Please wait a minute...
工程设计学报
工程设计学报  2011, Vol. 18 Issue (6): 428-436    
工程设计理论、方法与技术     
散状物料转载系统设计DEM仿真方法的研究
 宋伟刚, 王天夫
东北大学 机械工程与自动化学院，辽宁 沈阳 110004
The research on DEM method to design bulk material transfer system
 SONG  Wei-Gang, WANG  Tian-Fu
School of Mechanical Engineering and Automation， Northeastern University， Shenyang 110004，  China
 全文: PDF(3715 KB)   HTML
摘要： 颗粒仿真技术可以对散状物料的运动进行观察、机理分析、受力分析、磨损(寿命)估计和系统优化.比较了散状物料转载计算方法，给出了采用DEM方法的建模与模型检验的基本步骤.针对DEM计算方法存在所需计算时间过长的问题，实验比较了降低剪切模量和增大颗粒粒度等方法对DEM计算时间和实验结果的影响，结果表明，在不影响计算结果的前提下可通过降低剪切模量和增大颗粒粒度来缩短DEM仿真计算时间.利用EDEM软件实现了散料转载过程的可视化，比较分析了直线型溜槽、折线型溜槽和曲线型溜槽中物料转载效果.仿真表明：采用变曲率半径效果更好；U型溜槽截面能够减少物料不对中情况的发生.
关键词： 带式输送机;  散料转载;  离散单元方法;  溜槽    
Abstract: Particulate material simulation technology can observe the motion condition of the bulk material， analyze the material's motion mechanism and the forces which act on the materials， it also can estimate the wear condition which means the remaining useful life. Besides， it can optimize the transfer system. Different calculation methods of bulk material transfer were compared; the steps of modeling and model checking using Discrete Element Method (DEM) method were built. Due to the problem of excessive computation time required by DEM calculations， the discrete element simulation was carried on in the condition of reducing shear modulus and increasing particle size. After comparing the experimental results and computing time of DEM with normal condition， it shows that the methods of reducing shear modulus and increasing particle size can reduce the time of DEM simulation on the premise of having no affection on the result. A simulation model established in EDEM software realized the visualization of material flow in transfer process. The effects of the material transfer in the straight line chute， polyline chute and the curved line chute are compared. Simulation results show that variable radius is better for material transfer and “U” type chute cross-section can reduce the misalignments in transferring the bulk material．
Key words: belt conveyor    bulk material transfer    DEM    chute
出版日期: 2011-12-28
:  TH 222  
基金资助:

国家自然科学基金资助项目(50775031)
服务　　
把本文推荐给朋友
加入引用管理器
E-mail Alert
RSS
作者相关文章　　
宋伟刚
王天夫

引用本文:

宋伟刚, 王天夫. 散状物料转载系统设计DEM仿真方法的研究[J]. 工程设计学报, 2011, 18(6): 428-436.

SONG Wei-Gang, WANG Tian-Fu. The research on DEM method to design bulk material transfer system[J]. Chinese Journal of Engineering Design, 2011, 18(6): 428-436.

链接本文:

https://www.zjujournals.com/gcsjxb/CN/    或    https://www.zjujournals.com/gcsjxb/CN/Y2011/V18/I6/428

[1] 宋伟刚, 季洪博. 圆管带式输送机的研究进展及其设计计算方法[J]. 工程设计学报, 2018, 25(1): 1-11.
[2] 王尧, 李淑君, 赵文玉, 孟文俊. 带式输送机用直线电机静动态特性试验与分析[J]. 工程设计学报, 2017, 24(3): 303-310.
[3] 宋伟刚, 姜 涛. 带式输送机功率计算方法及其工程应用问题的研究[J]. 工程设计学报, 2008, 15(6): 448-456.
[4] 王丹, 宋伟刚. 平面转弯带式输送机启动过程计算机仿真[J]. 工程设计学报, 2005, 12(1): 28-34.
[5] 宋伟刚, 战欣, 王元元. 大型带式输送机驱动装置的比较研究[J]. 工程设计学报, 2004, 11(6): 301-311.