|
|
|
| Fatigue life test analysis of sliding framework under clearance impact load of plough |
| MAO Jun1, ZHANG Yu1, LIU Zhan-sheng2, LI Guo-ping3, CHEN Hong-yue1 |
1. College of Mechanical Engineering, Liaoning Technical University, Fuxin 123000, China;
2. China National Coal Mining Equipment Co., Ltd., Beijing 100011, China;
3. China Coal Zhangjiakou Coal Mining Machinery Co., Ltd., Zhangjiakou 076250, China |
|
|
|
Abstract To solve the fatigue break phenomenon on the middle part of sliding framework of coal planer happened during the working process, the 3-DOF crash dynamic model of plough was established based on the Winkler model by combining theory and experiment together. Test criterion of contact-impact between plow head and sliding framework was established by the collision detection method of the arithmetic of the distance between a point and a line. The maximum impact forces of plow head and sliding framework on each point were obtained by numerical methods,and were used as the load of fatigue test. The fatigue test of middle trough sliding framework was executed. Fatigue life of sliding framework was obtained. The results showed that initial crack appeared at the forepart of standing plate when sliding framework was under the maximum impact force and the failure point tended to appear at the bottom of standing plate when static strength became invalid. The results provide theoretical basis for the improvement of fatigue strength of sliding framework.
|
|
Received: 03 July 2015
Published: 28 April 2016
|
|
|
刨头间隙碰撞载荷下滑架体疲劳寿命试验分析
针对刨煤机中部槽滑架体在工作过程中出现的疲劳断裂现象,采用理论与试验相结合的方法,基于Winkler弹性地基接触模型,建立了刨头三自由度碰撞振动动力学模型.通过点到直线的距离算法作为检验碰撞的准则,构造了刨头与滑架接触碰撞判别条件.采用数值方法进行求解,得到刨头与滑架各点的最大碰撞力,并以此作为疲劳试验载荷,对中部槽滑架体进行疲劳寿命试验,得到了滑架体的疲劳寿命.研究结果表明:滑架体在最大碰撞力作用下,在立板前端产生初始裂纹,在发生静强度失效时,失效点倾向于立板后部下端.研究结果对提高滑架体疲劳强度提供了理论依据.
关键词：
刨煤机,
接触碰撞,
滑架体,
疲劳断裂
|
|
| [1] 赵丽娟,孙中刚,李国平.刨煤机牵引块可靠性分析及疲劳寿命预测[J].煤炭学报,2012,37 (3):516-520. ZHAO LI-juan,SUN Zhong-gang,LI Guo-ping.Plow traction block reliability analysis and fatigue life prediction[J].Journal of China Coal Society,2012,37 (3):516-520.[2] 赵丽娟,刘旭南,张建军,等.刨煤机刨链回转接头的可靠性[J].机械设计与研究,2013,29 (3):118-122. ZHAO Li-juan,LIU Xu-nan,ZHANG Jian-jun,et al.Reliability analysis of plow chain swivel joint based on virtual prototyping[M].Machine Design and Research,2013,29 (3):118-122.[3] 赵丽娟,马联伟,刘旭南,等.难刨煤层刨刀可靠性与疲劳寿命研究[J].机械设计,2013,30 (4):85-88. ZHAO Li-juan,MA Lian-wei,LIU Xu-nan,et al.Plow bit reliability and fatigue life analysis in hard cutting seam[J].Journal of Machine Design,2013,30 (4):85-88.[4] 康晓敏,李贵轩.随机动载荷作用下刨煤机刨链疲劳寿命预测[J].煤炭学报,2010,35 (3):503-507. KANG Xiao-min,LI Gui-xuan.Prediction of fatigue life of coa1 plow chain under stochastic dynamic load[J].Journal of China coal Society,2010,35 (3):503-507.[5] 康晓敏,李贵轩.刨煤机刨头的稳定性分析[J].中国机械工程,2012,23 (22):2739-2742. KANG Xiao-min,LI Gui-xuan.Stability analysis of plow body of coal plow[J].China Mechanical Engineering,2012,23 (22):2739-2742.[6] 卢绪祥,刘正强,黄树红,等.含间隙碰撞振动系统的非线性振动特性[J].动力工程学报,2012,32 (5):388-393. LU Xu-xiang,LIU Zheng-qiang,HUANG Shu-hong,et al.Nonlinear vibration characteristics of a vibro-impact system with clearance[J].Journal of Chinese Society of Power Engineering,2012,32 (5):388-393.[7] PASHAH S,MASSENZIO M,JACQUELIN E. Prediction of structural response for low velocity impact[J].International Journal of Impact Engineering,2008,35(2):119-132.[8] BAPAT C N.The general motion of an inclined impact damper with friction[J].Journal of Sound Vibration,1995,184(11):417-427.[9] AHN Kil-young,RYU Bong-jo.A modeling of impact dynamics and its application to impact force prediction[J].Journal of Mechanical Science and Technology,2005,19(1):422-428.[10] FLORES P,AMBROSIO J,CLARO J C P,et al.Influence of the contact impact force model on the dynamic response of multibody systems [J].Proceedings of the Institution of Mechanical Engineers,Part K:Journal of Multi-body Dynamics,2006,220(1):21-34.[11] GERASIMOV S A.Vibration-impact dynamics [J].Russian Engineering Research,2013,33(3):130-132.[12] PAULO Flores,JORGE Ambrósio.On the contact detection for contact-impact analysis in multibody systems[J].Multibody System Dynamics,2010,24(1):103-122.[13] FLORES P J,AMBROSIO J C,PIMENTA Claro.Contact-impact force models for mechanical systems[J].Kinematics and Dynamics of Multibody Systems with Imperfect Joints,2008,12(34):47-66.[14] 李晓豁,付伟丽,张飞虎,等.刨头上不同位置刨刀的随机载荷模拟研究[J].微计算机信息,2011,27 (12):24-26. LI Xiao-huo,FU Wei-li,ZHANG Fei-hu,et al.Simulation and study of random loads on plow tools at different locations of plough head[J].Microcomputer Information,2011,27(12):24-26.[15] 刘中华,尹晓春.钝圆头质量对简支梁的多次弹塑性撞击[J].爆炸与冲击,2010,30(2):138-144. LIU Zhong-hua,YIN Xiao-chun.Multiple elastic-plastic impacts of a simple supported beam struck by around-nosed mass[J].Explosion and Shock Waves,2010,30(2):138-144. |
|
Viewed |
|
|
|
Full text
|
|
|
|
|
Abstract
|
|
|
|
|
Cited |
|
|
|
|
| |
Shared |
|
|
|
|
| |
Discussed |
|
|
|
|
