Please wait a minute...
工程设计学报  2009, Vol. 16 Issue (5): 364-368    
本刊特稿     
基于弹流润滑与动力学耦合的WN齿轮传动的强度设计
 陈殿华, 李玉光
大连大学 机械工程学院, 辽宁 大连 116022
Strength design of WN gear transmission based on coupling of elastohydrodyamic lubrication and dynamics
 CHEN  Dian-Hua, LI  Yu-Guang
Mechanical Engineering College, Dalian University, Dalian 116022, China
 全文: PDF(402 KB)   HTML
摘要: 提出应用动力学与弹流润滑耦合原理进行WN (WildhaberNovikov)齿轮强度分析的方法.依据振动学、油膜承载机理及其数值分析法,结合WN齿轮啮合原理,创建了该齿轮传动润滑与振动力学耦合分析模型.利用齿轮副的接触弹性和接触衰减描述轮齿弯曲载荷,考虑了啮合中同时啮合齿数变化对其刚度的影响,进行了啮合过程中多因素综合情况下的强度分析.计算分析与实验结果相符,为WN齿轮传动及其结构强度优化设计提供了参考.
关键词: WN齿轮强度分析振动力学弹流润滑    
Abstract: The coupling theory of dynamics and elastohydrodynamic lubrication is applied to strength analysis of WN (Wildhaber-Novikov) gear. Based on vibration theory and load capacity of oil film analysis and numerical solution method, combined with WN gear pair meshing theory, a new coupling analysis model of WN gear transmission lubrication and vibration dynamics is established.A spring and damping model of WN gear pair are utilized to describe the force generated by bending of the contact tooth, and the change of the number of meshing positions as well as its effect on stiffness was taken into consideration. The strength analysis in meshing under coupled multiple factors is carried out. The calculation analysis and experimental results of instance accord with each other well. This method provides application reference for transmission and optimization design of construction strength of WN gears.
Key words: WN gear    strength analysis    vibration dynamics    elasticity hydrodynamics lubrication
出版日期: 2009-10-28
基金资助:

辽宁省教育厅资助项目(20060075)

服务  
把本文推荐给朋友
加入引用管理器
E-mail Alert
RSS
作者相关文章  
陈殿华
李玉光

引用本文:

陈殿华, 李玉光. 基于弹流润滑与动力学耦合的WN齿轮传动的强度设计[J]. 工程设计学报, 2009, 16(5): 364-368.

CHEN Dian-Hua, LI Yu-Guang. Strength design of WN gear transmission based on coupling of elastohydrodyamic lubrication and dynamics[J]. Chinese Journal of Engineering Design, 2009, 16(5): 364-368.

链接本文:

https://www.zjujournals.com/gcsjxb/CN/        https://www.zjujournals.com/gcsjxb/CN/Y2009/V16/I5/364

[1] 张毅,熊思阳,钟思鹏,熊子杰,杨强. 密封面磨损对V形组合密封圈性能的影响[J]. 工程设计学报, 2023, 30(2): 237-243.
[2] 邹玉静,常德功. 考虑动载荷和表面粗糙度的渐开线齿轮摩擦因数的研究[J]. 工程设计学报, 2014, 21(3): 285-291.
[3] 陈殿华, 李成超. 基于负载与啮合特征的WN齿轮传动接触强度分析[J]. 工程设计学报, 2012, 19(4): 294-297.
[4] H.Bubenhagen, L.Harzheim, 刘耀乙, 毛谦德. 用形状优化法延长零件寿命[J]. 工程设计学报, 2000, 7(2): 19-23.