Please wait a minute...
工程设计学报
工程设计学报  2021, Vol. 28 Issue (5): 576-584    DOI: 10.3785/j.issn.1006-754X.2021.00.075
优化设计     
基于相似理论的掘进机主动激振截割性能研究
谢苗, 张保国, 王鹏飞, 李政
辽宁工程技术大学 机械工程学院， 辽宁 阜新 123000
Research on active excitation cutting performance of roadheader based on similarity theory
XIE Miao, ZHANG Bao-guo, WANG Peng-fei, LI Zheng
School of Mechanical Engineering， Liaoning Technical University， Fuxin 123000， China
 全文: PDF(4670 KB)   HTML
摘要： 针对目前煤矿井下掘进机截割时关键零部件易损坏及截割性能不佳，但难以在实验室内进行相关研究的问题，以EBZ160掘进机为原型，基于相似理论制造了实验样机，并提出一种主动激振截割方式。首先，基于掘进机实验样机的工作原理和动力学理论，利用ANSYS Workbench软件对实验样机进行模态仿真分析，并基于力锤法进行了模态试验，得到了空载状态下实验样机的前6阶固有频率与模态振型。然后，以截割比能耗为评价指标，对有无主动激振截割方式下掘进机实验样机的截割性能进行研究。结果表明，掘进机实验样机前6阶固有频率的仿真值与试验值的最大相对误差为9.92%，验证了模态仿真分析结果的准确性，可为后续激振频率的选取提供依据；无主动激振时掘进机实验样机的截割比能耗为0.077 6 kW·h/m3，有主动激振时为0.051 2 kW·h/m3，说明所提出的主动激振截割方式的性能较好。研究结果为掘进机截割方式的拓展提供了新方向，并为掘进机的结构优化及截割效率提升提供了实验依据。
Abstract: Aiming at the problem that the key components of the roadheader under the coal mine are easily damaged and its cutting performance is poor during cutting, but it is difficult to carry out related research in the laboratory, taking the EBZ160 roadheader as the prototype, an experimental prototype was manufactured based on the similarity theory, and an active vibration cutting method was proposed. Firstly, based on the working principle and dynamics theory of the roadheader experimental prototype, the modal simulation analysis for the experimental prototype was carried out by using the ANSYS Workbench software, and the modal test was carried out based on the hammer method. The first six natural frequencies and modal shapes of the experimental prototype under the no-load state were obtained. Then, taking the cutting specific energy consumption as the evaluation index, the cutting performance of the roadheader experimental prototype under the cutting mode with or without active excitation was studied. The results showed that the maximum relative error between the simulated value and the test value of the first six natural frequencies of the roadheader experimental prototype was 9.92%, which verified the accuracy of the modal simulation analysis results and could provide a basis for the selection of subsequent excitation frequency; the cutting specific energy consumption of the roadheader experimental prototype without and with active excitation was 0.077 6 kW·h/m3 and 0.051 2 kW·h/m3, respectively, which indicated that the performance of the proposed active excitation cutting method was relatively good. The research results provide a new direction for the expansion of roadheader cutting methods, and provide an experimental basis for the structure optimization and cutting efficiency improvement of the roadheader.
收稿日期: 2020-11-30 出版日期: 2021-10-28
CLC:  TD 421  
基金资助: 国家自然科学基金资助项目（51874158）
作者简介: 谢苗（1980—），女，辽宁大连人，教授，博士，从事综掘、综采成套装备研究，E-mail：412442029@qq.com，https：//orcid.org/0000-0002-2980-0365；
服务　　
把本文推荐给朋友
加入引用管理器
E-mail Alert
RSS
作者相关文章　　

引用本文:

谢苗, 张保国, 王鹏飞, 李政. 基于相似理论的掘进机主动激振截割性能研究[J]. 工程设计学报, 2021, 28(5): 576-584.

XIE Miao, ZHANG Bao-guo, WANG Peng-fei, LI Zheng. Research on active excitation cutting performance of roadheader based on similarity theory. Chinese Journal of Engineering Design, 2021, 28(5): 576-584.

链接本文:

https://www.zjujournals.com/gcsjxb/CN/10.3785/j.issn.1006-754X.2021.00.075    或    https://www.zjujournals.com/gcsjxb/CN/Y2021/V28/I5/576

[1] 田立勇,孙业新,于宁,陈洪月,马春莹. 基于组合方式的掘进机导航系统研究[J]. 工程设计学报, 2022, 29(2): 254-262.
[2] 白杨溪, 陈洪月, 陈洪岩, 王鑫, 李建刚. 基于滚筒载荷的采煤机滑靴振动分析及实验验证[J]. 工程设计学报, 2021, 28(3): 358-366.
[3] 白杨溪, 陈洪月, 陈洪岩, 王鑫. 多约束条件下采煤机摇臂横向振动分析及试验验证[J]. 工程设计学报, 2020, 27(6): 707-712.
[4] 李琴, 傅文韬, 黄志强, 徐子扬, 陈奔. 硬地层中新型PDC齿破岩机理及试验研究[J]. 工程设计学报, 2019, 26(6): 635-644.
[5] 朱爱斌, 王步康, 田超, 周尧, 陈渭. 履带行走机构功率损耗分析系统设计与实现[J]. 工程设计学报, 2011, 18(6): 444-448.
[6] 毛君, 陈洪月, 董纯友, 赵晓光. 掘锚联合机行走稳定性仿真研究[J]. 工程设计学报, 2011, 18(5): 349-353.
[7] 周游, 李国顺, 唐进元. 截齿截割煤岩的LS_DYNA仿真模拟[J]. 工程设计学报, 2011, 18(2): 103-108.
[8] 赵丽娟, 王乘云. 采煤机截割部建模与动力学仿真研究[J]. 工程设计学报, 2010, 17(2): 119-123.