Please wait a minute...
工程设计学报
工程设计学报  2016, Vol. 23 Issue (3): 244-250    DOI: 10.3785/j.issn. 1006-754X.2016.03.008
建模、分析、优化和决策     
基于数值仿真的气动喷射阀回流间隙的优化
魏新明, 沈平, 单修洋, 李渭松
中南大学 机电工程学院, 湖南 长沙 410083
Optimization of the backflow gap of pneumatic jetting valve based on numerical simulation
WEI Xin-ming, SHEN Ping, SHAN Xiu-yang, LI Wei-song
College of Mechanical and Electrical Engineering, Central South University, Changsha 410083, China
 全文: PDF(2757 KB)   HTML
摘要：

气动喷射阀是微电子封装中不可或缺的封装设备,但现有气动喷射阀在喷射高黏胶液时仍不能完全满足工业界对胶滴一致性的需求,原因在于其喷射高黏胶液时常出现因喷射速度太小而导致的挂胶漏喷现象.要减小上述现象的发生概率,就必须提高现有气动喷射阀的高黏流体喷射能力.回流间隙作为气动喷射阀的关键尺寸,直接影响着喷射阀的喷射能力.为了通过优化回流间隙来提高喷射能力,首先建立气动喷射阀的胶液喷射数值仿真模型并通过实验验证其可靠性,同时基于不同回流间隙的仿真数据建立了相应的高斯拟合模型.然后利用拟合模型以胶滴滴落速度为优化目标对回流间隙进行优化,通过优化前后的喷射对比验证了优化结果的可靠性,最后获得气动喷射阀的最优回流间隙.
关键词： 气动喷射阀;  回流间隙;  点胶;  微电子封装;  优化设计    
Abstract:

Pneumatic jetting valve plays an indispensable role in the microelectronic packaging.However,the current pneumatic jetting valves can't meet the industrial requirement of droplet consistency completely for the frequent occurrence of jetting omission when it is used to jet high-viscosity adhesives.Jetting capacity must be enhanced to reduce the probability of the problem occurrence.As a key dimension of pneumatic jetting valve,the size of backflow gap influences its jetting capacity directly.In order to improve jetting capacity by optimizing backflow channes,a numerical model of the jetting process was established firstly and its validity was verified by corresponding experiment.Meanwhile,a Gaussian fitting model was built based on simulation data with different backflow channels.After that,the model was utilized to optimize the size of backflow gap by choosing droplet speed as optimization objective.The reliability of optimization results was verified by comparison of the jetting performance before and after optimization.Finally,the optimal size of backflow gap of pneumatic jetting valve was obtained.
Key words: pneumatic jetting valve    backflow gap    fluid dispensing    microelectronic packaging    optimization design
收稿日期: 2015-12-09 出版日期: 2016-06-28
CLC:  TN4  
基金资助:

国家重点基础研究发展计划(973计划)资助项目(2011CB013104).
通讯作者: 沈平(1983-),男,陕西宝鸡人,博士,从事系统建模与控制等研究,E-mail:ppguitar1983@sina.com.     E-mail: ppguitar1983@sina.com
作者简介: 魏新明(1990-),男,湖南衡阳人,硕士,从事微电子封装工艺与设备研究,E-mail:w_xm2012@yeah.net.http://orcid.org/0000-0002-2606-9335;沈平(1983-),男,陕西宝鸡人,博士,从事系统建模与控制等研究,E-mail:ppguitar1983@sina.com.
服务　　
把本文推荐给朋友
加入引用管理器
E-mail Alert
RSS
作者相关文章　　
魏新明
沈平
单修洋
李渭松

引用本文:

魏新明, 沈平, 单修洋, 李渭松. 基于数值仿真的气动喷射阀回流间隙的优化[J]. 工程设计学报, 2016, 23(3): 244-250.

WEI Xin-ming, SHEN Ping, SHAN Xiu-yang, LI Wei-song. Optimization of the backflow gap of pneumatic jetting valve based on numerical simulation. Chinese Journal of Engineering Design, 2016, 23(3): 244-250.

链接本文:

https://www.zjujournals.com/gcsjxb/CN/10.3785/j.issn. 1006-754X.2016.03.008    或    https://www.zjujournals.com/gcsjxb/CN/Y2016/V23/I3/244

[1] 高尚通.跨世纪的微电子封装[J].半导体情报,2000,37(6):1-7. GAO Shang-tong.Microelectronics packaging marching towards the new century[J].Semiconductor Information,2000,37(6):1-7.

[2] BABIARZ A J.Jetting small dots of high viscosity fluids for packaging applications[J].Semiconductor International,2006,29(9):2-8.

[3] NGUON B,JOUANEH M.Design and characterization of a precision fluid dispensing valve[J].The International Journal of Advanced Manufacturing Technology,2004,24(3/4):251-260.

[4] KOIDE A,SASAKI Y,YOSHIMURA Y,et al.Micromachined dispenser with high flow rate and high resolution[C]//Proceedings IEEE 13th Annual International Conference on Micro Electro Mechanical Systems.Miyavaki,Jan.23-27,2000.

[5] LEWIS A,BABIARZ A.Conductive adhesive dispensing process considerations[C]//Proceedings of the Technical Program:National Electronic Packaging and Production Conference.Anaheim,Feb.26-Mar.1,1999.

[6] MARONGELLI S R,DIXON D,PORCARIET S,et al.Practical production uses of SMT adhesives[C]//Proceeding of the IEEE/CPMT International Electronic Manufacturing Technology (IEMT) Symposium.Tokyo,1998:147-155.

[7] 孙道恒,高俊川,杜江,等.微电子封装点胶技术的研究进展[J].中国机械工程,2011,22(20):2513-2519. SUN Dao-heng,GAO Jun-chuan,DU Jiang,et al.Advances in fluid dispensing technology for micro-electronics packaging[J].China Mechanical Engineering,2011,22(20):2513-2519.

[8] 赵翼翔,陈新度,陈新.微电子封装中的流体点胶技术综述[J].液压与气动,2006(2):52-54. ZHAO Yi-xiang,CHEN Xin-du,CHEN Xin.An overview of fluid dispensing technology for micro-electronics packaging[J].Chinese Hydraulics & Pneumatics,2006(2):52-54.

[9] CHEN X B.Modeling and control of fluid dispensing process:a state-of-the-art review[J].The International Journal of Advanced Manufacturing Technology,2009,43(3/4):276-286.

[10] 李章平,邓圭玲.精密点胶螺杆泵胶液流动分析与数值仿真[J].中国机械工程,2007,18(17):2102-2107. LI Zhang-ping,DENG Gui-ling.Numerical simulations and analysis of three-dimensional flows in the archimedes pump on dispensing[J].China Mechanical Engineering,2007,18(17):2102-2107.

[11] PIRACCI A F.Advantages of non-contact dispensing in SMT assembly processes[C]//SMTA International Conference Proceedings.Asymtek,2000-09-24.

[12] PIRACCI A F.Practical production applications for jetting technology[C]//Proceedings of APEX Conference.Long Beach,CA,2000:1-6.

[13] QUINONES H,BABIARZ A,DECK C,et al.Fluid jetting for next generation packages[C]//Proceedings of Packaging Technolog.Berlin,2002:1-8.

[14] NGUYEN Q H,CHOI S B.Modeling of unsteady laminar flow based on steady solution in jetting dispensing process[J].IEEE Transactions on Electronics Packaging Manufacturing,2008,31(2):134-142.

[15] SHAN X Y,CHEN Y,PENG X,et al.Modeling of laminar fluid flow in jet dispensing process[C].15th International Conference on Electronic Packaging Technology (ICEPT).Chengdu,Aug.12-15,2014.

[16] QUOC H N,HAN Y M,CHOI S B,et al.Dynamic characteristics of a new jetting dispenser driven by piezostack actuator[J].IEEE Transactions on Electronics Packaging Manufacturing,2008,31(3):248-259.

[17] CHEN Y,WANG F L,LI H X,et al.Experimental and modeling study of high-viscosity silicone jet dispensing process for LED packaging[C].15th International Conference on Electronic Packaging Technology (ICEPT).Chengdu,Aug.12-15,2014.

[18] 彭先安.面向高性能LED封装的气动喷射阀喷胶性能研究[D].长沙:中南大学机电工程学院,2014:85-90. PENG Xian-an.Research on the performance of pneumatic jetting valve in the dispensing of high-performance LED package[D].Changsha:Central South University,College of Mechanical and Electrical Engineering,2014:85-90.
[1] 孙光明,王奕苗,万仟,弓堃,汪文津,赵坚. 考虑装配变形的精密机床床身优化设计[J]. 工程设计学报, 2022, 29(3): 318-326.
[2] 陈振, 李涛, 薛晓伟, 周阳, 敬爽, 陈言. 基于模糊综合评价法的可控震源振动器平板疲劳可靠性分析与优化[J]. 工程设计学报, 2021, 28(4): 415-425.
[3] 张锦, 刘佩珊, 殷玉枫. Y形旋转超声波马达的设计与动态特性分析[J]. 工程设计学报, 2021, 28(2): 248-254.
[4] 刘永江, 彭宣霖, 唐雄辉, 李华, 齐紫梅. 轴流散热风机共振失效分析与优化设计[J]. 工程设计学报, 2021, 28(2): 203-209.
[5] 魏巍, 林载盛. 基于RIR-MOO的定制产品优化设计方法研究[J]. 工程设计学报, 2020, 27(5): 592-599.
[6] 孙月海, 唐二星. 弧齿锥齿轮基本参数优化设计[J]. 工程设计学报, 2020, 27(5): 616-624.
[7] 孙世峰, 高常青, 杨波, 徐征和. 基于试验设计与有限元仿真的辐射井水平钻机承载部件优化设计[J]. 工程设计学报, 2019, 26(6): 683-690.
[8] 杨迎新, 周坚, 黄奎林, 任海涛, 陈炼. 定向随钻扩孔PDC钻头优化设计及应用[J]. 工程设计学报, 2018, 25(6): 668-674.
[9] 万建成, 江明, 杨磊, 刘晨. 大截面碳纤维导线卡线器夹嘴优化设计[J]. 工程设计学报, 2018, 25(6): 675-682.
[10] 卢清华, 黄铭贤, 陈为林. 平面阻尼型欠驱动夹持器的多模式参数优化设计[J]. 工程设计学报, 2018, 25(6): 690-696.
[11] 康小云, 翟之平, 巩勇智, 程海鹰, 吴雅梅. 偏心伸缩杆式输送装置输送性能分析与改进[J]. 工程设计学报, 2017, 24(6): 655-660.
[12] 林权, 刘瑞来. 汽车饰盖CAE分析及成型工艺优化[J]. 工程设计学报, 2017, 24(6): 661-667.
[13] 张小良，林炜锋. 有限元方法在波形弹片设计中的研究与应用[J]. 工程设计学报, 2015, 22(5): 399-404.
[14] 张小良，林炜锋. 有限元方法在波形弹片设计中的研究与应用[J]. 工程设计学报, 2015, 22(4): 399-404.
[15] 苏建宁，王瑞红 ，赵慧娟，张书涛. 基于感性意象的产品造型优化设计[J]. 工程设计学报, 2015, 22(1): 35-41.