hydraulics & Pneumatics, 2005(9):62-64.
[[9]]   林文友,梁前超,王平,等.柴油机大功率双转子气动马达的优化设计与实验分析[J].中国修船,2007,20(2):18-21. LIN Wen-you, LIANG Qian-chao, WANG Ping, et al. Optimization and experiment analysis of high power double rotators air starting on diesel engine[J]. China Ship Repair, 2007, 20(2):18-21.
[[10]]   张林慧.涡轮式气启动马达设计[J].煤矿机电,2015,(3):11-13. ZHANG Lin-hui. Design of pneumatic turbo-starting motor[J]. Colliery Mechanical & Electrical Technology, 2015(3):11-13.
[[11]]   周生伟,刘桂英,张峰,等.大功率发动机气起动马达的选型分析[C]//第十八届全国大功率柴油机学术年会论文集.[2016-10-06]. http://www.doc88.com/p-8042286816913.html. ZHOU Sheng-wei, LIU Gui-ying, ZHANG Feng, et al. Study on the air starter motor for high power engine[C]//Proceedings of the 18th National Conference on High Power Diesel Engine.[2016-10-06]. http://www.doc88.com/p-8042286816913.html.
[[12]]   尹鹏.双涡轮空气启动马达关键技术研究[D].广州:华南理工大学机械与汽车工程学院,2015:13-16. YIN Peng. The research about the key technology of turbo-twin air starter motor[D]. Guangzhou:South China University of Technology, School of Mechanical and Automatic Engineering, 2015:13-16.
[[13]]   屈盛官,尹鹏,李小强,等.一种空气启动马达双涡轮驱动装置:CN203640901U[P].2014-06-11. QU Guan-sheng, YIN Peng, LI Xiao-qiang, et al. A double turbine driving system of air starting:CN203640901U[P]. 2014-06-11.
[[14]]   杨策,施新.径流式叶轮机械理论及设计[M].北京:国防工业出版社,2004:4-14. YANG Ce, SHI Xin. Theory and design of radial-flow impeller[M]. Beijing:National Defense Industry Press, 2004:4-14.
[[15]]   李富成.低压反击涡轮式气动马达主要参数设计计算[J].凿岩机械气动工具,2000(1):13-23. LI Fu-cheng. Design and calculation of main parameters of low pressure counterattack turbine air motor[J]. Rock Drilling Machinery & Pneumatic Tools, 2000(1):13-23.
[[16]]   李富成.复速级冲击涡轮式气动马达设计计算[J].凿岩机械气动工具,2002(2):23-30. LI Fu-cheng. Design and calculation of re-level impact turbine pneumatic motor[J]. Rock Drilling Machinery & Pneumatic Tools, 2002(2):23-30.
[[17]]   徐丛国.挖掘机回转马达总成技术研究及回转系统机液联合仿真[D].贵州:贵州大学机械工程学院,2015:2-5. XU Cong-guo. Study on rotary motor assembly technology of excavator and co-simulation of hydraulic system of rotary system[D]. Guizhou:Guizhou University, School of Mechanical Engineering, 2015:2-5.
[1] Yang DING,Minglu ZHANG,Xin JIAO,Manhong LI. Biomimetic structure design and compliant motion control for hexapod robot driven by joint motors[J]. Chinese Journal of Engineering Design, 2023, 30(2): 154-163.
[2] Ze-jun WEN,Xiang-heng MENG,Zhao XIAO,Fan ZHANG. Sensitivity analysis of airfoil aerodynamic characteristics based on NT-net method and Morris method[J]. Chinese Journal of Engineering Design, 2022, 29(4): 438-445.
[3] Hao ZHOU,Shang-lin LIU,Kai-hong YANG,Si-yang ZHOU,Qian ZHANG. Research on prediction method of driving load of shield machine based on mutual information and support vector regression[J]. Chinese Journal of Engineering Design, 2022, 29(3): 286-292.
[4] LI Yang, NIE Yu-fei. Design and analysis of heat insulation sealing door of sodium combustion test plant[J]. Chinese Journal of Engineering Design, 2022, 29(1): 115-122.
[5] XU Chang-feng, ZHOU You-hang, XIAO Jia-qi, HE Dong-ke, ZHAO Yu. Research on optimal process parameters of sepiolite spiral stirred mill[J]. Chinese Journal of Engineering Design, 2022, 29(1): 51-58.
[6] ZHANG Ai-yun, WANG Ji-hua, GAO Wei, ZHANG Mei-juan. Design of VVT engine rotor defect detection system based on machine vision[J]. Chinese Journal of Engineering Design, 2021, 28(6): 776-784.
[7] ZHENG Yu-chen, JU Feng, WANG Dan, SUN Jing-bin, WANG Ya-ming, CHEN Bai. Design and control research of aeroengine blade detection robot[J]. Chinese Journal of Engineering Design, 2021, 28(5): 625-632.
[8] LIU Shu-qin, LIU Ruo-chen, SUN Jian-zhong, ZHANG Jin-wu. Research on on-line electrostatic monitoring method for wear state of wind turbine gearbox[J]. Chinese Journal of Engineering Design, 2021, 28(2): 163-169.
[9] WU Bo, ZHANG Feng-hua, TIAN Feng, CU Qiang-yi. Operating time prediction of heat storage device in avionics module[J]. Chinese Journal of Engineering Design, 2021, 28(1): 48-55.
[10] LI Peng-ju, MAO Peng-jun, GENG Qian, FANG Qian, ZHANG Jia-rui, HUANG Chuan-peng. Design and test analysis of matrix cutting system of eucommia ulmoides grafting robot[J]. Chinese Journal of Engineering Design, 2020, 27(6): 744-752.
[11] WANG Zhi-li, ZHU Ting-zhong, CHEN Zhi-yong, XI-Bo, JIA Xiao-ping. Design of mechanical structure and hydraulic system of tubular turbine governor[J]. Chinese Journal of Engineering Design, 2020, 27(6): 753-764.
[12] BAI Zhong-hang, SONG Xian-xian, LI Mei, ZHANG Peng. Research on solving method of product ergonomics problem based on virtual simulation and TRIZ[J]. Chinese Journal of Engineering Design, 2020, 27(5): 541-551.
[13] REN Meng-yi, CAO En-guo, ZHAO Yong-wu, YANG Bin, CUI Yu-tian. Design and optimization of a passive exoskeleton mechanical foot[J]. Chinese Journal of Engineering Design, 2020, 27(2): 199-211.
[14] TANG Liang, HE Ren-jie, GONG Fa-yun, LI Fei-yang, LIU Guan-jun, YANG Min. Internal excitation law research and dynamic characteristic optimization of wind turbine gearbox under varying wind load[J]. Chinese Journal of Engineering Design, 2020, 27(2): 212-222.
[15] LI Yao-hua, ZHANG Hai-feng, WEI Qi-dong. Model for determination of civil aircraft level of repair based on EAHP-FCE method[J]. Chinese Journal of Engineering Design, 2019, 26(5): 544-551.