Please wait a minute...
工程设计学报  2012, Vol. 19 Issue (3): 182-186    
工程设计理论、方法与技术     
单转向轮摆振机理与稳定性研究
 肖闯, 殷智宏
湖南大学 汽车车身先进设计制造国家重点实验室,湖南 长沙 410082
Investigations on mechanism and stability of caster wheel shimmy
 XIAO  Chuang, YIN  Zhi-Hong
The State Key Laboratory of Advanced Design and Manufacturing for Vehicle Body, Hunan University, Changsha 410082, China
 全文: PDF(2092 KB)   HTML
摘要: 为研究典型单转向轮系统摆振机理及稳定性,建立杠杆驱动轮椅车转向轮系统非线性动力学微分方程,应用ODE方法进行求解;搭建了参数可调的转向轮摆振实验装置,利用实验手段研究摆振现象,验证了转向轮系统动力学模型的有效性;并对此动力学模型线性化,进行稳定性分析;利用遗传优化算法对转向轮系统进行参数优化设计,针对实验研究的转向轮摆振实验装置进行稳定性分析,采用增加阻尼轴承的方法改善实验中转向轮系统的稳定性.通过研究转向轮系统参数变化对摆振的影响规律,提出防范摆振的方法,获得具有实用价值的结论:通过增加转向轮拖距长度、合理选择质量参数或者增加系统的阻尼都可以减小甚至消除摆振.因此,该研究具有较好的工程实用价值,并对类似转向轮系统稳定性分析有一定的参考价值.
关键词: 转向轮摆振实验研究稳定性分析优化设计    
Abstract: In order to investigate the mechanism and stability of caster wheel shimmy,2DoFs dynamic model of lever propulsion wheelchair steering wheel was established by analytical mechanics.This dynamic model was derived from Lagrange equation and its numerical solutions were solved by Ordinary Differential Equation (ODE) method.A new physical steering wheel model with adjustable parameters was built to verify the mathematical model.In the experimental stage,the theoretical results obtained from mathematical model as well as the dynamic behavior of towed wheel within different cases were successfully verified by vibration measurements.Stability analysis was conducted by Routh criterion on a linear dynamic model.To avoid the shimmy in the design stage,the genetic algorithm was applied to optimization design of the steering wheel system.Shimmy can be avoided after replacing a damped bearing with a set of reasonable parameters.Based on the stability analysis and optimization design conclusions,the shimmy problem of physical steering wheel has been solved.To avoid and eliminate shimmy,some practical suggestions are offered due to the effects of system parameters on shimmy,for instance,increasing length of the trail,applying a damped bearing and adopting reasonable parameters of geometry and mass.Therefore,the presented method is of good practical engineering value,and it also has a certain useful value for similar steering wheel system stability analysis.
Key words: caster shimmy    experimental investigation    stability analysis    optimization design
出版日期: 2012-06-15
服务  
把本文推荐给朋友
加入引用管理器
E-mail Alert
RSS
作者相关文章  
肖闯
殷智宏

引用本文:

肖闯, 殷智宏. 单转向轮摆振机理与稳定性研究[J]. 工程设计学报, 2012, 19(3): 182-186.

XIAO Chuang, YIN Zhi-Hong. Investigations on mechanism and stability of caster wheel shimmy. Chinese Journal of Engineering Design, 2012, 19(3): 182-186.

链接本文:

https://www.zjujournals.com/gcsjxb/CN/        https://www.zjujournals.com/gcsjxb/CN/Y2012/V19/I3/182

[1] 孙光明,王奕苗,万仟,弓堃,汪文津,赵坚. 考虑装配变形的精密机床床身优化设计[J]. 工程设计学报, 2022, 29(3): 318-326.
[2] 陈振, 李涛, 薛晓伟, 周阳, 敬爽, 陈言. 基于模糊综合评价法的可控震源振动器平板疲劳可靠性分析与优化[J]. 工程设计学报, 2021, 28(4): 415-425.
[3] 张锦, 刘佩珊, 殷玉枫. Y形旋转超声波马达的设计与动态特性分析[J]. 工程设计学报, 2021, 28(2): 248-254.
[4] 刘永江, 彭宣霖, 唐雄辉, 李华, 齐紫梅. 轴流散热风机共振失效分析与优化设计[J]. 工程设计学报, 2021, 28(2): 203-209.
[5] 孙月海, 唐二星. 弧齿锥齿轮基本参数优化设计[J]. 工程设计学报, 2020, 27(5): 616-624.
[6] 魏巍, 林载盛. 基于RIR-MOO的定制产品优化设计方法研究[J]. 工程设计学报, 2020, 27(5): 592-599.
[7] 孙世峰, 高常青, 杨波, 徐征和. 基于试验设计与有限元仿真的辐射井水平钻机承载部件优化设计[J]. 工程设计学报, 2019, 26(6): 683-690.
[8] 杨迎新, 周坚, 黄奎林, 任海涛, 陈炼. 定向随钻扩孔PDC钻头优化设计及应用[J]. 工程设计学报, 2018, 25(6): 668-674.
[9] 万建成, 江明, 杨磊, 刘晨. 大截面碳纤维导线卡线器夹嘴优化设计[J]. 工程设计学报, 2018, 25(6): 675-682.
[10] 卢清华, 黄铭贤, 陈为林. 平面阻尼型欠驱动夹持器的多模式参数优化设计[J]. 工程设计学报, 2018, 25(6): 690-696.
[11] 康小云, 翟之平, 巩勇智, 程海鹰, 吴雅梅. 偏心伸缩杆式输送装置输送性能分析与改进[J]. 工程设计学报, 2017, 24(6): 655-660.
[12] 林权, 刘瑞来. 汽车饰盖CAE分析及成型工艺优化[J]. 工程设计学报, 2017, 24(6): 661-667.
[13] 李强, 毛君, 张明玉, 谢苗. 采煤机截齿三向力测试方案设计及实验研究[J]. 工程设计学报, 2016, 23(5): 506-512.
[14] 魏新明, 沈平, 单修洋, 李渭松. 基于数值仿真的气动喷射阀回流间隙的优化[J]. 工程设计学报, 2016, 23(3): 244-250.
[15] 陈洪月, 刘烈北, 毛君, 宋秋爽, 袁智. 激励与滚筒振动耦合下采煤机动力学特性分析[J]. 工程设计学报, 2016, 23(3): 228-234.