Please wait a minute...
工程设计学报
工程设计学报  2011, Vol. 18 Issue (6): 423-427    
工程设计理论、方法与技术     
基于拉弯比的焊缝名义应力的提取
 阳光武1, 赵科2, 肖守讷1, 张卫华1
1.西南交通大学 牵引动力国家重点实验室，四川 成都 610031; 2.河南工程学院 机械工程系，河南 郑州 451191
Nominal stress extraction of weld based on ratio of tension and bending
 YANG  Guang-Wu1, ZHAO  Ke2, XIAO  Shou-Ne1, ZHANG  Wei-Hua1
1.State Key Laboratory of Traction Power， Southwest Jiaotong University， Chengdu  610031， China;
2. Department of Mechanical Engineering, Henan College of Engineering, Zhengzhou 451191, China
 全文: PDF(934 KB)   HTML
摘要： 为了获得任意拉弯组合载荷下焊缝的名义应力，利用纯弯和纯拉压载荷下的应力集中系数，引入拉弯组合名义应力换算系数，将基于纯拉压名义应力的焊缝疲劳性能数据，转换为疲劳损伤一致的、基于拉弯组合名义应力的焊缝疲劳性能数据．为了消除有限元建模导致的计算误差，引入单元尺寸影响因子，将拉弯组合的计算应力转换为拉弯组合的名义应力．通过上面2个转换，引入拉弯组合计算名义应力换算系数，将有限元中的拉弯组合计算应力转换为基于拉压载荷疲劳试验的名义应力，从而在具体的焊缝结构疲劳强度评估时可以直接使用拉压载荷下的疲劳试验数据．计算结果表明：拉弯组合计算名义应力换算系数与拉弯比、拉弯应力集中因子比和有限元模型中拉弯单元尺寸影响因子有关．通过选择合适的单元尺寸，使得拉压单元尺寸影响因子等于拉弯应力集中因子比，且弯曲单元尺寸影响因子等于1，可使得拉弯组合计算名义应力换算系数恒等于拉压单元尺寸影响因子，而与拉弯比无关．
关键词： 疲劳强度;  焊缝;  拉弯比;  名义应力    
Abstract: In order to obtain nominal stress of weld under arbitrary combination of tension and bending load， stress and strain transformation coefficient of combined nominal stress of tension and bending was introduced， and fatigue data of weld based on pure tension nominal stress was transformed to that based on combined nominal stress of tension and bending with the same damage by means of stress concentration factor of tension and bending. Combined calculation stress of tension and bending was transformed to combined nominal stress by introducing element size effect factor to eliminate stress concentration in finite element model of weld. With the above transformations， transformation coefficient of combined calculation nominal stress of tension and bending was introduced， and combined calculation stress of tension and bending was transformed to the nominal stress based on pure tension load test so that the fatigue data of weld based on pure tension nominal stress could be used to evaluate welded structure directly. Calculation results show that transformation coefficient of combined calculation nominal stress of tension and bending is related to ratio of tension and bending， ratio of stress concentration factor of tension and bending， and element size effect factor of tension and bending caused by finite element modeling. Proper selection of element size will make the element size effect factor of tension equal to the ratio of stress concentration factor of tension and bending and the element size effect factor of bending equal to one， which makes the transformation coefficient of combined calculation nominal stress of tension and bending be identical to the element size effect factor of tension and independent to ratio of tension and bending.
Key words: fatigue strength    weld    ratio of tension and bending    nominal stress
出版日期: 2011-12-28
:  TH 140.1  
基金资助:

国家重点基础研究发展计划（973计划）资助项目(2007cb714700)；四川省科技计划项目（2011JY0029）
服务　　
把本文推荐给朋友
加入引用管理器
E-mail Alert
RSS
作者相关文章　　
阳光武
赵科
肖守讷
张卫华

引用本文:

阳光武, 赵科, 肖守讷, 张卫华. 基于拉弯比的焊缝名义应力的提取[J]. 工程设计学报, 2011, 18(6): 423-427.

YANG Guang-Wu, ZHAO Ke, XIAO Shou-Ne, ZHANG Wei-Hua. Nominal stress extraction of weld based on ratio of tension and bending[J]. Chinese Journal of Engineering Design, 2011, 18(6): 423-427.

链接本文:

https://www.zjujournals.com/gcsjxb/CN/    或    https://www.zjujournals.com/gcsjxb/CN/Y2011/V18/I6/423

[1] 张佳,周兆明,练章华,李锴,陈智. 乏燃料水池覆面板对接焊缝裂纹检测研究[J]. 工程设计学报, 2023, 30(3): 372-379.
[2] 陈涛,董袁航,张赛,吕程,张立红,廖春晖. 高压电缆铝护套焊缝缺陷ACFM检测方法及检测系统的研究[J]. 工程设计学报, 2022, 29(3): 394-400.
[3] 李小周, 黄华梁. 表面电沉积合金层提高碳钢齿轮的接触疲劳强度研究[J]. 工程设计学报, 2002, 9(4): 211-214.
[4] H.Bubenhagen, L.Harzheim, 刘耀乙, 毛谦德. 用形状优化法延长零件寿命[J]. 工程设计学报, 2000, 7(2): 19-23.