Please wait a minute...
工程设计学报  2009, Vol. 16 Issue (6): 421-426    
工程设计理论、方法与技术     
基于CAE某型汽车发动机前罩壳冲压模设计
 李立君1, 周 健1, 王智文2, 梁志松2
1.中南林业科技大学 机电工程学院,湖南 长沙 410004;2.广西工学院 计算机系,广西 柳州 545006
Design of front-covering-shell stamping mould on an auto engine based on CAE
 LI  Li-Jun1, ZHOU  Jian1, WANG  Zhi-Wen2, LIANG  Zhi-Song2
1.College of Machinery and Electrical Engineering, Centre South University of Forestry and Technology, Changsha 410004, China; 2.Department of Computer Engineering, Guangxi University of Technology, Liuzhou 545006, China
 全文: PDF(4381 KB)   HTML
摘要: 基于机械优化设计的思想,通过对冲压件前罩壳的分析,建立了符合要求的模型.运用Dynaform软件进行CAE分析.由于引入了CAE,冲压成形已从原来的对应力应变进行分析而逐步发展到采用有限元等进行工艺过程的模拟与分析,实现了冲压过程的优化设计.
关键词: 冲压前罩壳CAE技术模具设计    
Abstract: Based on the idea of mechanical optimization design, through the analysis on the front-overing-shell stamping mould, models meeting the requirements were built. The Dynaform software was used for CAE analysis. Because CAE was introduced, press deformation was developed from the original analysis on strain and stress to simulation and analysis of process by finite element method and so on. Finally, press process optimization design was implemented.
Key words: stamping    front-covering-shell    CAE technology    mould design
出版日期: 2009-12-28
:  TH 164  
基金资助:

湖南省教育厅重点项目资助(07A081);中南林业科技大学人才基金资助项目;湖南省教育厅2009年科研资助项目(09C1017)

服务  
把本文推荐给朋友
加入引用管理器
E-mail Alert
RSS
作者相关文章  
李立君
周健
王智文
梁志松

引用本文:

李立君, 周健, 王智文, 梁志松. 基于CAE某型汽车发动机前罩壳冲压模设计[J]. 工程设计学报, 2009, 16(6): 421-426.

LI Li-Jun, ZHOU Jian, WANG Zhi-Wen, LIANG Zhi-Song. Design of front-covering-shell stamping mould on an auto engine based on CAE[J]. Chinese Journal of Engineering Design, 2009, 16(6): 421-426.

链接本文:

https://www.zjujournals.com/gcsjxb/CN/        https://www.zjujournals.com/gcsjxb/CN/Y2009/V16/I6/421

[1] 王炎, 张换高, 刘力萌, 赵磊, 陶涛. 基于基因调优算子的产品平台进化设计研究[J]. 工程设计学报, 2017, 24(3): 241-249,294.
[2] 谢延敏, 何育军, 卓德志, 熊文诚. 高强度钢板U形件热冲压凹模结构拓扑优化[J]. 工程设计学报, 2016, 23(1): 60-66.
[3] 周健, 李立君, 张江, 张锁军, 周冬成. 基于CAE某发动机加强板成形模具的设计[J]. 工程设计学报, 2010, 17(1): 76-80.
[4] 李 军, 李艳辉, 郑金桥. 基于KBE的冲压件自评价工艺方案设计[J]. 工程设计学报, 2006, 13(3): 140-144.