Please wait a minute...
工程设计学报  2012, Vol. 19 Issue (3): 192-195    
工程设计理论、方法与技术     
基于双模齿轮的大排量齿轮泵的流场可视化仿真研究
 陈洪月, 毛君, 张瑜
辽宁工程技术大学 机械工程学院,辽宁 阜新 123000
Visualizing simulation of flow field in the large displacementgear pump based on twomodule gears
 CHEN  Hong-Yue, MAO  Jun, ZHANG  Yu
College of Mechanical Engineering, Liaoning Technical University, Fuxin 123000, China
 全文: PDF(1425 KB)   HTML
摘要: 研究双模组合齿形齿轮泵的流量、压力特性.通过将不同模数的齿轮叠加组合,设计双模数齿形的主、从动齿轮,以增加齿轮啮合过程中的容积变化量,提高齿轮泵的排量,利用Fluent 对齿轮泵内液压流场进行了仿真,得出齿轮泵在启动和稳定工作状态下流场压力分布云图、速度分布云图和速度矢量图,并据此分析了齿轮泵流场的流态.结果表明:同体积下双模齿轮泵的输出流量是普通齿轮泵的16~33倍,该齿轮泵中大齿将流场分成不同压力区,且大齿两侧流体压力差较大,齿顶间隙处液体流动速度较大,说明齿轮泵径向泄漏较为严重,在泵的入口处存在涡流现象,会产生压力冲击,影响齿面的使用寿命.
关键词: 大排量齿轮泵双模齿轮流场仿真可视化    
Abstract: Flow,pressure characteristics of dual mode combination tooth gear pump were studied. By overlaying the different modulus,the lord,driven gear of double modulus tooth form were designed to increase the amount of volume changes in meshing process of the gear,and gear pump displacement was improved. The inside water hydraulic flow field of the external gear pump was simulated by using the software of Fluent. Flow field pressure imagery、velocity contours and velocity vector imaging were obtained under the start and steady states of gear pump,and gear pump flow pattern of the flow field was analyzed. The results show that with the same volume,output flow rate of the two module gear pump is 1.6-3.3 times than that of ordinary gear pump. The large teeth of gear pump separate flow field into different pressure region,and the large teeth,s both sides have larger pressure difference. The flow speed in tip clearance liquid is faster. All above explain that the radial leakage of the two module gear pump is more serious. The phenomenon of vortex exists in the entrance of the pump,and it will produce pressure impact,and affect the life of the tooth surface.
Key words: large displacement gear pump    two module gear    flow field simulation    visualization
出版日期: 2012-06-15
基金资助:

国家科技支持项目子课题(2007BAF12B01);2011年度辽宁工程技术大学科学研究立项计划项目(2011ZR037)

服务  
把本文推荐给朋友
加入引用管理器
E-mail Alert
RSS
作者相关文章  
陈洪月
毛君
张瑜

引用本文:

陈洪月, 毛君, 张瑜. 基于双模齿轮的大排量齿轮泵的流场可视化仿真研究[J]. 工程设计学报, 2012, 19(3): 192-195.

CHEN Hong-Yue, MAO Jun, ZHANG Yu. Visualizing simulation of flow field in the large displacementgear pump based on twomodule gears. Chinese Journal of Engineering Design, 2012, 19(3): 192-195.

链接本文:

https://www.zjujournals.com/gcsjxb/CN/        https://www.zjujournals.com/gcsjxb/CN/Y2012/V19/I3/192

[1] 曹鹏勇, 王建文. 基于STM8S105的智能车结构及控制系统的研究[J]. 工程设计学报, 2020, 27(4): 516-523.
[2] 李艳鸽,李粮纲,张乾. 基于优化GM(1,1)模型的可视化沉降预测数据的精度研究[J]. 工程设计学报, 2009, 16(2): 145-149.
[3] 张 繤, 干 静, 蒋春林. 工程机械可视化定制系统的研究与构建[J]. 工程设计学报, 2006, 13(6): 369-373.
[4] 孙伟, 韩清凯, 于涛, 闻邦椿. 汽车变速器装配线的可视化仿真系统研究[J]. 工程设计学报, 2006, 13(4): 245-248.
[5] 徐小良, 汪乐宇, 周 泓. VPP虚拟仪器元件库的实现框架[J]. 工程设计学报, 2003, 10(2): 75-79.
[6] 王瑞荣, 周泓, 耿晨歌, 汪乐宇. 单率异步数据流语言的RTL文法设计[J]. 工程设计学报, 2002, 9(1): 31-35.
[7] 刘玉生. 可视化公差分析方法的研究[J]. 工程设计学报, 2001, 8(4): 168-172.