| Mechanical & Energy Engineering |
|
|
|
|
| Properties of frictional bridging in fiber pull-out for fiber-reinforced composites |
| LIU Peng-fei, TAO Wei-ming, GUO Yi-mu |
| Department of Engineering Mechanics, Zhejiang University, Hangzhou 310027, China |
|
|
|
Abstract Stress equilibrium equations, boundary- and continuity-conditions were used to establish a theoretical model of progressive debonding with friction at the debonded interface. On a basis of the minimum complementary energy principle, an expression for the energy release rate G was derived to explore the interfacial fracture properties. An interfacial debonding criterion G≥Γi was introduced to determine the critical debond length and the bridging law. Numerical calculation results for fiber-reinforced composite SCS-6/Ti-6Al-4V were compared with those obtained by using the shear-lag models.
|
|
Received: 23 March 2005
|
|
|
|
|
| [1] |
Begley, M.R., McMeeking, R.M., 1995. Numerical analysis of fibre bridging and fatigue crack growth in metal matrix composite materials. Materials Science and Engineering, 200(1-2):12-20.
|
|
|
| [2] |
Budiansky, B., Cui, Y.L., 1995. Toughening of ceramics by short aligned fibers. Mechanics of Materials, 21(2):139-146.
|
|
|
| [3] |
Chiang, Y.C., 2001. On fiber debonding and matrix cracking in fiber-reinforced ceramics. Composites Science and Technology, 61(12):1743-175.
|
|
|
| [4] |
Hampe, A., Kalinka, G., Meretz, S., 1995. An advanced equipment for single-fibre pull-out test designed to monitor the fracture process. Composites, 26(1):40-46.
|
|
|
| [5] |
Honda, K., Kagawa, Y., 1996. Debonding criterion in the pushout process of fiber-reinforced ceramics. Acta Materialia, 44(8):3267-3277.
|
|
|
| [6] |
Hsueh, C.H., 1996. Crack-wake interfacial debonding criteria for fiber-reinforced ceramic composites. Acta Materialia, 44(6):2211-2216.
|
|
|
| [7] |
Liu, Y.F., Kagawa, Y., 2000. The energy release rate for an interfacial debond crack in a fiber pull-out model. Composites Science and Technology, 60(2):167-171.
|
|
|
| [8] |
Marshall, M.B., Cox, B.N., 1998. A-J-integral method for calculating steady-state matrix cracking stresses in composites. Mechanics of Materials, 17(1):127-136.
|
|
|
| [9] |
McCartney, L.N., 2005. Energy-based prediction of failure in general symmetric laminates. Engineering Fracture Mechanics, 72(6):909-930.
|
|
|
| [10] |
Ochiai, S., Hojo, M., Inoue, T., 1999. Shear-lag simulation of the progress of interfacial debonding in unidirectional composites. Composites Science and Technology, 59(1):77-88.
|
|
|
| [11] |
Preuss, M., Rauchs, G., Doel, T.J.A., 2003. Measurements of fibre bridging during fatigue crack growth in Ti/SiC fibre metal matrix composites. Acta Materialia, 51(4):1045-1057.
|
|
|
| [12] |
Rauchs, G., Withers, P.J., 2002. Computational assessment of the influence of load ratio on fatigue crack growth in fibre-reinforced metal matrix composites. International Journal of Fatigue, 24(12):1205-1211.
|
|
|
| [13] |
Warrier, S.G., Maruyama, B., Majumdar, B.S., 1999. Behavior of several interfaces during fatigue crack growth in SiC/Ti-6Al-4V composites. Materials Science and Engineering, 259(2):189-200.
|
|
|
|
Viewed |
|
|
|
Full text
|
|
|
|
|
Abstract
|
|
|
|
|
Cited |
|
|
|
|
| |
Shared |
|
|
|
|
| |
Discussed |
|
|
|
|
