Please wait a minute...
工程设计学报
工程设计学报  2012, Vol. 19 Issue (1): 34-38    
工程设计理论、方法与技术     
磁头与离散磁道式磁盘瞬态接触行为研究
 张广玉, 李隆球, 菅翠营, 王林
哈尔滨工业大学 机电工程学院,黑龙江 哈尔滨 150001
Research of transient contact behavior between slider and discrete track recording media
 ZHANG  Guang-Yu, LI  Long-Qiu, JIAN  Cui-Ying, WANG  Lin
School of Mechatronics Engineering, Harbin Institute of Technology, Harbin 150001, China
 全文: PDF(4647 KB)   HTML
摘要： 离散磁道式磁盘在与磁头瞬态接触过程中极易损坏.为改善离散磁道式磁盘的瞬态接触状况,采用有限元仿真方法,建立了平整化前后离散磁道式磁盘与磁头的瞬态接触模型,分析了平整化前后离散磁道式磁盘接触应力分布特点,研究了磁头冲击速度、径向速度、磁盘表面摩擦系数等接触条件及平整化对离散磁道式磁盘最大等效塑性应变、塑性应变总体积的影响.结果表明：磁头冲击速度、寻道速度增大均可导致磁盘最大等效塑性应变、塑性应变总体积增大；摩擦系数增大可增大磁道最大等效塑性应变、减小塑性应变总体积；在接触初期,平整化离散磁道式磁盘可以减小磁道最大接触应力,缓解应力集中现象；在接触全过程中,平整化离散磁道式磁盘可以减小磁道最大等效塑性应变及塑性应变总体积；平整化所用2种弹性模量等力学特性不同的填充材料,即磁道材料与类金刚石碳,对于磁道接触状况的改善作用区别较小.以上结论可为降低离散磁道式磁盘的破坏程度提供理论指导．
关键词： 离散磁道式磁盘;  平整化;  接触应力;  等效塑性应变    
Abstract:  Discrete track recording(DTR) media is prone to be damaged during the transient contact with the slider. In order to improve the transient contact condition of DTR media, a transient slider/DTR media contact model was presented by using finite element method. The distribution characteristics of contact stress field of DTR media were investigated before and after planarization. The effect of contact prerequisites and planarization on the maximum equivalent plastic strain and the total volume of plastic strain was analyzed. The results show that the maximum equivalent plastic strain and the total volume of plastic strain increase with increases of the impact and radial velocity of the slider. It is also found that the maximum equivalent plastic strain increases and the total volume of the plastic strain decreases with an increase of friction coefficient. Planarization can reduce the maximum contact stress of tracks and relieve stress concentration at the beginning of the transient contact process and reduce the maximum equivalent plastic strain and the total volume of plastic strain during the whole process. Filling materials with different elastic modulus in the planarization process, such as magnetic materials and diamond-like-carbon, have little different effect on the improvement of contact conditions of tracks. These conclusions can supply theoretical guidelines for reducing the damage level of DTR media.
Key words: discrete track recording media    planarization    contact stress    equivalent plastic strain
出版日期: 2012-02-15
基金资助:

国家自然科学基金资助项目（51105099）
服务　　
把本文推荐给朋友
加入引用管理器
E-mail Alert
RSS
作者相关文章　　
张广玉
李隆球
菅翠营
王林

引用本文:

张广玉, 李隆球, 菅翠营, 王林. 磁头与离散磁道式磁盘瞬态接触行为研究[J]. 工程设计学报, 2012, 19(1): 34-38.

ZHANG Guang-Yu, LI Long-Qiu, JIAN Cui-Ying, WANG Lin. Research of transient contact behavior between slider and discrete track recording media. Chinese Journal of Engineering Design, 2012, 19(1): 34-38.

链接本文:

https://www.zjujournals.com/gcsjxb/CN/    或    https://www.zjujournals.com/gcsjxb/CN/Y2012/V19/I1/34

[1] 何芝仙, 陈曦, 时培成. 基于动力学分析的大重合度直齿圆柱齿轮强度计算[J]. 工程设计学报, 2020, 27(6): 729-734.
[2] 周镇宇, 唐进元, 董建雄. 同功重比修形斜齿和直齿面齿轮性能对比研究[J]. 工程设计学报, 2016, 23(4): 338-344.
[3] 高创宽, 李 群. 齿面粗糙纹理方向对齿轮润滑效应的影响[J]. 工程设计学报, 2014, 21(4): 393-397.
[4] 黄尚兵, 金光, 安源, 王栋. 滚子摆动从动件盘形凸轮的设计及优化[J]. 工程设计学报, 2012, 19(6): 449-453.
[5] 李立新, 江玉刚, 曹谊勃. 基于精确齿面建模的ZA蜗杆蜗轮有限元接触分析[J]. 工程设计学报, 2011, 18(1): 38-42.