Please wait a minute...
工程设计学报  2009, Vol. 16 Issue (6): 462-466    
机电一体化和智能化系统设计理论、方法与技术     
涡旋压缩机转子加工误差快速测量系统的研究
 杨建红, 房怀英
华侨大学 机电及自动化学院,福建 泉州 362021
Research on machining error rapid measurement system for rotors on orbit scroll compressors
 YANG  Jian-Hong, FANG  Huai-Ying
College of Mechanical Engineering and Automation, Huaqiao University, Quanzhou 362021, China
 全文: PDF(3702 KB)   HTML
摘要: 加工坐标系和涡旋体旋转坐标系偏差会引起较大的侧面啮合间隙,加工坐标系的在线调整能提高涡旋体加工精度.基于极坐标系开发了涡旋体侧面轮廓快速测量系统,可调对齐平台能精确确定测量坐标系原点.分析并去除了测量系统误差,通过涡旋体径向误差三维粒子群寻优计算,得到加工坐标系和涡旋体旋转坐标系的坐标偏差和旋转角度偏差.新的测量系统获得了同三坐标测量机(CMM)相同的测量结果,同时测量时间从20 min缩短为180 s,测量环境和测量时间能满足涡旋体在线加工补偿的要求.
关键词: 涡旋体快速测量测量球加工误差涡旋压缩机    
Abstract: The coordinate deviations between machining coordinates systems and workpiece coordinate systems can lead to a larger flank profile leakage. The online adjustment of the machining coordinates system can increase machining accuracy of scroll profiles. A novel rapid measurement system of machining error for scroll profiles was developed based on polar coordinates system and the centre point of the rotary stage can be adjusted accurately by an auto alignment table. The measurement errors of the proposed measurement system were analyzed and then removed. The machining error of the scroll profile was calculated by threedimensional particle swarm optimization. The measurement results of the new measurement system were the same as those of the CMM after compensating measurement system error and machining error. But the measurement time of the proposed measurement system was much shorter than that of the CMM. The measurement time and condition of the rapid measurement system can meet the requirement of the online measurement for scroll profiles.
Key words: scroll profile    rapid measurement    measurement ball    machining error    scroll compressor
出版日期: 2009-12-28
:  TH 455.06  
基金资助:

福建省自然科学基金资助项目(D0810019)

服务  
把本文推荐给朋友
加入引用管理器
E-mail Alert
RSS
作者相关文章  
杨建红
房怀英

引用本文:

杨建红, 房怀英. 涡旋压缩机转子加工误差快速测量系统的研究[J]. 工程设计学报, 2009, 16(6): 462-466.

YANG Jian-Hong, FANG Huai-Ying. Research on machining error rapid measurement system for rotors on orbit scroll compressors[J]. Chinese Journal of Engineering Design, 2009, 16(6): 462-466.

链接本文:

https://www.zjujournals.com/gcsjxb/CN/        https://www.zjujournals.com/gcsjxb/CN/Y2009/V16/I6/462

[1] 李哲, 李华龙, 王小强, 孙志超, 苏兴旺. 进给系统刚度对内球面车削的误差影响研究[J]. 工程设计学报, 2012, 19(4): 268-273.
[2] 杨启志, 姚斌斌, 庄佳奇, 尹小琴. 基于高频柔性并联激振台柔性转动关节的加工误差分析[J]. 工程设计学报, 2012, 19(3): 170-173.