Please wait a minute...
工程设计学报
工程设计学报  2009, Vol. 16 Issue (6): 444-446    
工程设计理论、方法与技术     
基于权因子的三次NURBS曲线推拉方法
 骆勇骏, 叶邦彦
华南理工大学 机械与车辆工程学院, 广东 广州 510640
Distorting method for cubic NURBS based on weights
 LUO  Yong-Jun, YE  Bang-Yan
School of Mechanical and Automotive Engineering, South China University of Technology, Guangzhou 510640, China
 全文: PDF(2728 KB)   HTML
摘要： 总结了更改1个或2个相邻权因子对NURBS曲线形状影响的一般规律,及根据新NURBS曲线形状来确定权因子的计算公式.在对前人研究成果的深入分析下,笔者发现并证明了通过权因子来使三次NURBS曲线朝任意方向推拉的有关性质,并提出根据修改后的三次NURBS曲线特征点的变化来推算相应1个或2个相邻权因子的计算方法.在针对指向非控制点方向的三次NURBS曲线推拉中,采用直接搜索法得出新曲线相邻两权因子的比值后根据权因子计算公式确定权因子.最后通过实例分析证明了所提出的方法与计算公式与实际相符.
关键词： 非均匀有理B样条;  权因子;  基函数;  曲线推拉变形    
Abstract: The general law of the impact of changes in one weight or two neighboring weights on the shape of NURBS curve was summarized as well as the law of determining weights according to the shape of NURBS curve. Based on the existing research achievements, the characteristics of distorting the NUBRS curve to random directions by weights were discovered and proved. Furthermore, the calculation method of the corresponding weights or two neighboring weights according to the changes of the feature points on the revised cubic NUBRS curve was proposed too. In the situation of distorting cubic NURBS at the direction of non-controlling point, firstly, the ratio of the new curve's two neighboring weights was obtained by directly searching method, and then the weights were determined according to the weight calculation formula. Finally, examples were used to demonstrate that the proposed method agree with the reality well.
Key words:  NURBS    weight    base function    shape of distorting curve
出版日期: 2009-12-28
:  TP 391  
服务　　
把本文推荐给朋友
加入引用管理器
E-mail Alert
RSS
作者相关文章　　
骆勇骏
叶邦彦

引用本文:

骆勇骏, 叶邦彦. 基于权因子的三次NURBS曲线推拉方法[J]. 工程设计学报, 2009, 16(6): 444-446.

LUO Yong-Jun, YE Bang-Yan. Distorting method for cubic NURBS based on weights[J]. Chinese Journal of Engineering Design, 2009, 16(6): 444-446.

链接本文:

https://www.zjujournals.com/gcsjxb/CN/    或    https://www.zjujournals.com/gcsjxb/CN/Y2009/V16/I6/444

[1] 李琴,贾英崎,黄玉峰,李刚,叶闯. 一种工业机器人多目标轨迹优化算法[J]. 工程设计学报, 2022, 29(2): 187-195.
[2] 窦毅芳, 刘飞, 张为华. 响应面建模方法的比较分析[J]. 工程设计学报, 2007, 14(5): 359-363.