Please wait a minute...
工程设计学报
工程设计学报  2021, Vol. 28 Issue (3): 321-328    DOI: 10.3785/j.issn.1006-754X.2021.00.044
保质设计     
考虑压力与温度影响的螺杆马达过盈量设计方法
钟良春1, 况雨春1, 舒峰2, 张聪1
1.西南石油大学 机电工程学院， 四川 成都 610500
2.中建环能科技股份有限公司， 四川 成都 610500
Design method of screw motor interference considering the influence of pressure and temperature
ZHONG Liang-chun1, KUANG Yu-chun1, SHU Feng2, ZHANG Cong1
1.School of Mechatronic Engineering， Southwest Petroleum University， Chengdu 610500， China
2.CSCEC SCIMEE Science & Technology Co.， Ltd.， Chengdu 610500， China
 全文: PDF(2832 KB)   HTML
摘要： 螺杆马达是螺杆钻具的动力源，其定子与转子之间过盈量的合理设计对马达工作性能和使用寿命至关重要。首先，建立了螺杆马达定子与转子的二维啮合有限元模型，并分析了工作压力和井下温度对定子廓形的影响。然后，基于密封性能评价准则，对不同过盈量下定子与转子的接触应力进行计算，并提出定子大、小径处采用不同过盈量的非均匀过盈量设计方法。最后，以螺杆马达转子为基准，设计了考虑压力与温度影响的定子廓线，在理论上实现了定子与转子之间的有效密封和良好接触。螺杆钻具整机台架试验结果表明：相较于传统的过盈量设计方法，考虑压力和温度影响的非均匀过盈量设计方法可使螺杆马达具有更高的效率。研究结果可为螺杆马达过盈量及其余参数的设计提供一定参考。
Abstract: Screw motor is the power source of the screw drilling tool, and the reasonable design of interference between the stator and the rotor is very important for the working performance and service life of the motor. Firstly, a two-dimensional meshing finite element model of the stator and the rotor of the screw motor was established, and the influence of working pressure and bottom hole temperature on the stator profile was analyzed. Then, based on the evaluation criterion of sealing performance, the contact stress of the stator and the rotor under different interference was calculated, and a non-uniform interference design method with different interference at the large and small diameters of the stator was proposed. Finally, based on the rotor of the screw motor, the stator profile considering the influence of pressure and temperature was designed, which theoretically realized the effective sealing and good contact between the stator and the rotor. The bench test results of the screw drilling tool showed that, compared with the common interference design method, the non-uniform interference design method considering the influence of pressure and temperature could make the screw motor have higher efficiency. The research results can provide a certain reference for the design of the interference and other parameters of screw motors.
收稿日期: 2020-08-18 出版日期: 2021-06-28
CLC:  TH 131.7  
基金资助: 国家自然科学基金联合基金资助项目（U19A2097）
通讯作者: 况雨春（1971—），男，四川达州人，教授，博士生导师，博士，从事计算机仿真及CAD/CAE/CFD技术等研究，E-mail：swpikyc@126.com     E-mail: swpikyc@126.com
作者简介: 钟良春（1995—），男，四川内江人，硕士生，从事井下工具研究，E-mail：swpuzlc@qq.com，https：//orcid.org/0000-0001-8615-8041；
服务　　
把本文推荐给朋友
加入引用管理器
E-mail Alert
RSS
作者相关文章　　

引用本文:

钟良春, 况雨春, 舒峰, 张聪. 考虑压力与温度影响的螺杆马达过盈量设计方法[J]. 工程设计学报, 2021, 28(3): 321-328.

ZHONG Liang-chun, KUANG Yu-chun, SHU Feng, ZHANG Cong. Design method of screw motor interference considering the influence of pressure and temperature. Chinese Journal of Engineering Design, 2021, 28(3): 321-328.

链接本文:

https://www.zjujournals.com/gcsjxb/CN/10.3785/j.issn.1006-754X.2021.00.044    或    https://www.zjujournals.com/gcsjxb/CN/Y2021/V28/I3/321

[1] 熊伟, 葛志华, 庞乔, 李曼迪, 王友. 轮毂轴承单元过盈量理论设计及试验研究[J]. 工程设计学报, 2021, 28(1): 41-47.