Please wait a minute...
工程设计学报
工程设计学报  2011, Vol. 18 Issue (2): 103-108    
工程设计理论、方法与技术     
截齿截割煤岩的LS_DYNA仿真模拟
 周游, 李国顺, 唐进元
中南大学 现代复杂装备设计与极端制造教育部重点实验室, 中南大学 机电工程学院, 湖南 长沙 410083
Simulation and analysis for pick cutting rock by LS_DYNA
 ZHOU  You, LI  Guo-Shun, TANG  Jin-Yuan
Key Laboratory of Modern Complex Equipment Design and Extreme Manufacturing of Ministry of Education, College of Mechanical and Electrical Engineering, Central South University, Changsha 410083, China
 全文: PDF(2292 KB)   HTML
摘要： 研究应用LS_DYNA软件进行煤岩截割破碎仿真的程式与方法,对悬臂式掘进机截割头上镐形截齿截割煤岩进行仿真模拟,在hypermesh中建立有限元网格模型,调用LS_DYNA971求解器进行求解,研究不同切削角对截齿截割阻力的影响以及切削厚度与比能耗之间的关系,并与常用的截齿截割阻力公式计算结果相比较,仿真结果证明了建模方法的可行性与正确性;最后得出截割阻力最小时的最佳切削角以及切削厚度与截割比能耗之间的关系．研究工作为截齿截割煤岩的动态建模及仿真提供了新思路．
关键词： 截齿;  LS_DYNA;  有限元方法;  截割阻力;  切削厚度;  截割比能耗    
Abstract: The method to build a finite element model for the pick cutting rock was discussed. The single pick on the cutting heads of longitudinal\|axis roadheaders cutting rock was simulated. The finite element model was built in hypermesh, and solved by the LS_DYNA971. The influences of resistance on different cutting angle and the relations between cutting thickness and cutting energy consumption in different cutting angle were discussed, which were also compared with the commonly used formula of the pick cutting resistance. Simulation results show that bond\|graph modeling approach is feasible and correct. Further more, The optimal pick angle of small wearing and small cutting resistance is found. And the relations between cutting thickness and cutting energy consumption were found. So, the whole result provides a new way in the field of dynamic modeling and simulation for pick cutting rock．
Key words: pick    LS_DYNA    finite element method    cutting resistance    cutting thickness    cutting energy consumption
出版日期: 2011-04-28
:  TD 421.6  
服务　　
把本文推荐给朋友
加入引用管理器
E-mail Alert
RSS
作者相关文章　　
周游
李国顺
唐进元

引用本文:

周游, 李国顺, 唐进元. 截齿截割煤岩的LS_DYNA仿真模拟[J]. 工程设计学报, 2011, 18(2): 103-108.

ZHOU You, LI Guo-Shun, TANG Jin-Yuan. Simulation and analysis for pick cutting rock by LS_DYNA[J]. Chinese Journal of Engineering Design, 2011, 18(2): 103-108.

链接本文:

https://www.zjujournals.com/gcsjxb/CN/    或    https://www.zjujournals.com/gcsjxb/CN/Y2011/V18/I2/103

[1] 张强, 刘志恒, 王海舰, 张赫哲. 截齿磨损程度的多特征信号融合识别研究[J]. 工程设计学报, 2018, 25(3): 278-287.
[2] 李强, 毛君, 张明玉, 谢苗. 采煤机截齿三向力测试方案设计及实验研究[J]. 工程设计学报, 2016, 23(5): 506-512.
[3] 彭天好, 王光耀, 张义龙, 黄鹏, 钟伟才. 基于相似理论的采煤机模拟螺旋滚筒的设计[J]. 工程设计学报, 2016, 23(4): 322-326.
[4] 杨书仪, 黎桓, 陈苍, 施林. 新型冲击沉桩机-桩-土全系统动力学特性分析[J]. 工程设计学报, 2016, 23(2): 166-171.
[5] 毛 君，潘德文，李 强，谢 苗，由旭平. 斜切进刀时采煤机滚筒力学特性分析[J]. 工程设计学报, 2015, 22(6): 613-618.
[6] 李晓豁，周 洋，刘士君，董伟松，郭 娜，杨 杰. 滚筒式采煤机截齿排列参数化设计系统的研究[J]. 工程设计学报, 2014, 21(6): 550-554.
[7] 顾晓蕾, 唐志峰, 吕福在, 刘磊. 无源自适应磁流变阻尼器的磁场设计与研究[J]. 工程设计学报, 2011, 18(5): 386-390.
[8] 唐进元, 彭方进. 基于泡沫铝“三明治”结构的吸能装置设计与吸能仿真分析[J]. 工程设计学报, 2009, 16(3): 191-195.
[9] 高晶,宋健,张步良,冯喜成. 基于MSC.Fatigue的汽车驱动桥壳疲劳寿命预估[J]. 工程设计学报, 2007, 14(3): 210-214.
[10] 薛彩军, 邱清盈, 杨为. 机械结构静动态性能协同分析方法研究[J]. 工程设计学报, 2002, 9(4): 183-186.