Please wait a minute...
工程设计学报
工程设计学报  2020, Vol. 27 Issue (1): 111-120    DOI: 10.3785/j.issn.1006-754X.2020.00.005
建模、仿真、分析与决策     
蜗杆砂轮磨齿机几何误差敏感度分析
陶小会, 李国龙, 徐凯, 李传珍
重庆大学 机械传动国家重点实验室，重庆400044
Sensitivity analysis of geometric error of worm wheel gear grinding machine
TAO Xiao-hui, LI Guo-long, XU Kai, LI Chuan-zhen
State Key Laboratory of Mechanical Transmission, Chongqing University,Chongqing400044,China
 全文: PDF(2001 KB)   HTML
摘要： 为识别影响蜗杆砂轮磨齿机空间精度的关键几何误差项，提出一种基于旋量理论和Sobol法的几何误差敏感度分析方法。以YW7232型蜗杆砂轮磨齿机为研究对象，首先，基于旋量理论建立机床的几何误差模型；然后，采用Sobol法计算机床磨削过程中各几何误差项对空间误差分量的敏感度系数，并识别出关键几何误差项；最后，对机床的关键几何误差项进行修正，通过仿真分析对比修正前后机床的空间误差分量以及3种测量模式下球杆仪的杆长。仿真结果表明所提出的方法可有效识别出机床磨削过程中的关键几何误差，这可为提高机床精度提供理论指导。
Abstract: To identify the key geometric error terms which affect the space precision of the worm wheel gear grinding machine, a geometric error sensitivity analysis method based on the screw theory and Sobol method is proposed. The YW7232 worm wheel gear grinding machine was taken as the research object. Firstly, the geometric error model of the machine tool was established based on the screw theory. Then, the sensitivity coefficient of each geometric error term to the spatial error component of the machine tool during the grinding process was calculated by using Sobol method and the key geometric error terms were identified. Finally, after correcting the key geometric error terms of the machine tool， the spatial error component of the machine tool before and after correction and the rod length of the ballbar in the three measurement modes were compared by simulation analysis. The simulation results show that the proposed method can effectively identify the key geometric errors in the grinding process of the machine tool， and provide theoretical guidance for improving the precision of the machine tool.
收稿日期: 2019-08-15 出版日期: 2020-02-28
CLC:  TH 161  
基金资助: 国家自然科学基金资助项目（51875066）
通讯作者: 李国龙(1969—),男,重庆人，教授，博士生导师，博士，从事精密制造与装备研究，E-mail:glli@cqu.edu.cn     E-mail: glli@cqu.edu.cn
作者简介: 陶小会（1996—），女，湖北襄阳人，硕士生，从事机床几何误差测量与补偿研究，E-mail:taoxiaohui96@163.com, https://orcid.org/0000-0002-4389-3270
服务　　
把本文推荐给朋友
加入引用管理器
E-mail Alert
RSS
作者相关文章　　

引用本文:

陶小会, 李国龙, 徐凯, 李传珍. 蜗杆砂轮磨齿机几何误差敏感度分析[J]. 工程设计学报, 2020, 27(1): 111-120.

TAO Xiao-hui, LI Guo-long, XU Kai, LI Chuan-zhen. Sensitivity analysis of geometric error of worm wheel gear grinding machine. Chinese Journal of Engineering Design, 2020, 27(1): 111-120.

链接本文:

https://www.zjujournals.com/gcsjxb/CN/10.3785/j.issn.1006-754X.2020.00.005    或    https://www.zjujournals.com/gcsjxb/CN/Y2020/V27/I1/111

[1] 刘洪江,胡腾,何勇,董峰,罗为. 基于CSO-SVM的数控机床主轴热误差建模[J]. 工程设计学报, 2022, 29(3): 339-346.
[2] 付扬, 李国龙, 徐凯, 唐晓东. 基于多源融合理论的机床圆度误差测量不确定度评定[J]. 工程设计学报, 2021, 28(3): 278-286.
[3] 王友利, 刘飞, 董洪全, 王晓慧. 基于功能尺寸最短路径的零件尺寸标注模式的设计[J]. 工程设计学报, 2021, 28(2): 141-147.
[4] 陈洋, 任成祖, 邓晓帆, 陈光, 靳新民. 基于双盘直槽研磨的圆柱滚子自转运动研究[J]. 工程设计学报, 2021, 28(2): 179-189.
[5] 邓晓帆, 任成祖, 陈洋, 陈光, 蔡智杰, 贺英伦. 基于摩擦磨损实验的双盘直槽研磨方法的研具选材研究[J]. 工程设计学报, 2020, 27(6): 720-728.