Please wait a minute...
工程设计学报
工程设计学报  2009, Vol. 16 Issue (3): 200-204    
工程设计理论、方法与技术     
具有开槽结构的大尺寸立方形超声塑料焊接焊头的设计
 梁召峰1，2，3, 周光平1, 莫喜平2, 李正中1
1.深圳职业技术学院 电子工程系,广东 深圳 518055； 2. 中国科学院 声学研究所,北京 100080;
3. 中国科学院 研究生院,北京 100080
Design of large cross-section block horns with slots for ultrasonic plastic welding
 LIANG  Zhao-Feng1，2，3, ZHOU  Guang-Ping1, MO  Xi-Ping2, LI  Zheng-Zhong1
1. Department of Electronic Engineering, Shenzhen Polytechnic, Shenzhen 518055, China;
2. Institute of Acoustics, Chinese Academy of Sciences, Beijing 100080, China;
3. Graduate School of the Chinese Academy of Sciences, Beijing 100080, China
 全文: PDF(358 KB)   HTML
摘要： 提出一种具有开槽结构的大尺寸立方形超声塑料焊接焊头的设计方法,并对其进行了实验验证.首先通过合理开槽将大尺寸立方形焊头划分为若干单元,然后将各焊头单元和立方形半波振子比较,利用等效机械阻抗的概念得出焊头单元的频率方程,其间考虑了耦合振动的影响.最后利用该方程研究了开槽数、槽宽度以及槽长度等因素对焊头振动特性的影响.按此方法设计加工了几组具有开槽结构的大尺寸立方形焊头,结果表明焊头谐振频率的实测值和理论值吻合得很好.
关键词： 立方形焊头;  超声塑料焊接;  开槽;  频率方程;  耦合振动    
Abstract: A new design method for large cross-section ultrasonic plastic welding block horns with slots was presented and experimental validation on it was carried out. Firstly, the block horns are reasonably divided into some units, and then these units were compared with half wavelength block resonator with constant cross-section. By adopting the concept of equivalent mechanical impedance, the frequency equation of the mentioned horn element unit was obtained and meanwhile the influence of coupled vibration was taken into account. Finally, by utilizing this equation, the influence of the number of slots, their width and length on vibrating characteristics of horn were analyzed. In light of this design method, several groups of the target block horns are manufactured and the results indicate that the resonant frequency well agrees with the theoretic one.
Key words: block horn    ultrasonic plastic welding    slot    frequency equation    coupled vibration
出版日期: 2009-06-28
基金资助:

国家自然科学基金资助项目（10574094）；广东省自然科学基金资助项目（07009027）
服务　　
把本文推荐给朋友
加入引用管理器
E-mail Alert
RSS
作者相关文章　　
梁召峰
周光平
莫喜平
李正中

引用本文:

梁召峰, 周光平, 莫喜平, 李正中. 具有开槽结构的大尺寸立方形超声塑料焊接焊头的设计[J]. 工程设计学报, 2009, 16(3): 200-204.

LIANG Zhao-Feng, ZHOU Guang-Ping, MO Xi-Ping, LI Zheng-Zhong. Design of large cross-section block horns with slots for ultrasonic plastic welding[J]. Chinese Journal of Engineering Design, 2009, 16(3): 200-204.

链接本文:

https://www.zjujournals.com/gcsjxb/CN/    或    https://www.zjujournals.com/gcsjxb/CN/Y2009/V16/I3/200

[1] 马彪,秦慧斌,冯毅,白旭日,辛佳毅. 旋转超声内圆磨削砂轮变幅器的设计与试验研究[J]. 工程设计学报, 2023, 30(1): 117-126.
[2] 付俊帆, 秦慧斌, 吕明. 多环盘组合结构的横向弯曲耦合振动建模与求解[J]. 工程设计学报, 2017, 24(3): 295-302.
[3] 姚涛, 段国林, 蔡瑾, 张家谔. 开槽填充黏弹性材料对圆锯片振动的影响分析[J]. 工程设计学报, 2010, 17(5): 355-359.