Please wait a minute...
工程设计学报  2010, Vol. 17 Issue (6): 473-478    
机电产品工程设计     
五自由度次镜调整机构的研究
 温正方1,2, 张景旭1, 张丽敏1
1.中国科学院 长春光学精密机械与物理研究所,吉林 长春130033;
2.中国科学院 研究生院,北京100039
Research of five-degree-of-freedom adjustment mechanism
 WEN  Zheng-Fang1,2, ZHANG  Jing-Xu1, ZHANG  Li-Min1
1. Changchun Institute of Optics, Fine Mechanics and Physics, Chinese Academy of Sciences, Changchun 130033, China;
2.Graduate School of the Chinese Academy of Science, Beijing 100039, China
 全文: PDF(2066 KB)   HTML
摘要: 在同轴望远镜系统中,主镜和次镜的相对位置和姿态有非常严格的要求,需要将次镜设计成多自由度可以调整的机构.针对次镜调整机构的性能要求,提出一套由二维 XY 移动平台和三维Tip/Tilt/Focus平台组合成的五自由度次镜调整机构方案.其中三维Tip/Tilt/Focus平台由3个驱动器、定平台与动平台组成,驱动器与动平台之间由柔性铰链连接,通过3个驱动器的伸缩和柔性铰链的转动来实现动平台的三自由度运动.对三维Tip/Tilt/Focus平台的运动学原理作了详细介绍,深入地讨论柔性铰链弯曲刚度和轴向刚度与几何参数的关系.研究结果为五维调整机构及柔性铰链的设计提供客观依据,具有较大的实际意义.
关键词: 次镜调整机构驱动器柔性铰链弯曲刚度轴向刚度    
Abstract:  In the coaxial telescope system,the relative position and pose between primary mirror and secondary mirror are strictly required. Therefore,a multi-degree-of-freedom adjustment mechanism for secondary mirror is needed. To satisfy the specifications of the adjustment mechanism for secondary mirror,a device consisted of a XY translation stage and a Tip/Tilt/Focus stage was presented. The Tip/Tilt/Focus stage was composed of three actuators, fixing and moving platform which were connected by flexure hinges. The motion of the platform was performed by the extension of three actuators and the rotation of flexure hinges. The kinematic principles of Tip/Tilt/Focus platform were introduced with details, then the flexure hinges were considered,and the relationship between geometric parameters of flexure hinges and bending & axial rigidity was detailed. This paper provides an objective basis on design of five-degree-of-freedom adjustment mechanism and flexure hinges, which could be applied in precision engineering.
Key words:  adjustment mechanism of secondary mirror    actuator    flexure hinges    bending rigidity    axial rigidity
出版日期: 2010-12-28
基金资助:

中国科学院三期创新项目

服务  
把本文推荐给朋友
加入引用管理器
E-mail Alert
RSS
作者相关文章  
温正方
张景旭
张丽敏

引用本文:

温正方, 张景旭, 张丽敏. 五自由度次镜调整机构的研究[J]. 工程设计学报, 2010, 17(6): 473-478.

WEN Zheng-Fang, ZHANG Jing-Xu, ZHANG Li-Min. Research of five-degree-of-freedom adjustment mechanism[J]. Chinese Journal of Engineering Design, 2010, 17(6): 473-478.

链接本文:

https://www.zjujournals.com/gcsjxb/CN/        https://www.zjujournals.com/gcsjxb/CN/Y2010/V17/I6/473

[1] 段韦婕,秦慧斌,刘荣,李中一,白绍平. 可重构变刚度柔性驱动器的设计与性能分析[J]. 工程设计学报, 2023, 30(2): 262-270.
[2] 张旭,赖磊捷,朱利民. 超精密大行程麦克斯韦磁阻驱动器磁场建模与推力分析[J]. 工程设计学报, 2022, 29(6): 748-756.
[3] 王成军, 李帅. 三关节式软体驱动器的设计及其弯曲性能分析[J]. 工程设计学报, 2021, 28(2): 227-234.
[4] 宋智斌, 胡秀棋. 基于给定非线性刚度的柔顺驱动器设计及性能评估[J]. 工程设计学报, 2020, 27(4): 416-424.
[5] 魏琼, 张永梁, 游颖, 汪泉. 基于多腔软体驱动器的柔性手指设计[J]. 工程设计学报, 2020, 27(4): 425-438.
[6] 李玄, 周双武, 路松, 丁冰晓. 基于二级杠杆机构的二自由度微定位平台设计与分析[J]. 工程设计学报, 2020, 27(4): 533-540.
[7] 孔德帅, 胡高峰, 张冠伟, 张大卫. 压电驱动器可控预紧力主轴设计及性能分析[J]. 工程设计学报, 2019, 26(6): 743-752.
[8] 李达宏, 金樱子, 郭振武, 王斌锐. 新型形状记忆合金驱动器与三指灵巧手设计[J]. 工程设计学报, 2019, 26(5): 506-512.
[9] 隋立明, 席作岩, 刘亭羽. 多腔体式仿生气动软体驱动器的设计与制作[J]. 工程设计学报, 2017, 24(5): 511-517.
[10] 刘凯, 曹毅, 周睿, 丁锐, 葛姝翌. 抗压内LET柔性铰链的建模及分析[J]. 工程设计学报, 2016, 23(6): 585-591.
[11] 胡俊峰,郝亚洲,徐贵阳. 基于有限元法的柔性铰链力学模型和性能分析[J]. 工程设计学报, 2014, 21(5): 432-438.
[12] 刘庆玲. 柔性对称微位移放大机构性能分析方法的研究[J]. 工程设计学报, 2013, 20(4): 344-347.
[13] 杨启志, 姚斌斌, 庄佳奇, 尹小琴. 基于高频柔性并联激振台柔性转动关节的加工误差分析[J]. 工程设计学报, 2012, 19(3): 170-173.
[14] 刘庆玲, 翁海珊, 邱丽. 新型单边复和型柔性铰链的柔度计算及其性能分析[J]. 工程设计学报, 2009, 16(4): 276-280.
[15] 叶 果, 李 威, 王禹桥, 杨雪峰. 直角切口柔性平行四杆机构的输出位移分析[J]. 工程设计学报, 2009, 16(4): 303-307.