Please wait a minute...
工程设计学报
工程设计学报  2010, Vol. 17 Issue (3): 196-200    
工程设计理论、方法与技术     
水润滑塑料合金轴承设计参数实验分析及优化
 彭晋民, 罗敏峰
福建工程学院 机电及自动化工程系,福建 福州 350108
Experimental analysis and optimization of design parameters on water lubricated plastic alloy bearings
 PENG  Jin-Min, LUO  Min-Feng
Department of Electromechanical and Automation Engineering, Fujian University of Technology, Fuzhou 350108, China
 全文: PDF(742 KB)   HTML
摘要： 国内水润滑轴承设计参数多依据国外产品反求，研究拟通过实验得出各参数的设计准则和轴承的制造工艺.分析了轴瓦结构、长径比等影响水润滑塑料合金轴承润滑特性的设计参数,得到轴承多曲面圆弧凹槽的经验公式和胶层厚度与轴径的关系.通过实验分析了硫化时间、温度和压力等制造工艺参数对轴承材料性能的影响.主要性能包括定伸强度、磨损量和扯断伸长率.综合各实验结果对制造工艺参数进行优化并进行正交实验,得到最优制造工艺.在硫化温度为180 ℃、压力为2 MPa和硫化时间为20 min的条件下制造的长径比为2的水润滑轴承性能可达到或超过美国国防部颁布的MILB17901(船舶)军用标准.
关键词： 水润滑轴承;  成型工艺;  设计参数;  力学性能    
Abstract: Design parameters of water lubricated bearings are always get by reverse from overseas products. Design rules and manufacture process parameters will be obtained from experiments in the research. Design parameters such as bearing structure and long-diameter ratio (L/D) were analyzed, which were the main influence factors for lubrication property of water lubricated bearings. The empirical formula of the multi-curved and circle contacting face of bearings and the relation between the thickness of plastic alloys and the inner diameter of bearings were obtained. And then, the impact of manufacture process parameters including vulcanization time, temperature and pressure on the performance of bearing materials was analyzed through experiments. The main performance included peel strength, tensile strength and wearing capacity. Optimization of manufacture process parameters and the orthogonal experiments on them were carried out by integrating the results of experiments and finally the optimal manufacture process was achieved. The performance of water lubricated bearings with L/D=2 that made on vulcanization temperature 180 ℃, time 20 min and pressure 2 MPa can reach or exceed the standard of MIL-B-17901 (marine) published by USA Ministry of National Defense．
Key words: water lubricated bearings    molding technology    design parameter    mechanic performance
出版日期: 2010-06-28
:  TH 117.21  
基金资助:

福建省自然科学基金资助项目（2008J0179）
服务　　
把本文推荐给朋友
加入引用管理器
E-mail Alert
RSS
作者相关文章　　
彭晋民
罗敏峰

引用本文:

彭晋民, 罗敏峰. 水润滑塑料合金轴承设计参数实验分析及优化[J]. 工程设计学报, 2010, 17(3): 196-200.

PENG Jin-Min, LUO Min-Feng. Experimental analysis and optimization of design parameters on water lubricated plastic alloy bearings[J]. Chinese Journal of Engineering Design, 2010, 17(3): 196-200.

链接本文:

https://www.zjujournals.com/gcsjxb/CN/    或    https://www.zjujournals.com/gcsjxb/CN/Y2010/V17/I3/196

[1] 刘政,王兵振,何改云,张原飞,程绪宇. 极区集成式光伏供电装置结构设计与分析[J]. 工程设计学报, 2022, 29(4): 493-499.
[2] 郑明军, 赵晨磊, 吴文江, 杨摄. 全地形移动机器人车身结构分析与优化[J]. 工程设计学报, 2021, 28(2): 195-202.
[3] 胡俊峰，郝亚洲，徐贵阳. 基于有限元法的柔性铰链力学模型和性能分析[J]. 工程设计学报, 2014, 21(5): 432-438.
[4] 律辉，王优强，刘昺丽，卢宪玖. 不同板条形状对艉轴承的力学性能影响研究及其结构优化[J]. 工程设计学报, 2014, 21(3): 292-300.
[5] 程贤福. 面向可适应性的产品平台设计参数规划方法[J]. 工程设计学报, 2014, 21(2): 140-146.
[6] 陈宝，陈茜，Christian Lohse，雷刚. 基于“双法多程式”的悬架橡胶衬套力学性能估算与试验验证[J]. 工程设计学报, 2014, 21(1): 43-50.
[7] 谭兴强, 贾舒媛, 谢志江. 6_PUS并联机器人动力学性能参数优化设计[J]. 工程设计学报, 2013, 20(6): 470-475.
[8] 方水光, 邵丹璐, 金英连, 王斌锐. 柔性仿人机械臂设计与动力学仿真[J]. 工程设计学报, 2012, 19(4): 307-311.
[9] 潘显钟, 李建勇, 查建中. 基于公理设计理论的FMS优化配置研究[J]. 工程设计学报, 2006, 13(4): 199-204.