Please wait a minute...
工程设计学报  2012, Vol. 19 Issue (1): 39-42    
工程设计理论、方法与技术     
纵轴式截割头截齿布置对破岩载荷规律的影响
 王 想, 王清峰, 谭正生
中国煤炭科工集团 重庆研究院,重庆400039
The effects of picks arrangement on loads law of rock cutting with longitudinal cutting head
 WANG  Xiang, WANG  Qing-Feng, TAN  Zheng-Sheng
Chongqing Research Institute of China Coal Technology & Engineering Group, Chongqing 400039, China
 全文: PDF(2760 KB)   HTML
摘要: 为了研究截齿布置对纵轴式截割头破岩载荷规律的影响,在建立截割头破岩载荷数学模型的基础上,对3个不同截齿布置参数的截割头破岩载荷进行了仿真,得到了载荷波动曲线及其相关统计量.仿真结果表明载荷存在2个频率的波动:低频波动由螺旋线头数及其包角决定,波动频率等于螺旋线头数与截割头转频的乘积;较高频率的波动由截齿的不连续性引起,波动频率以截割头转频为基频,其大小与截齿周向间隔角有关;同等条件下,随着截齿周向间隔角θi的增加,载荷Ra,Rb,Rc,Mc的峰值和平均值依次增加,但其均方差和波动性系数依次减小.根据仿真结果总结出载荷波动频率的理论计算公式,这对纵轴式截割头的设计研究具有重要的理论指导意义.
关键词: 纵轴式掘进机截割头岩石截割载荷仿真    
Abstract: In order to research the effects of picks arrangement on loads pattern of rock cutting with longitudinal cutting head, loads of three kinds of cutting heads with different pick-arranged were simulated on basis of the mathematical model of rock cutting loads of cutting head, load fluctuation curves and related statistical data were developed. They indicated that the load fluctuates on two frequencies, in which the low-frequency fluctuation is determined by number of helixes and their wrap angle, the value of low-frequency is equal to number of helixes multiplied by rotating frequency of cutting head. On the other hand, the high-frequency fluctuation results from discontinuity of picks, taking the rotating frequency of cutting head as the fundamental frequency.The value of highfrequency is related to circular interval angle of picks. Under the same conditions, average and maximum of Ra,Rb,Rc,Mc increase with θi increase, but mean square deviation and volatility factor of Ra,Rb,Rc,Mc decrease. A theoretical computational formula, which can be used to guide the design of longitudinal cutting head, is developed according to the simulated data.
Key words: longitudinal roadheader    cutting head    rock cutting    load simulation
出版日期: 2012-02-15
基金资助:

中国煤炭科工集团重庆研究院青年创新基金资助项目.

服务  
把本文推荐给朋友
加入引用管理器
E-mail Alert
RSS
作者相关文章  
王想
王清峰
谭正生

引用本文:

王想, 王清峰, 谭正生. 纵轴式截割头截齿布置对破岩载荷规律的影响[J]. 工程设计学报, 2012, 19(1): 39-42.

WANG Xiang, WANG Qing-Feng, TAN Zheng-Sheng. The effects of picks arrangement on loads law of rock cutting with longitudinal cutting head. Chinese Journal of Engineering Design, 2012, 19(1): 39-42.

链接本文:

https://www.zjujournals.com/gcsjxb/CN/        https://www.zjujournals.com/gcsjxb/CN/Y2012/V19/I1/39

[1] 李祥松. TRIZ理论在掘进机截割头设计中的应用[J]. 工程设计学报, 2015, 22(3): 219-223.
[2] 李晓豁, 何洋, 李婷, 杨婷婷. 纵轴式掘进机截割机构纵向随机振动的仿真研究[J]. 工程设计学报, 2013, 20(6): 495-500.