Please wait a minute...
工程设计学报  2013, Vol. 20 Issue (4): 344-347    
工程设计理论、方法与技术     
柔性对称微位移放大机构性能分析方法的研究
 刘庆玲
廊坊师范学院 数学与信息科学学院, 河北 廊坊 065000
Study on the performance analysis methods of the compliant symmetric micro-displacement magnifying mechanism
 LIU  Qing-Ling
Institute of Mathematics and Information Science, Langfang Normal College, Langfang 065000, China
 全文: PDF(492 KB)   HTML
摘要: 柔性铰链微位移放大机构的性能分析,通常采用柔度静力学分析方法,该方法分析过程复杂,柔度计算量大.为此,提出一种新的分析方法,将柔性铰链转换为刚性铰链并在其上加一等效刚度系数为k的扭簧,采用虚功原理对机构进行分析求解,推导出微位移放大机构输入位移、输出位移的计算式,进而求得机构的放大比.采用上述方法对柔性八杆对称微位移放大机构进行性能分析,将所得的分析结果与柔度静力学分析法、有限元分析法的分析结果进行对比,三者具有很好的一致性,验证了该方法的正确性.该方法充分利用了机构的对称性,使得分析求解过程得到了很大程度的简化.
关键词: 微位移机构柔性铰链等效刚度 柔度虚功原理    
Abstract: The compliances statics mechanics analysis method is generally used to analyse the performance of the compliant symmetric microdisplacement magnifying mechanism with the flexure hinge, but the analysis process and the compliances calculation are very complicated, so the author presents a new analytical method, in which each flexure hinge is transformed into rigid hinge and added a torsion spring on it whose equivalent stiffness is k, the virtual work principle is used to analyse the transformed mechanism, deduce the simple formulas about the input displacement, output displacement and the magnification ration. This method was used in the performance analysis of the compliant 8bars symmetric microdisplacement magnifying mechanism, the results were contrasted with the results obstained by the compliance statics mechanics analytical method and the finite element, which indicated the consistency among them. The new method makes full use of the symmetry of the mechanism, it greatly simplifies the computation and improves the efficiency.
Key words: micro-displacement mechanism    flexure hinge    equivalent stiffness    compliances    virtual work principle
出版日期: 2013-08-28
基金资助:

国家自然科学基金资助项目(50805008);河北省科技计划项目(12211704).

服务  
把本文推荐给朋友
加入引用管理器
E-mail Alert
RSS
作者相关文章  
刘庆玲

引用本文:

刘庆玲. 柔性对称微位移放大机构性能分析方法的研究[J]. 工程设计学报, 2013, 20(4): 344-347.

LIU Qing-Ling. Study on the performance analysis methods of the compliant symmetric micro-displacement magnifying mechanism. Chinese Journal of Engineering Design, 2013, 20(4): 344-347.

链接本文:

https://www.zjujournals.com/gcsjxb/CN/        https://www.zjujournals.com/gcsjxb/CN/Y2013/V20/I4/344

[1] 李玄, 周双武, 路松, 丁冰晓. 基于二级杠杆机构的二自由度微定位平台设计与分析[J]. 工程设计学报, 2020, 27(4): 533-540.
[2] 何育民, 程婉莹, 朱宝慧, 徐欢欢. 矩形梁裂纹柔度测量方法研究[J]. 工程设计学报, 2017, 24(6): 618-623.
[3] 刘强, 王艾伦. 基于损伤力学的周向拉杆转子整体疲劳损伤研究[J]. 工程设计学报, 2017, 24(5): 572-579.
[4] 刘凯, 曹毅, 周睿, 丁锐, 葛姝翌. 抗压内LET柔性铰链的建模及分析[J]. 工程设计学报, 2016, 23(6): 585-591.
[5] 胡俊峰,郝亚洲,徐贵阳. 基于有限元法的柔性铰链力学模型和性能分析[J]. 工程设计学报, 2014, 21(5): 432-438.
[6] 杨春辉, 刘平安. 圆弧型柔性球铰柔度设计计算[J]. 工程设计学报, 2014, 21(4): 389-392.
[7] 杨启志, 姚斌斌, 庄佳奇, 尹小琴. 基于高频柔性并联激振台柔性转动关节的加工误差分析[J]. 工程设计学报, 2012, 19(3): 170-173.
[8] 温正方, 张景旭, 张丽敏. 五自由度次镜调整机构的研究[J]. 工程设计学报, 2010, 17(6): 473-478.
[9] 刘庆玲, 翁海珊, 邱丽. 新型单边复和型柔性铰链的柔度计算及其性能分析[J]. 工程设计学报, 2009, 16(4): 276-280.
[10] 叶 果, 李 威, 王禹桥, 杨雪峰. 直角切口柔性平行四杆机构的输出位移分析[J]. 工程设计学报, 2009, 16(4): 303-307.
[11] 吕福在, 项占琴, 程耀东. 稀土超磁致伸缩材料微位移机构综合实验研究[J]. 工程设计学报, 2000, 7(2): 42-44.