Please wait a minute...
工程设计学报
工程设计学报  2020, Vol. 27 Issue (2): 223-231    DOI: 10.3785/j.issn.1006-754X.2020.00.021
优化设计     
基于改进有序聚类法的立式加工中心进给系统温测点优化
李传珍, 李国龙, 陶小会, 庞源
重庆大学 机械传动国家重点实验室， 重庆 400044
Optimization of temperature measurement points for feed system of vertical machining center based on improved sequential clustering method
LI Chuan-zhen, LI Guo-long, TAO Xiao-hui, PANG Yuan
State Key Laboratory of Mechanical Transmission, Chongqing University, Chongqing 40044, China
 全文: PDF(1345 KB)   HTML
摘要： 为解决立式加工中心热误差补偿关键技术中温测点难选取的问题，提出了一种基于改进有序聚类法的机床进给系统温测点优化方法。首先，结合试验数据计算反映温测点温度变量与热误差相关性的互信息值，初步筛选机床各部件的温测点，消除测点间的耦合性；然后，根据筛选出的温测点，通过建立类直径矩阵和计算各类的最小误差函数，获得温度变量分类；最后，基于多元线性回归建立包含多个不同温测点的热误差模型，并对模型进行统计学综合分析，确定了最佳聚类数和最佳温测点。结果表明：在不同加工条件下采用改进有序聚类法建立的热误差模型的均方根误差和平均残差分别降至1.05 μm和1 μm以下，相较于采用传统有序聚类法和灰色关联度模糊聚类法建立的热误差模型，它具有更高的热误差预测精度和更好的鲁棒性。所提方法在中小型加工中心进给系统的温测点研究中具有广阔的应用前景。
关键词： 立式加工中心;  改进有序聚类法;  统计学分析;  测点优化;  热误差建模    
Abstract: To solve the problem that the key technology of thermal error compensation in vertical machining center is difficult to select the temperature measurement point, a new method based on improved sequential clustering method is proposed to optimize the temperature measurement points for feed system of the machine tools. First of all, basing on experimental data, the mutual information value reflecting the correlation between temperature variables and thermal errors was calculated to select temperature measurement points of each component preliminarily and reduce coupling between measurement points. Then, according to the selected temperature measurement points, the temperature variables were classified by establishing the class diameter matrix and calculating the minimum error function. After that, basing on multiple linear regression, a thermal error model containing several different measurement points was established and statistical comprehensive analysis was conducted on the models, so the optimal clustering number and optimal temperature measurement points were determined. Results showed that the root mean square error and average residual of the thermal error model established by improved sequential clustering method could be reduced to less than 1 μm and 1.05 μm respectively under different processing conditions. Compared with the thermal error model established by the unmodified sequential clustering method and the grey relational degree fuzzy clustering method, this thermal error prediction model had higher prediction accuracy and better robustness. This method has a broad application prospect in the research of temperature measurement point for medium and small machining center feed system.
Key words: vertical machining center    improved sequential clustering method    statistical analysis    optimization of measurement points    thermal error modeling
收稿日期: 2019-08-16 出版日期: 2020-04-28
CLC:  TG 502.15  
基金资助: 国家自然科学基金资助项目(51875066)；重庆市科技计划项目(cstc2018jszx-cyzdX0119)
通讯作者: 李国龙（1969—），男，重庆人，教授，博士生导师，博士，从事智能数控技术和系统、精密制齿技术和装备等研究，E-mail:glli@cqu.edu.cn   
作者简介: 李传珍（1996—），女，重庆人，硕士生，从事智能数控技术和系统开发研究，E-mail:370080865@qq.com，https://orcid.org/0000-0002-5888-721X
服务　　
把本文推荐给朋友
加入引用管理器
E-mail Alert
RSS
作者相关文章　　
李传珍
李国龙
陶小会
庞源

引用本文:

李传珍, 李国龙, 陶小会, 庞源. 基于改进有序聚类法的立式加工中心进给系统温测点优化[J]. 工程设计学报, 2020, 27(2): 223-231.

LI Chuan-zhen, LI Guo-long, TAO Xiao-hui, PANG Yuan. Optimization of temperature measurement points for feed system of vertical machining center based on improved sequential clustering method. Chinese Journal of Engineering Design, 2020, 27(2): 223-231.

链接本文:

https://www.zjujournals.com/gcsjxb/CN/10.3785/j.issn.1006-754X.2020.00.021    或    https://www.zjujournals.com/gcsjxb/CN/Y2020/V27/I2/223

[1] ZHOUD Z, GUIL, TANY G, et al. Actualities and development of heavy-duty CNC machine tool thermal error monitoring technology[J]. Chinese Journal of Mechanical Engineering, 2017, 30(5): 1262-1281. doi: 10.1007/s10033-017-0166-5
[2] 王海同,李铁民,王立平,等. 机床热误差建模研究综述[J]. 机械工程学报,2015,51(9):119-128. doi: 10.3901/JME.2015.09. 119 WANGHai-tong, LITie-min, WANGLi-ping, et al. Review on thermal error modeling of machine tools[J]. Journal of Mechanical Engineering, 2015, 51(9): 119-128.
[3] MAYRJ, JEDRZEJEWSKIJ, UHLMANNE, et al. Thermal issues in machine tools[J]. CIRP Annals-Manufacturing Technology, 2012, 61(2): 771-780. doi: 10.1016/j.cirp.2012.05. 008
[4] LIUM Y, ZHOUW J, SONGH, et al. Study of the temperature distribution of a machine tool spindle bearing based on FBG quasi-distributed sensing[J]. The International Journal of Advanced Manufacturing Technology, 2018, 98(1/4): 263-274. doi: 10.1007/s00170-018-2215-3
[5] LIY, ZHAOJ, JIS. Thermal positioning error modeling of machine tools using a bat algorithm-based back propagation neural network[J]. The International Journal of Advanced Manufacturing Technology, 2018, 97(6/8): 2575-2586. doi: 10. 1007/s00170-018-1978-x
[6] MAC, ZHAOL, MEIX S, et al. Thermal error compensation of high-speed spindle system based on a modified BP neural network[J]. The International Journal of Advanced Manufacturing Technology, 2017, 89(9/12): 3071-3085. doi: 10. 1007/s00170-016-9254-4
[7] 朱小龙,杨建国,代贵松. 基于AVQ聚类和OIF-Elman神经网络的机床热误差建模[J]. 上海交通大学学报,2014, 48(1):16-21. doi: 10.16183/j.cnki.jsjtu.2014.01.004 ZHUXiao-long, YANGJian-guo, DAIGui-song. AVQ clustering algorithm and OIF-Elman neural network for machine tool thermal error[J]. Journal of Shanghai Jiaotong University, 2014, 48(1): 16-21.
[8] WANGH T, WANGL P, LIT M. Thermal sensor selection for the thermal error modeling of machine tool based on the fuzzy clustering method[J]. International Journal of Advanced Manufacturing Technology, 2013, 69(1/4): 121-126. doi: 10. 1007/s00170-013-4998-6
[9] 张伟,叶文华. 基于灰色关联和模糊聚类的机床温度测点优化[J]. 中国机械工程,2014,25(4):456-460. doi: 10.3969/j. issn.1004-132X.2014.04.006 ZHANGWei, YEWen-hua. Optimization of temperature measuring points for machine tools based on grey correlation and fuzzy clustering analysis[J]. China Mechanical Engineering，2014, 25(4): 456-460.
[10] MIAOE M, GONGY, DANGL C, et al. Temperature-sensitive point selection of thermal error model of CNC machining center[J]. International Journal of Advanced Manufacturing Technology, 2014, 74(5/8): 681-691. doi: 10. 1007/s00170-014-6009-y
[11] 丛明,李泳耀,孙宗余,等. 机床温度测点优化方法研究及试验验证[J]. 大连理工大学学报,2015,55(6):582-588. doi: 10.7511/dllgxb201506004 CONGMing, LIYong-yao, SUNZong-yu, et al. An optimization method of temperature measuring points for machine tools and experimental verification[J]. Journal of Dalian University of Technology, 2015, 55 (6): 582-588.
[12] 李艳,李英浩,高峰,等. 基于互信息法和改进模糊聚类的温度测点优化[J]. 仪器仪表学报,2015,36(11):2466-2472. doi: 10.3969/j.issn.0254-3087.2015.11.009 LIYan, LIYing-hao, GAOFeng, et al. Investigation on optimization of temperature measurement key points based on mutual information method and improved fuzzy clustering analysis[J]. Chinese Journal of Scientific Instrument, 2015, 36 (11): 2466-2472.
[13] 李逢春,王海同,李铁民. 重型数控机床热误差建模及预测方法的研究[J]. 机械工程学报,2016,52(11):154-160. doi: 10.3901/JME.2016.11.154 LIFeng-chun, WANGHai-tong, LITie-min. Research on thermal error modeling and prediction methods for heavy NC machine tools [J]. Journal of Mechanical Engineering, 2016, 52(11): 154-160.
[14] 魏弦,高峰,李艳,等. 龙门机床进给系统热误差模型关键点优化[J]. 仪器仪表学报,2016,37(6):1340-1346. doi: 10. 3969/j.issn.0254-3087.2016.06.018 WEIXian, GAOFeng, LIYan, et al. Optimization of thermal error model critical point for gantry machine tool feeding system [J]. Chinese Journal of Scientific Instrument, 2016, 37 (6): 1340-1346.doi:10.3969/j.issn.0254-3087.2016.06.018
[15] 高峰,刘江,杨新刚,等. 基于Fisher最优分割法的机床热关键点优化研究[J]. 仪器仪表学报,2013,34(5):1070-1075. doi: 10.3969/j.issn.0254-3087.2013.05.017 GAOFeng, LIUJiang, YANGXin-gang, et al. Study on optimization of thermal key points for machine tools based on Fisher optimal segmentation method[J]. Chinese Journal of Scientific Instrument, 2013, 34 (5): 1070-1075.
[16] YANGJ, MEIX S, FENGB, et al. Experiments and simulation of thermal behaviors of the dual-drive servo feed system[J]. Chinese Journal of Mechanical Engineering, 2015, 28(1): 76-87. doi: 10.3901/CJME.2014.1031.162
[17] 纪学军. 数控机床热误差建模及补偿研究[J]. 制造技术与机床,2017(12):115-120. doi: 10.19287/j.cnki.1005-2402. 2017.12.020 JIXue-jun. Research on thermal error modeling and compensation of CNC machine tool[J]. Manufacturing Technology and Machine Tool, 2017 (12): 115-120.
[18] 刘阔,孙名佳,吴玉亮, 等. 无温度传感器的数控机床进给轴热误差补偿[J]. 机械工程学报,2016,52(15):162-169. doi: 10.3901/JME.2016.15.162 LIUKuo, SUNMing-jia, WUYu-liang, et al. Thermal error compensation without temperature sensors for CNC machine tools’ feed drive system[J]. Journal of Mechanical Engineering, 2016, 52(15): 162-169.
[19] 孙志超,侯瑞生,陶涛,等. 数控车床综合热误差建模及工程应用[J]. 哈尔滨工业大学学报,2016,48(1):107-113. doi: 10.11918/j.issn.0367-6234.2016.01.016 SUNZhi-chao, HOURui-sheng, TAOTao, et al. Comprehensive thermal error modeling for NC lathe in engineering application[J]. Journal of Harbin Institute of Technology, 2016, 48(1): 107-113.
No related articles found!