Please wait a minute...
工程设计学报
工程设计学报  2013, Vol. 20 Issue (2): 107-111    
工程设计理论、方法与技术     
深水勘察船基盘被动升沉补偿系统的设计研究
 羊衍贵1, 陆敏恂1, 谌志新2, 徐志强2, 张海波3
1.同济大学 机械与能源工程学院，上海 201804;
2.农业部 渔业装备与工程重点开放实验室，上海 200092；
3.北京宝石MH海洋石油工程技术有限责任公司，北京 100176
Passive heave compensation system for base plate used in deep-water exploration ship
 YANG  Yan-Gui1, LU  Min-Xun1, CHEN  Zhi-Xin2, XU  Zhi-Qiang2, ZHANG  Hai-Bo2
1.School of Machinery and Energy Engineering， Tongji University， Shanghai 201804， China; 
2. Key Laboratory of Fishery Equipment and Engineering， Ministry of Agriculture， Shanghai 200092， China；
3. Beijing BOMCO-MH Offshore Petroleum Engineering Technology Co.， Ltd.， Beijing 100176， China
 全文: PDF(723 KB)   HTML
摘要： 在深水勘察船升沉运动时，为使牵引基盘钢丝绳的拉力保持在一定的范围，设计了基盘被动升沉补偿系统．介绍了基盘被动升沉补偿系统的方案和工作原理，建立了基盘被动升沉补偿系统的数学模型，分析了钢丝绳对分析部件的拉力．对补偿系统中的滑轮组倍率、液压缸直径、液压缸行程和蓄能器总容积这4个主参数进行了分析设计，并分析了补偿系统中钢丝绳对基盘的拉力．最后针对具体的勘察船升沉运动和作业水深的设计条件以及钢丝绳对基盘的拉力范围的设计要求，通过对补偿系统中的一些设计参数的取值，对补偿系统中的主参数进行了设计计算，并对设计的补偿系统中钢丝绳对基盘的拉力进行了仿真．仿真结果表明，钢丝绳对基盘的拉力达到了设计要求．这为相关设计人员对基盘被动升沉补偿系统的设计提供了理论指导．
关键词： 基盘;  被动升沉补偿系统;  补偿液压缸;  蓄能器    
Abstract: This paper focused on the passive heave compensation system for base plate used in the deep-water exploration ship. The passive heave compensation system for base plate was utilized to keep the tension in the wire rope within certain range when the deep-water exploration ship was heaving with the sea wave. The scheme and the working principle of passive heave compensation system for base plate were presented. The mathematic models on the passive heave compensation system were constructed. The tension of the wire rope pulling the study unit was analyzed. The main parameters including the ratio value of the pulley group， the diameter of the compensation cylinder， the stroke of the compensation cylinder and the total volume of the accumulator in the passive heave compensation system were analyzed and expressed. Finally according to the design conditions of the specific heave motion of the deep-water exploration ship， the specific operation water depth and design requirements of the tension of the wire rope pulling base plate in the passive heave compensation system， the specific main parameters of passive heave compensation were calculated and the tension of the wire rope pulling base plate was simulated through some known parameters. The simulation result verifies the tension meets the design requirements. This provides an important theoretical guidance for actual designing of passive heave compensation device for base plate used in deepwater exploration ship．
Key words: base plate    passive heave compensation system    compensation hydraulic cylinder    accumulator
出版日期: 2013-04-28
基金资助:

国家科技重大专项(2008ZX05027-004).
服务　　
把本文推荐给朋友
加入引用管理器
E-mail Alert
RSS
作者相关文章　　
羊衍贵
陆敏恂
谌志新
徐志强
张海波

引用本文:

羊衍贵, 陆敏恂, 谌志新, 徐志强, 张海波. 深水勘察船基盘被动升沉补偿系统的设计研究[J]. 工程设计学报, 2013, 20(2): 107-111.

YANG Yan-Gui, LU Min-Xun, CHEN Zhi-Xin, XU Zhi-Qiang, ZHANG Hai-Bo. Passive heave compensation system for base plate used in deep-water exploration ship. Chinese Journal of Engineering Design, 2013, 20(2): 107-111.

链接本文:

https://www.zjujournals.com/gcsjxb/CN/    或    https://www.zjujournals.com/gcsjxb/CN/Y2013/V20/I2/107

[1] 石卓, 龚国芳, 刘统, 吴伟强, 彭左. TBM试验台支撑推进节能系统设计与仿真分析[J]. 工程设计学报, 2017, 24(3): 323-329.
[2] 傅斯龙, 赵宏强, 张立斌, 段焱辉. 液压凿岩机回弹缓冲装置设计与实验研究[J]. 工程设计学报, 2016, 23(5): 513-520.
[3] 赵宏强, 傅斯龙, 周茂贤, 陈庆. 液压凿岩机配流阀零位开口设计与实验研究[J]. 工程设计学报, 2016, 23(3): 288-294.
[4] 阮晓芳, 邱敏秀, 孔晓武. 蓄能器对带长管道阀控系统动态特性的改善[J]. 工程设计学报, 2002, 9(2): 97-100.